Sharp Xg Ph70x Projector Quickstart Guide

							-21
Setting up the Projector Network Environment
3. Setting up a NetworkConnection for the
Projector
Settings for such items as the projector’s IP
address and subnet mask are compatible with
the existing network.
Set each item on the projector as follows. (See
page 89 of the projector’s operation manual
for setting.)
DHCP Client : OFF
IP Address : 192.168.150.002
Subnet Mask : 255.255.255.000
1Start Internet Explorer (version
5.0 or later) on the computer, and
enter “http://192.168.150.2/” in
“Address”, and then press the
“Enter” key.
2If a user name and a password
have not yet been set, just click
the “OK”  button.
•If a user name and a password have
been set, input the user name and the
password, and click the “OK” button.
• If the user name or password is entered
incorrectly three times, an error mes-
sage will be displayed.
3When the screen as shown on
the right appears, click “TCP/IP”. 
						

							-22
Setting up the Projector Network Environment
4The TCP/IP setting screen ap-
pears, ready for network settings
for the projector.
Note
•Confirm the existing network’s segment (IP
address group) to avoid setting an IP ad-
dress that duplicates the IP addresses of
other network equipment or computers. If
“192.168.150.2” is not used in the network
having an IP address of “192.168.150.XXX”,
you don’t have to change the projector IP
address.
• For details about each setting, consult your
network administrator.
5Click the “Apply” button.
6The set values appear. Confirm
that the values are set properly,
and then click the “Confirm” but-
ton.
• Close the browser.
• This completes the network settings.
• After setting items, wait for 10 seconds and then re-access.
• Change the IP address of the setting computer back to its original address, which you have noted down in
Step 6- 1 on page 
20, and then connect the computer and the projector to the network.
Setting example / RemarksSelect “ON” or “OFF” to determinewhether to use DHCP Client.
You can set this item when “DHCP
Client” is set to “OFF”.
Factory default setting: 192.168.150.2
Enter an IP address appropriate
for the network.
You can set this item when “DHCP
Client” is set to “OFF”.
Factory default setting: 255.255.255.0
Set the subnet mask to the same
as that of the computer and
equipment on the network.
You can set this item when “DHCP
Client” is set to “OFF”.
Factory default setting: 0.0.0.0
* When not in use, set to “0.0.0.0”.
Factory default setting: 0.0.0.0
* When not in use, set to “0.0.0.0”.
ItemsDHCPClient
IP Address
Subnet
Mask
Default
Gateway
DNS
Server 
						

							-23
Controlling the Projector via LAN
Controlling the Projector
Using Internet Explorer
(Version 5.0 or later)
Complete connections to external equipment
before starting the operation. (See pages 24-
36 of the projector’s operation manual.)
Complete the AC cord connection. (See page
37 of the projector’s operation manual.)
Note
•When connecting the projector to the LAN, use a
commercially available LAN cable (UTP cable,
Category 5, cross-over type).  When connecting
the projector to a hub, use a straight-through cable.
1Start Internet Explorer (version 5.0
or later) on the computer.
2Enter “http://” followed by the
projector IP address set by the
procedure on page 
22 followed
by “/” in “Address”, and then
press the “Enter” key.
•The factory default setting for the projector :
“DHCP Client” is “OFF” and IP address is
“192.168.150.2”. If you did not change the IP
address in  “3. Setting up a Network Con-
nection for the Projector”  (pages 
21-22),
enter “http://192.168.150.2/”.
3A screen for controlling the pro-
jector appears, ready for per-
forming v arious status  condi-
tions,  control, and settings.
After connecting the projector to your network, enter the projector IP address in “Address”
on Internet Explorer (version 5.0 or later) using a computer on the network to start a setup
screen that will enable control of the projector via the network. 
						

							-24
Confirming the Projector
Status (Status)
On this screen, you can confirm the projector
status. You can confirm the following items :
•MAC Address
•Power
•Condition
•Lamp Timer  1
•Lamp Timer  2
•Lamp Life 1
•Lamp Life 2
•Input
•Signal Info
•Serial Number
Note
•If you click the “Refresh” button before the
screen is displayed completely, an error
message (“Server Busy Error”) will be dis-
played. Wait for a moment and then oper-
ate again.
• For details about each item, refer to the
projector’s operation manual.
Controlling the Projector via LAN
Controlling the Projector
(Control)
On this screen, you can perform projector con-
trol. You can control the following items :
•Po wer
•Input Select
•Volume
•M ute (Audio)
•Black Screen
Note
•If you click the “Refresh” button before the
screen is displayed completely, an error mes-
sage (“Server Busy Error”) will be displayed.
W ait for a moment and then operate again.
• You cannot operate this page while the pro-
je ctor  is  wa rming up.
• While the projector is in standby mode, you
can only control “Power ON”.
• For details about each item, refer to the
projector’s operation manual. 
						

