Sharp Xg P560w N Projector User Manual

							Useful Features
-49
Picture Adjustment (“Picture” menu)
1 11 1
1 Selecting the Picture Mode
This function allows you to select the picture
mode in accordance with brightness of the room
or content of the image to be projected.
In all picture modes, items on the “Picture” menu
can be adjusted and saved.
Note
•You can also press PICTURE MODE on the re-
mote control to select the picture mode. (See
page 38.)
2 22 2
2 Adjusting the Image
Select a picture mode before adjusting the im-
age.
*1 “Color”, “Tint”, “Red”, “Green” and “Blue” cannot
be adjusted when “C.M.S. Adjustment” on the
“C.M.S.” menu is set to “sRGB”. (See page 52.)
*2“Sharp” can be adjusted only when 480I, 480P,
540P, 576I, 576P, 720P, 1035I, 1080I or 1080P
DTV signal is input during the COMPUTER1/2,
DVI, HDMI mode; or the input mode is set to
VIDEO or S-VIDEO.
Note
•To reset all adjustment items, select “Reset” and
press ENTER.
|  | |  | 
| Page 1
Selectable itemsStandard
Presentation
Movie
Custom
DescriptionFor standard image
Brightens darker portions of image for
more enhanced presentations.
Gives greater depth to darker portions
of image for a more exciting theater
experience.
The factory preset value is the same as
the one of “Standard”.
Using the dedicated software “Sharp
Gamma Manager” allows you to adjust
the gamma curve.
Visit “http://sharp-world.com/projector/”
for details.
Selectable itemsPress 
\ \\ \
\Press 
| || |
|
Contrast
BrightColor*1
Tint*1
Red*1
Green*1
Blue*1
Sharp*2
For less contrast
For less brightnessFor less color intensity
For making skin tones
purplish
For weaker red
For weaker green
For weaker blue
For less sharpness
For more contrast
For more brightnessFor more color intensity
For making skin tones
greenishFor stronger red
For stronger green
For stronger blue
For more sharpness
Menu operation  Page 47
|  | |  | 
| Page 2
2 1
6
7
8
3
4
5 2 1
6
7
8 
						

							-50
3 33 3
3 Adjusting the Color Temperature
Note
•“CLR Temp” cannot be set when “C.M.S. Ad-
justment” on the “C.M.S.” menu is set to “sRGB”.
(See page 52.)
4 44 4
4 Selecting the Progressive Mode
*The film source is a digital video recording with the original
encoded as is at 24 frames/second. The projector can con-
vert this film source to progressive video at 60 frames/sec-
ond with NTSC and PAL60Hz or at 50 frames/second with
PAL50Hz and SECAM to play back a high-definition image.
Note
•In NTSC or PAL60Hz, even if the 3D Progressive
mode has been set, the three-two pull down enhance-
ment will be enabled automatically when the film
source has been entered.
•When the image is blurred or noisy, switch to the
optimal mode.
•When using progressive inputs, inputs are directly
displayed so that “2D Progressive”, “3D Progressive”
and “Film Mode” cannot be selected.
Menu operation  Page 47
Selectable items4500K
10500KDescription
For lower color temperature for warmer,
reddish incandescent-like images.
For higher color temperature for cooler,
bluish, fluorescent-like images.
DescriptionUseful to display fast-moving images such
as sports and action films.
Useful to display relatively slowmoving
images such as drama and documentary
more clearly.
Reproduces the image of film source*
clearly. Displays the optimized image of film
transformed with three-two pull down (NTSC
and PAL60Hz) or two-two pull down
(PAL50Hz and SECAM) enhancement to
progressive mode images.
Selectable items2D
Progressive
3D
Progressive
Film Mode
5 55 5
5 Reducing Image Noise (DNR)
Video digital noise reduction (DNR) provides high
quality images with minimal dot crawl and cross
color noise.
Note
•Set a level so as to view a clearer picture.
Make sure to set “DNR” to “Off” in the
following cases:
•When the image is blurry.
•When the contours and colors of moving im-
ages drag.
•When TV broadcasts with weak signals are pro-
jected.
Info
•This function is available for all signals with
VIDEO or S-VIDEO.
•This function is available for 480I, 480P, 576I
and 576P signals with COMPUTER1/2, DVI or
HDMI.
DescriptionDNR does not function.
Sets the DNR level.
Selectable items
Off
Level 1–3
Picture Adjustment (“Picture” menu) 
						

