Sharp Xg Ph70x Projector User Manual

							Introduction
-19
Using the Remote Control as a Wireless Computer Mouse
When connecting the supplied remote
mouse receiver to the computer, you can use
the remote control as the wireless computer
mouse.
1Connect the supplied remote
mouse receiver to the USB termi-
nal on the computer.
2Slide the ADJ./MOUSE
switch on the remote con-
trol to the MOUSE position.
3Use the mouse function.
• P oint the remote control at the remote
mouse receiver.
■ When moving the cursor
Press  '/" /\ /| .
■ When left-clicking
Press 
.
■ When right-clicking
Press 
.
■ When your computer supports only a
one-click mouse (such as Macintosh
®)
Press 
  or .  (  and  have com-
mon function.)
ADJ.
MOUSE
Remote mouse
receiver
Supplied
accessory
Note
• This function only works with the Microsoft®
Windows® OS and Mac OS®.  However, this func-
tion does not work with the following operation
systems that do not support USB.
•V ersions earlier than Windows® 95.
•V ersions earlier than Windows® NT4.0.
•V ersions earlier than Mac OS® 8.5.
• Confirm that the computer recognizes the USB
connection.
• While the remote control is connected to the
projector with a signal cable, you cannot use
the wireless computer mouse function.
Computer
To USB terminal
Remote mouse receiver
Mouse/adjustment button ( '/" /\ /| )
ADJ./MOUSE switch
R-click button
L-click button 
						

							-20
Quick Start
Page 22
1.Place the projector facing a screen
Pages 27–29, 37
Page 37
Press  on the projector or  on the remote control.
This section shows the basic operation (projector connecting with the computer). For details, see the page
described below for each step.
Setup and Projection
In this section, connection of the projector and the computer is explained using one example.
2.Connect the projector to the computer and plug the power
cord into the AC socket of the projector
3.Remove the lens cap and turn the projector on
When connecting equipment other than the computer,
see pages 
30–36 .
5 
4
6
6
7
6
3 4
83
4
6
7
46
8
5 
						

							Quick Start
-21
Pages 38, 39
4.Adjust the angle
5.Adjust the focus and the zoom
Page 40
8.Turn the power off
Page 37
7.Select the input mode
Page 45
1
1 1
1
1 Press  on the projector or  on the remote control to adjust the focus.
2
2 2
2
2 Press 
 on the projector or  on the remote control to adjust the zoom.
Press  on the projector or  on the
remote control to select the “INPUT 1” mode.
•
• •
•
• When pressing  on the projector, input mode switches in order of : INPUT 1 INPUT 2 INPUT 3.
Pressing 
 on the projector switches between “INPUT 4” and “INPUT 5”.
•
• •
•
• When using the remote control, press 
//// to switch the input mode.
Press  on the projector or  on the remote control. While the confirmation message is displayed,
press 
 or  again.
•
• •
•
• You can unplug the power cord even if the projector is operating.
•
• •
•
• Even if you unplug the power cord from the AC outlet, the cooling fan continues to run for a while.
Adjust the projector angle
•
• •
•
•
Shift the lens horizontally and vertically.
1
1 1
1
1Press  on the projector or  on the
remote control.
2
2 2
2
2Press ' , " , \  or  | on the projector or the
remote control.
•
• •
•
•Adjust the projector angle by rotating the adjust-
ment feet.
6.Correcting the image distortion due to the projection angle
1
1 1
1
1 Press  on the projector or  on the
remote control.
2
2 2
2
2 Press 
 on the projector or  on the
remote control.
3
3 3
3
3 Press  ', " , \  or  |  to move the position for
the upper left of the image.
Page 41
4
4 4
4
4 Press  or  to set the position.
5
5 5
5
5 Repeat the same procedure with the positions
f or the upper right, lower right and lower left of
the image.
•
• •
•
•
When the position of the lower left is set, the
correction is made and the display disappears.
"
" "
"
"  On-screen Display (RGB)
"
" "
"
"  On-screen Display 
						