							-25
Controlling the Projector via LAN
Setting and Adjusting the
Projector (Settings & Adjustments)
Example: “Picture” screen display for INPUT 1
On these screens, you can make projector
settings or adjustments. You can set or adjust
the following items :
• Picture Mode
• CLR Temp
• Bright Boost
• Progressive
• C.M.S. Adjustment
• DNR
• Signal Type
• Auto Sync
• Auto Sync  Disp
• Audio Out
• Internal  Speaker
• Resize
• OSD Display
• Video System (INPUT 4/5)
• Background
• Startup Image
• Eco Mode
• Auto Search
• Auto Power Off
• Password
• Lamp Mode
• Pr oject ion Mode
• Ke ylock Level
• Set Inputs
• Fan Mode
• Direct Power On
• RS-232C  Speed
• Monitor Out (Standby)
• Video Wall (See page  41.)
• Stack Setting (See page  38.)
• All Reset
• OSD Language
Note
•If you click the “Refresh” button before the
screen is displayed completely, an error mes-
sage (“Server Busy Error”) will be displayed.
W ait for a moment and then operate again.
• You cannot operate this page while the pro-
jector is warming up.
• While the projector is in standby mode, you
can only control “Power ON”.
• For details about each item, refer to the
projector’s operation manual.
Setting the Security
(Network – Security)
On this screen, you can make settings relat-
ing to security.
After clicking the 
“Apply”  b utton, the set val-
ues appear. Confirm that the values are set
properly, and then click the 
“Confirm”  b utton.
Note
• After setting items, wait for 10 seconds and
then re-access.
• User Name and Password can be up to 8
characters.
• You can input the characters below :
a-z, A-Z, 0-9, -, _
• To  cancel User Name and Password, enter
nothing and then press “Apply” button.
Description
Setting of user name for
security protection.
Setting of password for
security protection.
It is possible to set up to three
IP addresses allowing connec-
tion to the projector.
No limits are set to IP addresses
connecting to the projector.
Fo r security improvement, only an
IP address set by “Address 1-3”
can be connected to the projector.
ItemsUser Name
P assword
Accept IP
Address
All IP
AddressesFrom only
specific IP
addresses 
						

							-26
Controlling the Projector via LAN
Making General Settings
for the Network 
(Network –
General)
On this screen, you can make general settings
relating to the network.
After clicking the “Apply” button, the set val-
ues appear. Confirm that the values are set
properly, and then click the “Confirm” but-
ton.
Note
•After setting items, wait for 10 seconds and
then re-access.
• Projector Name can be up to 12 characters.
• You can input the  characters below :
A-Z, 0-9, -, _, (, ), space
(When “a-z” are input, they are converted to
“A-Z” automatically.)
Description
Setting the projector name.
Setting the time interval in
which the projector will be
automatically disconnected
from the network in units of a
minute (from 1 to 65535
minutes). If the set value is
made 0, the Auto Logout
function is disabled.
Setting the TCP port number
used when exchanging data
with the projector (from 1025 to
65535).
Setting the port number used
when searching for the
projector (from 1025 to 65535).
ItemsProjector
Name
Auto
Logout
Time
Data Port
Search
Po r t
Setting example / Remarks
Setting an SMTP server
address for e-mail transmis-
sion.
e.g.1 : 192.168.150.253
e.g.2 : smtp123.sharp.co.jp
* When using a domain name, make settings for the DNS
server.
Setting  the projector’s e-mail
address. The e-mail address set
here becomes Originator E-mail
Address.
Setting the sender’s name.
The name set here appears in
the “Originator Name” column
of the body of the message.
Items
SMTP
Server
Originator
E-mail
Address
Originator
Name
Setting for Sending E-mail
when an Error Occurs
(Mail – Originator Settings)
On this screen, you can make settings for
sending e-mail to report when the projector
has generated an error.
Note
• SMTP Server, Originator E-mail Address and
Originator Name can be up to 64 characters.
•
You can input the characters below:
SMTP Server and Originator E-mail Address :
a-z, A-Z, 0-9, !, #, $, %, &, *, +, -, /, =, ?, ^, {,
|, },  ~
, _, ’, ., @, `
(You can input “@” only one time for “Origi-
nator E-mail Address”.)
Originator Name : a-z, A-Z, 0-9, -, _, (, ),
space
•
If the settings of  “3. Setting up a Network
Connection for the Projector”  on pages 
21
and 22 are incorrectly set, e-mail will not be
sent. 
						

