Sharp Xg Ph50x Projector User Manual

							Basic Operation
-47
Freezing a Moving
Image
1Press  on the remote control.
• The projected image is frozen.
2Press  again to return to the
moving image from the currently
connected equipment.
Selecting the Picture
Mode
Y ou can select the suitable picture mode for the
projected image, such as movie or video game.
Press  on the remote control.
• When pressing , the picture mode
changes in order of
Note
• Press  to return to the “STANDARD”
mode.
• This function can also be accessed from the
OSD menu (see page  60).
STANDARDPRESENTATIONCINEMACUSTOM
FREEZE button
PICTURE MODE
button
UNDO button
2Press  on the remote control
to cancel the operation.
• The magnification then returns to  ×1.
Note
In the following cases, the image will
return to the normal size ( ×1).
• When switching the input mode.
• When 
 has been pressed.
• When the input signal is changed.
•
When the input signal resolution and re-
fresh rate (vertical frequency) change.
• When  has been pressed. 
						

							-48
Resize Mode
Press  on the remote control.
•Pressing  changes the display as shown.
• To  return to the standard image, press 
 while
“ RESIZE ” is displayed on the screen.
• This function can also be accessed from the OSD
menu (see page  74).
This function allows you to modify or customize the resize mode to enhance the input image. Depend-
ing on the input signal, you can choose “NORMAL”, “FULL”, “\
DOT BY DOT”,  “BORDER”, “STRETCH”
or “SMART STRETCH” image.
COMPUTER
RESIZE button
Mouse/adjustment button 
(
' /" /\ /| )
UNDO button
4:3 aspect ratio
Other aspect ratios
SVGA (800  × 600)XGA (1024  × 768)SXGA (1280  × 960)UXGA (1600  × 1200)
SXGA (1280  × 1024) NORMAL
1024 
× 7681024  × 7681024  × 7681024  × 768
960  × 768 FULL
————
1024  × 768 DOT BY DOT
800 
× 600—1280  × 9601600  × 1200
1280  × 1024
Resolution lower than
XGA NORMAL FULL DOT BY DOT
4:3 aspect ratio
Output screen image
XGA
Resolution higher than XGA
• “NORMAL” is fixed when XGA (1024  × 768) signals are entered.
4:3 aspect ratio
4:3 aspect ratio
SXGA (1280  ×
× ×
×
×  1024)
: Cutout area on which images cannot be projected.
: Area where the signals are off screen.
Input signal
Computer Image type
Image Projection 
						

							Basic Operation
-49
VIDEO
: Cutout area on which images cannot be projected.
: Area on which the image is not included in the original signals.
SMART STRETCH1024  × 576*
—
—
480 I, 480P, 576 I, 576P,NTSC, PAL, SECAM540P
720P, 1035 I, 1080 I 4:3 aspect ratio,letter box, squeeze16:9 aspect ratio
16:9 aspect ratio NORMAL
1024  × 768—
— BORDER
768  × 576*—
— STRETCH
1024  × 576*
480 I,  480P,
576 I,  576P,
NTSC, PAL, SECAM 4:3 aspect ratio
Output screen image
Letter box
Squeeze
16:9 aspect ratio
SMART STRETCHNORMAL BORDER
STRETCH
16:9 aspect ratio
(4:3 aspect ratio in
16:9 screen)
16:9 aspect ratio
720P, 1035
I,  1080 I FULL
FULL
—
1024  × 768
—
540P
• “STRETCH” is fixed when 720P, 1035I or 1080I signals are entered.
* The “Digital Shift” function can be used with these images.
Input signalDTV/video Image type 
						