							Useful Features
-51
Description
Automatically selects the appropriate
input signal between RGB and Compo-
nent.Set when RGB signals are received.
Set when component signals are
received.
Selectable items
Auto
RGB
Component
Description
Set when digital PC RGB signals are
received from the computer.
Set when digital PC component signals
are received from the computer.
Set when digital video RGB signals are
received from video equipment.Set when digital video component signals
are received from video equipment.
Selectable items
D. PC RGB
D. PC Comp.
D. Video RGB
D. Video Comp.
6 66 6
6 Selecting the Signal Type
When using an input mode other than S-VIDEO or
VIDEO input, set the signal type setting to the cor-
responding input signal type (RGB or Component).
■When COMPUTER1/2 is selected for the input
mode
■When DVI is selected for the input mode
■When HDMI is selected for the input mode
This function sets the type of picture signal input from
HDMI-compatible equipment.
7 77 7
7Selecting the Dynamic
Range
An optimum picture may not be displayed if a DVI-D
or HDMI capable device’s output signal type and
the projector’s input signal type do not match. If this
should occur, switch the “Dynamic Range”mode.
8 88 8
8 Selecting the Color Space
This function select the color space for signals in-
put from a DVI-D- or HDMI-compatible device.
Description
In most circumstances, “Auto” should
be selected.
When the black levels of the image
show banding or appear faded, select
the item that results in the better picture
quality.
Selectable items
Auto
Standard
Enhanced
Description
In most circumstances, “Auto” should
be selected.
Select the item that results in the better
picture quality.
Selectable items
Auto
ITU601
ITU709
Menu operation  Page 47
Description
Automatically set the RGB or compo-
nent signal when digital video signals
are received from video equipment.
Set when digital video RGB signals are
received from video equipment.
Set when digital video component signalsare received from video equipment.
Set when digital PC RGB signals are
received from the computer.
Set when digital PC component signals
are received from the computer.
Selectable items
D. Video Auto
D. Video RGB
D. Video Comp.
D. PC RGB
D. PC Comp. 
						

							-52
Color Management System (“C. M. S.” menu)
1 11 1
1Selecting the Color
Reproduction Mode
This function allows you to select the color re-
production mode for the projected images.
Note
•sRGB is an international standard of color repro-
duction regulated by the IEC (International
Electrotechnical Commission). As the fixed color
area has been decided by the IEC, the images are
displayed in a natural tint based on an original im-
age, when “C.M.S. Adjustment” is set to “sRGB”.
•You cannot set “Color”, “Tint”, “Red”, “Green”,
“Blue”, “CLR Temp” on the “Picture” menu, when
“C.M.S. Adjustment” is set to “sRGB”.
•For additional information about the sRGB func-
tion, visit “http://www.srgb.com/”.
Info
•When “C.M.S. Adjustment” is set to “sRGB”, the
projected image may become dark, but this
does not indicate a malfunction.
2 22 2
2 Selecting the Target Color
This function allows you to select the target color
for adjusting the display characteristics.
3 33 3
3Setting the Brightness of
the Target Color
This function allows you to set the brightness of
the selected target color.
4 44 4
4Setting the Chromatic
Value of the Target Color
This function allows you to set the chromatic
value of the selected target color.
5 55 5
5 Setting the Hue of the
Target Color
This function allows you to set the hue of the
selected target color.
6 66 6
6 Resetting User-defined
Color Settings
This function allows you to reset the specific tar-
get color or all of the six colors.
7 77 7
7 Overview of All Color Settings
This function allows you to confirm the settings
of all the colors.
For more brightness of the
target color For less brightness of the
target color
Press \Press |
For more chromatic value of
the target color For less chromatic value of
the target color
Press \Press |
Menu operation  Page 47
1
2
3
4
5
6
7
For stronger yellow of the
target color For stronger red of the
target color
Press \Press |
Description
“Lightness”, “Chroma” and “Hue” of
the color selected for “Target” are
reset.
“Lightness”, “Chroma” and “Hue” of
all colors are reset.
Selectable items
Reset (This Color)
Reset (All Colors)
RedCyan
YellowBlue
GreenMagenta
Selectable itemsStandard
Custom 1 – 3
sRGB
DescriptionStandard settings
“Lightness”, “Chroma” and “Hue” can be
adjusted for each of the six colors.
A natural tint based on an original im-
age from the computer. 
						