							-27
Controlling the Projector via LAN
Setting  Error Items and
Destination Addresses to
which E-mail is to be Sent
when an Error Occurs
(Mail – Recipient Settings)
On this screen, you can input e-mail destina-
tions to which error  notification (error items)
e-mails are sent.
Note
• E-mail Address can be up to 64 characters.
• You can input the  characters below :
a-z, A-Z, 0-9, !, #, $, %, &, *, +, -, /, =, ?, ^, {, |,
},  ~
, _, ’, ., @, `
(You can input “@” only one time.)
• For details about error items, refer to the
projector’s operation manual.
Description
Set addresses to which error
notification e-mail is sent. You
can set up to five addresses.
Error e-mail is sent on the error
items checked in their check
boxes.
Send test e-mail. This allows
y ou to confirm that the settings
f or e-mail transmission are
properly set.
ItemsE-mail
Address
Error Mail(Lamp, Temp,
F an, Cover)Test
Setting  Error Items and
the URL that are to be
Displayed when an Error
Occurs 
( Service & Support –
Access URL)
On this screen, you can make settings of the
URL and error items that are to be displayed
when the projector has generated an error.
Example of the display when an error occurs
Description
Set the URL that is to be
displayed when an error
occurs. You can set up to five
addresses.
The URL is displayed when an
error checked in their check
boxes occurs.
The set URL site is test-
displayed. This allows you to
confirm that the URL site is
properly displayed.
ItemsAccess
URL
Condition
(Always, Lamp,T emp, Fan, Cover)Test 
						

							-28
Setting the Projector Using RS-232C or Telnet
When Connecting Using
RS-232C
1Launch general purpose terminal
emulator.
2Input settings for the RS-232C port
of the terminal emulator as follows.
Baud Rate : 9600 bps*
Data Length : 8 bit
Pa rity Bit : None
Stop Bit : 1 bit
Flow Control : None
* This is the factory default setting. If the value
of Baud Rate for the projector has been
changed, set Baud Rate here according to
the changed value on the projector.
3Input “PJS11234” and press the “En-
ter” key.
4“OK” is displayed. Input “PJS25678”
and press the “Enter” key within 10
seconds.
5“OK” is displayed. Press the “En-
ter” key.
6“User Name:” is displayed. Input the
user name and press the “Enter”
key.
•If a user name has not yet been set, just
press the “Enter” key.
Connect the projector to a computer using RS-232C or Telnet, and open the SETUP MENU on
the computer to carry out various settings for the projector.
7“Password:” is displayed. Input the
password and press the “Enter” key.
•If a password has not yet been set, just press
the “Enter” key.
8Input “setup” and press the “Enter”
key.
•SETUP MENU will be displayed.
Note
•User name and password are not set in the fac-
tory default  settings.
• If the user name or password is entered incor-
rectly three times, SETUP MENU will be quit.
▼
SETUP MENU
---------------------------------SETUP MENU-----------------------------\
---
[1]IP Address [2]Subnet Mask [3]Default Gateway
[4]User Name [5]Password
[6]RS-232C Baud Rate [7]Projector Name [8]DHCP Client
[A]Advanced Setup [D]Disconnect All
[V]View All Setting [S]Save & Quit [Q]Quit Unchanged
setup> 
						