							-50
Displaying the Black
Screen
This function allows you to tempo-
rarily display the black screen.
1Press .
2Pressing  again will turn
the projected image back on.
Displaying and Setting
the Break Timer
This function allows you to show the re-
maining time for break during meeting.
1Press .
2While “”  is displayed, press
' , " , \  or  | to set the break
timer.
• You can set anywhere between 1 and
60 minutes (in 1 units).
• The break timer starts to count down as
soon as 
'
' '
'
' , 
"
" "
"
" , 
\
\ \
\
\  or 
|
| |
|
|  is pressed.
Note
•Pressing  will cancel the break timer.
• A uto Power Off function will be temporarily
disabled during the break timer.
When no input signal is detected for more
than 15 minutes, the projector will automati-
cally enter the standby mode if the break
timer has elapsed.
• The break timer will be displayed on the
startup image. To change the screen dis-
played during the break timer, change the
setting of “Startup Image” (see page  77).
• When “Slave” is set for “Stack Setting”, the
break timer is not displayed. (See page  84.)
▼Projected Image
▼On-screen Display
BLACK SCREEN 
button
Mouse/
adjustment 
button 
(
'/"/\/|) 
UNDO 
b utton
BREAK TIMER 
b
utton
Image Projection 
						

							Useful Features
-51
Menu Items
The following shows the items that can be set in the projector.
“Picture” menu
INPUT 1 / INPUT 2 / INPUT 3
+30
-30
+30
-30
+30
-30
+30
-30
+30
-30
+10
0
Signal Type Auto
RGB
ComponentINPUT 1/INPUT 2D.PC RGB
D.PC Comp.
D.Video RGB
D.Video Comp. INPUT 3
Tint Color
Reset Bright
+30
-30Contrast
Red
Green
Bright Boost
Progressive
Picture
4500K
10500K
Main Menu Sub Menu
CLR Temp
Page
 60
Page  61
Page 60
Page 60
Page  61
Page 62
Page 60
Page 63
Picture Mode Standard
Presentation
Cinema
Custom
*1
*1
*1
*1
*1
*1
*1
*3
*5 *1 *4
*2
2D Progressive
3D Progressive
Film Mode
Page 
62
DNR OFF
Level 1
Level 2
Level 3
+30
-30Blue
Page  64
C.M.S. Adjustment Standard
Custom 1
Custom 2
Custom 3
sRGB
+30
-30Sharp
Pressing   displays the items on the lower
part of the “Picture” menu.
*1 “Color”, “Tint”, “Red”, “Green”, “Blue”, “CLR Temp” and “Bright Boost” cannot be adjusted when “C. M. S. Adjust-
ment” is set to “sRGB”.
*2 “Sharp” can be adjusted only when 480
I, 480P, 540P, 576I, 576P, 720P, 1035I, or 1080I signal is input.
*3 “Progressive” can be adjusted only when 480
I  or 576I signal is input.
*4 “sRGB” can be selected under the conditions below.
• When “Signal Type” is set to “RGB”, “D. PC. RGB” or “D. Video RGB”
•  When “Signal Type” is set to “Auto” and the input signal is distinguished as “RGB”.
*5 “DNR” can be adjusted only when 480
I, 480P, 576I or 576P signal is input. 
						

							-52
Menu Items
INPUT 4 / INPUT 5
+30
-30
+30
-30
+30
-30
+30
-30
+30
-30
+10
0
Tint Color
Reset Bright
+30
-30Contrast
Red
Green
Bright Boost
Progressive
Picture
4500K
10500K
Main Menu Sub Menu
CLR Temp
Page
 60
Page  61
Page 60
Page 60
Page  61
Page 62
Page 60
Picture Mode Standard
Presentation
Cinema
Custom
2D Progressive
3D Progressive
Film Mode
Page 
62
DNR OFF
Level 1
Level 2
Level 3
+30
-30Blue
Page  64
C.M.S. Adjustment Standard
Custom 1
Custom 2
Custom 3
+30
-30Sharp
Pressing   displays the items on the lower
part of the “Picture” menu.
“Picture” menu 
						

							Useful Features
-53
“Fine Sync” menu
*6 The “Fine Sync” menu is displayed only while the input mode is INP\
UT 1, INPUT 2 or INPUT 3.
*7 “Clock”, “Phase”, “H-Pos”, “V-Pos”, “Reset”, “Save Setting”, “Select Setting” and “Special Modes” can be ad-justed only while the input mode is INPUT 1 or INPUT 2.
Fine Sync
+15
-15
+30
-30
+30
-30
+30
-30Clock
Phase
H-Pos
V-Pos
Reset
Auto Sync Disp Save Setting
Main Menu
Auto Sync
Page  68
Page
 68
Page  68
Page  70
*6
*7
Page  71
OFF
Normal
High Speed
Select SettingPage  69Special ModesPage  69Signal InfoPage  70
Sub Menu
“C.M.S.” menu
View Settings
Reset (This Color)
C.M.S.
Main Menu
Page
 64Page  64
Page  66
Page  67
C.M.S. Adjustment Standard
Custom 1
Custom 2
Custom 3
sRGB
Page
 66
Reset (All Colors)
[R] Red
[Y] Yellow
[G] Green
[C] Cyan
[B] Blue
[M] MagentaTarget
Page  64
+30
-30
+30
-30
+30
-30Lightness
Chroma
Hue
Page  66
Page  65
Page  65
Sub Menu 
						