							Useful Features
-53
Computer Image Adjustment (“Fine Sync” menu)
1 11 1
1 Adjusting the Computer
Image
Use the Fine Sync function in case of irregulari-
ties such as vertical stripes or flickering in por-
tions of the screen.
Note
•You can automatically adjust the computer im-
age by setting “Auto Sync” on the “Fine Sync”
menu to “Normal” or “High Speed”, or by press-
ing AUTO SYNC on the projector or on the re-
mote control. See page 54 for details.
•To reset all adjustment items, select “Reset” and
press ENTER.
Selectable itemsClock
Phase
H-Pos
V- Po s
DescriptionAdjusts vertical noise.
Adjusts horizontal noise (similar to
tracking on your VCR).
Centers the on-screen image by
moving it to the left or right.
Centers the on-screen image by
moving it up or down.
2 22 2
2 Saving Adjustment Settings
This projector allows you to store up to seven
adjustment settings for use with various com-
puters.
3 33 3
3 Accessing Adjustment
Settings
Adjustment settings stored in the projector can
be easily accessed.
Note
•If a memory has not been set, the resolution
and frequency setting will not be displayed.
•When selecting a stored adjustment setting with
“Select Setting”, you can set the projector in the
stored adjustments.
4 44 4
4 Setting the Resolution
Ordinarily, the type of input signal is detected
and the correct resolution mode is automatically
selected. However, for some signals, the optimal
resolution mode in “Resolution” on the “Fine
Sync” menu may need to be selected to match
the computer display mode.
Note
•If your computer displays patterns which repeat
every other line (horizontal stripes), flickering
may occur which makes the image hard to see.
•See “Checking the Input Signal” on page 54 for
information on the currently selected input sig-
nal.
11
2
3
4
5
6
7
Menu operation  Page 47 
						

							-54
5 55 5
5 Checking the Input Signal
You can check the input signal information.
6 66 6
6 Auto Sync Adjustment
Used to automatically adjust a computer image.
Note
•Auto Sync adjustment is also performed by
pressing AUTO SYNC on the projector or on
the remote control.
•The Auto Sync adjustment may take some time
to complete, depending on the image of the
computer connected to the projector.
•When the optimum image cannot be achieved
with Auto Sync adjustment, use manual adjust-
ments. (See page 53.)
•When AUTO SYNC is pressed while “Auto
Sync” is “High Speed” or “Off ”, Auto Sync will
be executed in “High Speed” mode. If the but-
ton is pressed again within one minute, Auto
Sync will be executed in “Normal” mode.
Computer Image Adjustment (“Fine Sync” menu)
Selectable items
Off
Normal
High Speed
Description
Auto Sync adjustment is not automati-
cally performed.
Auto Sync adjustment will occur when
the projector is turned on or when the
input signals are switched, when
connected to a computer.
“Normal” takes more time than “High
Speed” for more accurate Auto Sync
adjustment.
7 77 7
7 Setting the Auto Sync
Display Function
Used to set the display during Auto Sync.
Description
The image set as a background image
is projected. See page 58.
The computer image being adjusted is
displayed.
Selectable items
Background
Adjusting Disp.
Menu operation  Page 47 
						

