Sharp Xg Ph70x Projector Quickstart Guide
Here you can view all the pages of manual Sharp Xg Ph70x Projector Quickstart Guide. The Sharp manuals for Projector are available online for free. You can easily download all the documents as PDF.
Page 41
-41 Video Wall Projection Info •Before setting up the video wall projection, install Internet Explorer (version 5.0 or later). • Video wall is not compatible with resolutions higher than SXGA. • Image quality may deteriorate when picture signals are input through multiple projectors with an RGB cable or an RCA cable in a daisy chain connection. Hub Usually, a costly image-processing device is required to set up a video wall projection. This projector has built-in video wall capability that doesn’t...
Page 42
-42 Video Wall Projection Setting up the Video Wall Projection Basic Following is an example of how to build a 2 X 2 video wall using 4 projectors. Projector 1 Projector 2 Computer RGB cable RGB cable OUTPUT (FOR INPUT 1, 2) terminal INPUT 1 terminal INPUT 1 terminal OUTPUT (FOR INPUT 1, 2) terminal Projector 3 RGB cableINPUT 1 terminal OUTPUT (FOR INPUT 1, 2) terminal Projector 4 RGB cableINPUT 1 terminal
Page 43
-43 Video Wall Projection 1Access one of the four projectors via Internet Explorer. (See “Controlling the Projector Using Internet Explorer (Version 5.0 or later)” (page 23) for the details.) 2Click “Video Wall” on the menu. • “Video Wall” display will appear. 3Select “2 X 2” on “Division”. 1 2 3 4 1 1 1 1 1 Selects a position for each projector. (the assigning buttons) 2 2 2 2 2 Selects a number of positions where the video wall is divided. 3 3 3 3 3 Displays the current status for the video wall...
Page 44
-44 Video Wall Projection 12 3 4 5 6 7 8 9 1223 23 45 556 789 The numbers of the projector refer to the numbersof the projected positions. 123 456 789 1 2 3 4 5 6 7 8 9 The numbers of the projector refer to the numbersof the projected positions. Assigning the Projected Image on the Video Wall Setup Followings are examples for assigning the projected images for the front and rear projections. Front Projection Rear Projection Adjusting the Position Horizontally and Vertically Click “UP”, “DOWN”, “LEFT”...
Page 45
-45 Video Wall Projection Notes on the Wide Video Wall Projection Selecting “2 X 1”, “3 X 1”, “4 X1”, “5 X 1”, “6 X 1”, “7 X 1” or “8 X 1” on “Division” (see page 43) allows you to create the wide video wall. To create the wide video wall with three projectors lining up in single file from left to right (as shown above), select “3 X 1” on “Division”, select a position for each projector, and then input the image which width is compressed at 1/3 (as shown below).
Page 46
-46 Video Wall Projection INPUT 1 terminal Video equipment RGB cable RGB cable RGB cable RGB cable Projector 1 : Master Projector 2 : Slave Projector 3: Slave Projector 4 : Slave LAN terminal Computer ComputerINPUT 4 terminal INPUT 4 terminal INPUT 4 terminal INPUT 4 terminal 5 BNC to 15-pin D-sub cable LAN cable (straight-through type) INPUT 1 terminal INPUT 1 terminal INPUT 1 terminal INPUT 2 terminals OUTPUT (FOR INPUT 1, 2) terminal OUTPUT (FOR INPUT 1, 2) terminal OUTPUT (FOR INPUT 1, 2) terminal...
Page 47
-47 Video Wall Projection Projector 1:Master Projector 2: Slave Projector 3: Slave Projector 4: Slave LAN terminal Computer LAN cable LAN cable (straight-through type) Hub LAN terminal LAN terminal LAN terminal 1Change the TCP/IP settings for the computer as shown below. (See “Setting an IP Address for the Computer” on page 19 for the details.) •IP address : 192.168.150.2 •Subnet mask : 255.255.255.0 •Default gateway : (Do not input any values.) 2Change the TCP/IP settings for each projector as shown...
Page 48
-48 Video Wall Projection 4Turn on all of the projectors. 5Access the projector 1 from the computer via Internet Explorer. (See “Controlling the Projector Using Internet Explorer (Version 5.0 or later)” on page 23 for the details.) 6Click “Stack” on the menu. 7Select “Master” on “Stack Setting”. • “Slave Address” display will appear. 8Make the IP address for each pro- jector as shown below. • Slave 1 : 192.168.150.4 • Slave 2 : 192.168.150.5 • Slave 3 : 192.168.150.6 9Click the “Apply” button. 10Access...
Page 49
-49 Video Wall Projection Master Set Inputs ON ON OFF ON OFFON OFF OFF ON OFFINPUT1 INPUT2 INPUT3 INPUT4 INPUT5 Slave Set Inputs INPUT1 INPUT2 INPUT3 INPUT4 INPUT5 Projector 1 Projector 2-4 13Repeat the same procedure from the step 10 to 12 for the projector 3 and 4. 14Select inputs as specified in the table on the right. (See page 86 on the projector operation manual.) Note • Set input terminals you will use to “ON”. Set input terminals you will not use to “OFF”. 15T urn off all of the projectors....
Page 50
-50 1Click “Start” – “All Programs” – “Accessories” – “Communica- tions” – “HyperTerminal”. •If you do not have HyperTerminal in- stalled, see the operation manual of your computer. • Depending on the settings of your com- puter, you may be required to enter your area code and other details. Enter the information as required. 2Enter a name in the “Name” field, and click “OK”. 3If you are required to enter the area code, enter it in the “Area code” field. From the “Connect using” drop-down menu, select...