							-29
Setting the Projector Using RS-232C or Telnet
When Connecting Using
Telnet
1Click “start” from the Windows® desk-
top and select “Run”.
2Enter “telnet 192.168.150.2” in the text
box that opens up. (If the IP address
of the projector is 192.168.150.2.)
3Click  the “OK”  button.
4“User Name:” is displayed. Input the
user name and press the “Enter”
key.
•If a user name has not yet been set, just
press the “Enter” key.
5“Password:” is displayed. Input the
password and press the “Enter” key.
•If a password has not yet been set, just press
the “Enter” key.
6Input “setup” and press the “Enter”
key.
•SETUP MENU will be displayed.
Note
•If the IP address has been changed, be  sure to
enter the new IP  address in step 2.
• User name and password are not set in the fac-
tory default  settings.
• If the user name or password is entered incor-
rectly three times in  steps 4 or 5, SETUP MENU
will be quit.
---------------------------------SETUP MENU-----------------------------\
---
[1]IP Address [2]Subnet Mask [3]Default Gateway
[4]User Name [5]Password
[6]RS-232C Baud Rate [7]Projector Name [8]DHCP Client
[A]Advanced Setup [D]Disconnect All
[V]View All Setting [S]Save & Quit [Q]Quit Unchanged
setup>
▼ SETUP MENU 
						

							-30
Setting the Projector Using RS-232C or Telnet
SETUP MENU (Main Menu)
[1]IP Address (Factory default setting : 192.168.150.2)
IP address settings. (Page  33)
[2] Subnet Mask (Factory default setting :
255.255.255.0)
Subnet mask settings. (Page  33)
[3] Default Gateway (Factory default setting : Not
Used)
Default gateway settings. (Page  33)
[4] User Name (Factory default setting : Not Re-
quired)
Setting of user name for security protection. (Page  33)
[5] Password (Factory default setting : Not Required)
Setting of password for security protection. (Page  34)
[6] RS-232C Baud Rate (Factory default setting :
9600 bps)
Baud rate settings for the RS-232C terminals. (Page
34)
[7] Projector Name It is possible to assign a projector name. (Page  34)
[8] DHCP Client DHCP Client settings. (Page  34)
[A] Advanced Setup
Enters ADVANCED SETUP MENU. (Page  35)
[D] Disconnect All Disconnect all connections. (Page  35)
[V] View All Setting Displays all setting values. (Page  31)
Can also be used with ADVANCED SETUP MENU.
[S] Save & Quit Save set values and quit menu. (Page  32)
[Q]Quit Unchanged
Quit menu without saving setting values. (Page  32)
Note
•The factory default settings for the projector are
as follows:
DHCP Client : OFF
IP address : 192.168.150.2
Subnet mask : 255.255.255.0
Default gateway : 0.0.0.0
ADVANCED SETUP MENU
[1] Auto Logout Time (Factory default setting : 5 min-
utes)
Setting of time until automatic disconnection of net- wo rk connection. (Page  35)
[2] Data Port (Factory default setting : 10002) Setting the TCP port number used when exchang-ing data. (Page  35)
[5] Network Ping Test It is possible to confirm that a network connectionbetween the projector and a computer etc. is work-
ing normally. (Page  36)
[6] Accept IP Addr(1)
[7] Accept IP Addr(2)
[8] Accept IP Addr(3)
[9] Accept All IP Addr (Factory default setting : Ac- cept All)
F or improved security, it is possible to set up to three
IP addresses allowing connection to the projector.
Set IP addresses can be cancelled using [9] Accept
All IP Addr. (Page  36)
[0] Search Port (Factory default setting : 5006) Setting the port number used when searching for
the projector. (Page  37)
[!] Restore Default Setting Restores all setting values that can be set using the
menu to the default state. (Page  37)
[Q]Return to Main Menu Return to the main SETUP MENU. (Page  37)
▼SETUP MENU ▼ADVANCED SETUP MENU
---------------------------------SETUP MENU-----------------------------\
---
[1]IP Address [2]Subnet Mask [3]Default Gateway
[4]User Name [5]Password
[6]RS-232C Baud Rate [7]Projector Name [8]DHCP Client
[A]Advanced Setup [D]Disconnect All
[V]View All Setting [S]Save & Quit [Q]Quit Unchanged
setup>******************** ADVANCED SETUP MENU ***********************
[1]Auto Logout Time [2]Data Port
[5]Network Ping Test
[6]Accept IP Addr(1) [7]Accept IP Addr(2) [8]Accept IP Addr(3)
[9]Accept All IP Addr [0]Search Port
[!]Restore Default Setting
[Q]Return to Main Menu
advanced>