							Useful Features
-55
Audio Adjustment (“Audio” menu)
1 11 1
1 Adjusting the Audio
This function allows you to adjust the projector’s
audio.
Note
•To reset all adjustment items, select “Reset” and
press ENTER.
2 22 2
2 Setting the Audio Output Type
This function determines whether the audio level
output from the AUDIO OUTPUT terminal is fixed
or variable by linking with VOLUME.
Info
•When “Audio Out” has been set to “VAO”, first
make sure to lower the volume of the projector
before turning the power on or off and when
switching the input.
Note
When the projector is connected to audio equipment:
•It is recommended that “FAO” be selected on “Audio
Out”. Because the audio signal from the audio equip-
ment does not vary in strength with the volume level
of the projector, you can enjoy better sound.
•When “FAO” is selected on “Audio Out”, video and
audio may not synchronize.
-When connecting audio equipment that has a
function for adjusting audio delay time, adjust
the delay time for synchronizing video and au-
dio.
-When the audio equipment does not have such
a function and the unsynchronized video and au-
dio bothers you, select “VAO” on “Audio Out”.
Selecting “VAO” synchronizes video and audio
automatically.
•The HDMI audio will not output from the
MONITOR OUT AUDIO terminal when the pro-
jector is in the standby mode.
3 33 3
3 Setting the Speaker
This function allows you to turn the audio out-
put of the internal speaker on or off when the
projector is connected to an external amplifier.
Note
•The HDMI audio will not output from the
MONITOR OUT AUDIO terminal when the pro-
jector is in the standby mode.Description
Audio output that does not vary in
strength with the volume level of the
source projector.
Audio output that varies in strength with
the volume level of the source projec-
tor.
Selectable items
FAO
(Fixed Audio
Output)
VA O
(Variable
Audio Output)
Increased audio from
the right speaker
For stronger treble
For stronger bass
Balance
Treble
BassIncreased audio from
the left speaker
For weaker treble
For weaker bass
Selectable itemsPress \Press |
Selectable items
On
OffDescription
The audio signal is output from the internalspeaker.
The audio signal is not output from the
internal speaker.
1
2
3
Menu operation  Page 47 
						

							-56
Using the “Options 1” Menu
1 11 1
1 Displaying Dual Pictures
(Pict in Pict)
The Pict in Pict (picture in picture) function al-
lows you to display two pictures on the same
screen. You can display the image input from
VIDEO or S-VIDEO as an inset picture overlap-
ping the main picture input from COMPUTER1/2,
DVI or HDMI.
Note
•You can press ' / " / \ / | on the projector or
on the remote control to change the location of
the inset picture image.
(The inset picture frame will be displayed. To dis-
play the inset picture to the desired position, move
the frame and press ENTER on the projector or
on the remote control.)
•When “On” is selected, INPUT and VOL on the
projector will function as location shift button for
the inset picture.
•Inset picture can only be displayed in compos-
ite video or S-video signal of NTSC/PAL/
SECAM.
•The audio of the inset picture will come out of
the projector’s speakers.
•While the “Pict in Pict” function is working, the
“FREEZE” function only works for the inset
picture.
•The “Pict in Pict” function does not work when
the following signals are input to the main
picture.
−UXGA/SXGA+/SXGA/WXGA signal
−480I/480P/540P/576I/576P/720P/1035I/1080I/
1080P signal
−Interlaced RGB signal
−
All signals (when “Resize” is set to “Dot by Dot”)
−No signal (or when the resolution or refresh rate
(vertical frequency) of the signal is changed)
2 22 2
2 Setting the Resize Mode
Depending on the input signal, you can select
the screen image.
Note
•For details of the Resize mode, see pages 39
and 40.
•You can also press RESIZE on the remote con-
trol to change the Resize mode. (See page 39.)
Menu operation  Page 47 COMPUTER1/2, DVI, HDMI
2
3
4
6
7
8
9
0
q
w 1
VIDEO, S-VIDEO
3
4
5
7
8
9
0
q
w 2
When inputting RGB signal
Normal
FullDot By Dot
StretchWhen inputting HDMI/
DTV/video signal
Normal
Area ZoomV-Stretch
Stretch
Smart Stretch 
						