							-54
Menu Items
“Options (1)” menu
INPUT 4 / INPUT 5
INPUT 1 / INPUT 2 / INPUT 3
Pict in Pint
Options (1)
Main Menu Sub Menu
OSD Display
Auto
PAL (50/60Hz)
SECAM
NTSC4.43
NTSC3.58
PAL-M
PAL-N
Video System
Background
Image CaptureSave Image
Delete
Logo
Custom
Blue
None
Normal
Full
Dot By Dot
When inputting RGB 
signalNormal
Full
Border
Stretch
Smart Stretch
When inputting DTV/video 
signal
Eco Mode [ON/OFF]
Auto Search [ON/OFF]
System Lock
Auto Power Off [ON/OFF]
Page  74
Page  75
Page
 74
ResizePage  74
Page  76
Page  76
Page  77
Page  78
Page  78
Page  79
Page  79
*9 *8
*8
Digi. ShiftPage  75
Normal
Level A
Level B
Startup Image Logo
Custom
NonePage
 77
+96
-96
“Audio” menu
+30
-30
+30
-30
+30
-30
Speaker [ON/OFF] Bass Treble
+30
-30Balance
Reset
Audio Out
Audio
Main Menu
Page
 72
Page  72
Page  72
Page  73
FAO
VAO
Sub Menu
*8 Item when inputting RGB signal through INPUT 1, INPUT 2 or INPUT 3
*9 Item when selecting INPUT 4 or INPUT 5 
						

							Useful Features
-55
“Language” menu
“Status” menu
Main MenuSub Menu
English
Deutsch
Español
Nederlands
Français
Italiano
Svenska
PortuguêsLanguage
Page 89
Status
Main menu
Page  89
“Options (2)” menu
LAN/RS232C
Monitor Out
RS-232C
Options (2)
Enable
Disable
INPUT 1 [ON/OFF]
INPUT 2 [ON/OFF]
INPUT 3 [ON/OFF]
INPUT 4 [ON/OFF]
INPUT 5 [ON/OFF]
9600 bps
38400 bps
115200 bps
Enable
Disable
Main Menu Sub Menu
Set Inputs
Page  82Page  82
Page  86
Page  86
Service Mode
Page  88
Page  87
Page  87
All Reset
Password Old Password
New Password
Reconfirm
Lamp 1
Lamp 2Lamp Timer (Life)
Page
 83Both Lamps
Lamp 1 Only
Lamp 2 Only
Equal UseLamp Mode
Page  83
Front
Ceiling + Front
Rear
Ceiling + RearPRJ Mode
Page  84
Page  84
Stack Setting Normal
Master
Slave
Pair Stack
Page
 85
Page  85
Keylock Level Normal
Level A
Level B
Page
 88 
						

							-56
Menu items
The menu can be operated to achieve two functions, adjustments and settings. (For setting
the menu items, see pages 58 and  59. )
Using the Menu Screen
Menu Selections (Adjustments)
Example: Adjusting “Bright”
•This operation can also be performed by using the buttons on the projector. ENTER 
button
MENU button
UNDO button
Mouse/ 
adjustment
button (
'/" /\ /| )
Adjustment 
buttons ( '/" /\ /| )
MENU button
UNDO button
ENTER button
Example: “Picture” screen menu for
INPUT 1 (RGB) mode1Press .
•The “Picture” menu screen for the se-
lected input mode is displayed.
2Press 
\
\ \
\
\  or 
|
| |
|
|  to display the other
menu items.
• There are eight menu items as shown
below.
Note
•The “Fine Sync” menu is not available
for selecting INPUT 4 or INPUT 5.
Menu item