							-22
Setting Up the Projector
For optimal image quality, position the projector perpendicular to the screen with the projector’s feet flat
and level. Doing so will eliminate the need for Keystone correction and provide the best image quality.
Note
•The projector lens should be centered in the middle of the screen. If the horizontal line passing through
the lens center is not perpendicular to the screen, the image will be distorted, making viewing difficult.
• For an optimal image, position the screen so that it is not in direct sunlight or room light\
. Light falling
directly on the screen washes out the colors, making viewing difficult. Close the curtains and dim the lights
when setting up the projector in a sunny or bright room.
Standard Setup (Front Projection)
■ Place the projector at the required distance from the screen according t\
o the desired picture size. (For
details, refer to “SETUP MANUAL” contained on the supplied CD-ROM.)
Setting Up the Projector
Indication of the Projection Image Size and Projection Distance
For details, refer to “SETUP MANUAL” contained on the supplied CD-ROM.
Example : NORMAL Mode (4:3) for the standard zoom lens (AN-PH31EZ)
300
200
100 84
60
Picture Size240
×180
160×120
80×6067×5048×36
Projection Distance
36–44(11.0 m – 13.4 m)24–294
(7.3 m – 8.9 m)12–148
(3.7 m – 4.5 m)101–124
(3.1 m – 3.8 m)72–810
(2.2 m – 2.7 m) 
						

							Setup
-23
Projecting a Reversed Image
Projection from behind the Screen
■Place a translucent screen between the projector and the audience.
■ Reverse the image by setting “Rear” in the “PRJ Mode” menu. (See page 
84 .)
Projection Using a Mirror
■Place a mirror (normal flat type) in front of the lens.
■ When the translucent screen is placed between the mirror and audience, set to “Front” in the “PRJ Mode”
menu. (See page 
84 .)
■ When the mirror is placed on the audience side, set to “Rear” in the “PRJ Mode” menu. (See page 
84 .)
Info
•When using a mirror, ensure that both the projector and the mirror are carefully placed so \
the projected
light does not shine into the eyes of the audience.
Ceiling-mount Setup
■ It is recommended that you use the optional Sharp ceiling-mount
bracket for this installation.
Before mounting the projector, contact your nearest Sharp Au-
thorized Projector Dealer or Service Center to obtain the recom-
mended ceiling-mount bracket (sold separately).
•AN-PHCM20 ceiling-mount bracket, its AN-EP101AP extension
tube (for the U.S.A.).
• AN-NV6T ceiling-mount bracket, its AN-TK201 and AN-TK202
extension tubes (for countries other than the U.S.A.).
■ Invert the image by setting “Ceiling + Front” in “PRJ Mode”. See
page 
84  for use of this function.
Translucent screen
A udience
Set to “Front”
A udience Tr
anslucent screen Mirror
Set to “Rear”
A
udience
Mirror 
						

							-24
INPUT/OUTPUT Terminals and Connectable Main Equipment
AUDIO input (2, 3) terminalConnecting an audio cable. (Shared 
audio input terminal for INPUT 2 
and 3.) (See pages 28 and  29.) 
AUDIO input (1) terminalConnecting an audio cable. 
(Audio input terminal 
dedicated to INPUT 1.) (See 
page  27.)
AUDIO input (4, 5) terminalsConnecting an audio cable. 
(Shared audio input terminals for 
INPUT 4 and 5.) (See page  34.)
WIRED REMOTE terminalFor connecting the remote control when 
the signals from the remote control cannot 
reach the remote control sensor. (See 
page  18.) 
AUDIO OUTPUT terminalConnecting an audio cable. 
(Shared audio output terminal for 
INPUT 1 – 5.) (See page  36.)
LAN terminal(10 BASE-T/100 BASE-TX) Connecting the computer or the 
hub using a LAN cable. (See page 
35.)
INPUT 5 terminalConnecting video equipment with S-video 
output terminal (VCR, DVD player, etc.).
(See page  34.)
RS-232C terminalConnecting the computer to 
control the projector. 
(See page  35.)
INPUT 4 terminalConnecting video equipment without 
S-video output terminal. (See page  34.)
OUTPUT (FOR INPUT 1, 2) 
terminal
Connecting the monitor when you 
want to simultaneously watch the 
projection image on the monitor. 
(See page  36.)INPUT 1, 2 terminalConnecting the computer. (See 
pages  27 and  28 .)
Connecting video equipment with 
component output terminal (DVD 
player, DTV decoder, DVD recorder 
with hard disc, etc.). (See page  33.)
INPUT 3 terminalConnecting the computer. (See 
page  29.)
Connecting video equipment with 
HDMI or DVI output terminal (DVD 
player, DTV decoder, DVD recorder 
with hard disc, etc.). (See pages  30 
and  31 .)
Connections 
						