							Useful Features
-57
5 55 5
5 Setting the Video System
The video input system mode is factory preset
to “Auto”; however, a clear picture from the con-
nected audio-visual equipment may not be re-
ceived, depending on the video signal difference.
In that case, switch the video signal.
Note
•The video signal can only be set in VIDEO or
S-VIDEO mode.
•When “Video System” is set to “Auto”, you may
not receive a clear picture due to signal differ-
ences. Should this occur, switch to the video
system of the source signal.
•While “Video System” is set to “Auto”, when
PAL-M or PAL-N signal is input, the image from
PAL signal will be displayed.
6 66 6
6 Capturing Projected Images
This projector allows you to capture projected
images (RGB signals) and set them as a startup
image, or background image when no signals are
being received.
Note
•Images can be captured only when they are from
WXGA (1280 × 800) non-interlace signals in
COMPUTER1/2, DVI or HDMI mode with
“RESIZE” set to “Normal”.
•The saved image is reduced to 256 colors.
•Images from equipment connected to VIDEO
or S-VIDEO terminal cannot be captured.
•Only one image can be captured and saved.
•The color of images may differ before and after
saving if an image is captured on which image
adjustment has been performed using the
“C.M.S.” function.
•To delete the captured image, select “Delete”,
and then press ENTER.
DescriptionWhen connected to PAL video equipment.
When connected to SECAM video equipment.
When reproducing NTSC signals in PALvideo equipment.
When connected to NTSC video equipment.
Selectable items
PAL (50/60 Hz)SECAM
NTSC4.43
NTSC3.58
3 33 3
3 Shifting the Projected
Image Vertically (Digital
Shift)
For easier viewing, this function shifts the im-
age projected on the screen up or down elimi-
nating either the upper or lower black band found
in 16:9 and other wide aspect ratios.
Note
•This function will not work depending on the type
of resize mode. See pages 39 and 40 for details.
4 44 4
4 Setting On-screen Display
This function allows you to turn the on-screen
messages on or off.
Note
•When “Keylock Level” is set to “Level A” or “Level
B”, pressing STANDBY displays “All buttons on
Projector are locked.” regardless of  the “OSD
Display” setting.
Press \
Shifts the projected image
down.Press |
Shifts the projected image
up.
Menu operation  Page 47
Description
All on-screen displays are displayed.
INPUT/VOLUME/MUTE/FREEZE/AUTO
SYNC/MAGNIFY/ “An invalid button has
been pressed.” are not displayed.
All on-screen displays are not displayed (ex-
cept the menu, H&V LENS SHIFT, KEY-
STONE, FOCUS, ZOOM, “All buttons on Pro-
jector are locked.” and warning displays).
Selectable items
NormalLevel A
Level B 
						

							-58
Using the “Options 1” Menu
7 77 7
7 Selecting the Background
Image
Note
•When “Custom” is selected, an image saved us-
ing “Image Capture” can be displayed as a back-
ground image.
8 88 8
8Selecting the Startup Image
Note
•When “Custom” is selected, an image saved
using “Image Capture” can be displayed as a
startup image.
9 99 9
9Setting the Eco Mode
When the two lamps are lit at the same time
* This is a reference value and is not guaranteed.
Note
•When “Eco Mode” is set to “On”, the power con-
sumption will decrease and the lamp life will
extend.
Selectable items
Logo
Custom
Blue
NoneDescription
Default image
User customized image (e.g. company logo)
Blue screen
Black screen
0 00 0
0Detecting the Input
Signals Automatically
Note
•While the “Auto Search” function is detecting
the input signal, pressing a button on the pro-
jector or the remote control stops the “Auto
Search” function. After the “Auto Search” func-
tion finishes completely, press the desired button.
q qq q
q Setting the Auto Power
Off Function
Note
•When “Auto Power Off ” is set to “On”, 5 min-
utes before the projector enters the standby
mode, the message “Enter STANDBY mode in
X min.” will appear on the screen to indicate
the remaining minutes.
Selectable items
Logo
Custom
NoneDescription
Default image
User customized image (e.g. company logo)
Black screen
Brightness
Approx.
77%
100%
Selectable items
On
Off
Power consumption (When
using AC 100V)
82%
100%Lamp lifeApprox.
3,000 hours*
Approx.
2,000 hours*
Selectable items
On
OffDescription
Automatically searches for and switches to
the input mode in which signals are being
received.
“Auto Search” does not function.
Description
The projector automatically enters the
standby mode when no input signal is
detected for 15 minutes or longer.
The “Auto Power Off ” function will be
disabled.
Selectable items
On
Off
Menu operation  Page 47