							Connections
-25
Terminal on the
projector
INPUT 1
INPUT 2
INPUT 3
A UDIO  (for INPUT 1)
AUDIO  (for INPUT 2, 3)
INPUT 3
INPUT 2
INPUT 1
INPUT 2
Equipment
Computer
A
udio-visual
equipment
T erminal on
connected equipment
RGB
output
terminal
D VI digital
video
output
terminal
A udio
output
terminal
HDMI
output
terminal
D VI digital
video
output
terminal
RGB
output
terminal
Component video
output
terminal Cable
RGB cable (supplied)
5 BNC to 15-pin D-sub cable (commercially available)
D
VI Digital cable (commercially available)
ø3.5 mm stereo or mono audio cable (commercially
av ailable  or available as Sharp service part
QCNWGA038WJPZ)
D VI to HDMI cable (commercially available)
DVI Digital cable (commercially available)
5 RCA RGB cable  (commercially available)
BNC to RCA adaptors (commercially available)
3 RCA to 15-pin D-sub cable (optional: AN-C3CP2)
BNC to RCA adaptors (commercially available)
Component video cable (commercially available)
Samples of Cables for Connection
•F or more details of connection and cables, refer to the operation manual of the connecting equipment.
•Y ou may need other cables or connectors not listed below. 
						

							-26
Terminal on the
projector
INPUT 4
INPUT 5
A UDIO  (for INPUT 1)
AUDIO  (for INPUT 2, 3)
AUDIO  (for INPUT 4, 5)
OUTPUT
AUDIO OUTPUT
Equipment
A
udio-visual
equipment
Monitor
Amplifier
T erminal on
connected equipment
Video
output
terminal
S-video
output
terminal
A udio
output
terminal
RGB
input
terminal
A udio
input
terminal
Cable
Video cable (commercially available)
S-video cable (commercially available)
ø3.5 mm stereo minijack to RCA audio cable
(commercially available)
RCA audio cable (commercially available)
RGB cable (supplied or commercially available)
ø3.5 mm stereo minijack to RCA audio cable
(commercially available)
Samples of Cables for Connection 
						

							Connections
-27
Connecting to a Computer
Before connecting, ensure the power cord of the projector from the AC outlet is unplugged,
and that the devices to be connected are turned off. After making all connections, turn on the
projector and then the other devices. When connecting a computer, ensure that it is the last
device to be turned on after all the connections are made.
Ensure the operation manuals of the devices to be connected have been read before making connections.
Note
•See page  100 “Computer Compatibility Chart” for a list of computer signals compatible with the projector.
Use with computer signals other than those listed may cause some of the functions to not work.
• Connecting computers other than the recommended types may result in damage to the projector, the
computer, or both.
• A Macintosh adaptor may be required for use with some Macintosh computers. Contact your nearest
Macintosh Dealer.
• Depending on the computer you are using, an image may not be projected unless the computer’s
external output port is switched on. (e.g. Press “Fn” and “F5” keys simultaneously when using a
SHARP notebook computer).  Refer to the specific instructions in your computer’s operation manual to
enable your computer’s external output port.
Connecting with the RGB Cable
RGB cable
Supplied
accessory
Note
• With this connection, the projector is not compatible to the sync on green signals.
•
When using the ø3.5 mm mono audio cable, the volume level will be half of when using the ø3.5 mm stereo audio cable.
To audio output terminal To RGB output 
terminal
To INPUT 1 terminal
ø3.5 mm stereo or mono audio cable 
(commercially available or available as Sharp 
service part QCNWGA038WJPZ)
RGB cable To AUDIO input (1) terminal
ComputerSide view 
						

							-28
Connecting with a 5 BNC to 15-pin D-sub Cable
The projector employs a 5 BNC computer input to prevent deterioration of image quality.
When connecting the input terminals on the projector to the computer directly, Connect the
R (P
R), G/G sync (Y), B (PB), HD/C sync and VD cables of the 5 BNC to 15-pin D-sub cable
(commercially available) to the INPUT 2 terminals on the projector.
Note
• When connecting the projector to a compatible computer other than a PC (VGA/SVGA/XGA/SXGA/UXGA)
or Macintosh (i.e. Workstation), a separate cable may be needed. Please contact your dealer for more
information.
• When using the ø3.5 mm mono audio cable, the volume level will be half of when using the ø3.5 mm
stereo audio cable.
• The HD/C sync terminal is only for TTL signal.
ComputerSide view
ø3.5 mm stereo or mono audio cable 
(commercially available or available as 
Sharp service part QCNWGA038WJPZ)
To INPUT 2 terminals 
5 BNC to 15-pin D-sub cable 
(commercially available) To AUDIO input 
(2, 3) terminal 
To audio output 
terminal
To RGB output 
terminal
Connecting to a Computer