Sharp Xg P560w N Projector User Manual

							Introduction
-9
Ensure that you read the following safeguards when
setting up your projector.
Caution concerning the lamp unit
■Potential hazard of glass particles if lamp rup-
tures. In case of lamp rupture, contact your
nearest Sharp Authorized Projector Dealer
or Service Center for replacement. See
“Regarding the Lamp” on page 71.
Caution concerning the setup of the pro-
jector
■For minimal servicing and to maintain high
image quality, SHARP recommends that this
projector be installed in an area free from hu-
midity, dust and cigarette smoke. When the
projector is subjected to these environments,
the vents and lens must be cleaned more
often. As long as the projector is regularly
cleaned, use in these environments will not
reduce the overall operation life of the unit.
Internal cleaning should only be performed
by a Sharp Authorized Projector Dealer or
Service Center.
Do not set up the projector in places ex-
posed to direct sunlight or bright light.
■Position the screen so that it is not in direct
sunlight or room light. Light falling directly on
the screen washes out the colors, making
viewing difficult. Close the curtains and dim
the lights when setting up the screen in a
sunny or bright room.
The projector may be safely tilted to a
maximum angle of 9 degrees.
■Placement should be within 9 degrees of
horizontal.
If you have application requiring tilt angle
exceeding 9 degrees, please check with your
local Sharp sales office.
When using the projector in high-altitude
areas such as mountains (at altitudes of
approximately 1,500 meters (4,900 feet)
or more)
■When you use the projector in high-altitude
areas with thin air, set “Fan Mode” to “High”.
Neglecting this can affect the longevity of the
optical system.
Warning about placing the projector in a
high position
■When placing the projector in a high posi-
tion, make certain it is carefully secured to
avoid personal injury caused by the projec-
tor falling down.
Do not subject the projector to hard im-
pact and/or vibration.
■Take care with the lens so as not to hit or
damage the surface of the lens.
Rest your eyes occasionally.
■Continuously watching the screen for long
hours will cause eye strain. Take regular
breaks to rest your eyes.
Avoid locations with extremes of tem-
perature.
■The operating temperature of the projector
is from 41°F to 104°F (+5°C to +40°C).
■The storage temperature of the projector is
from –4°F to 140°F (–20°C to +60°C). 
						

							-10
Using the projector in other countries
■The power supply voltage and the shape of
the plug may vary depending on the region
or country you are using the projector in.
When using the projector overseas, make
sure you use an appropriate power cord for
the country you are in.
Temperature monitor function
■If the projector starts to over-
heat due to setup problems or
blockage of the air vents, “
”
and “
” will illuminate in
the lower left corner of the picture. If the tem-
perature continues to rise, the lamp will turn off,
the temperature warning indicator on the pro-
jector will blink, and after a 90-second cooling-
off period the projector will enter the standby
mode. Refer to “Maintenance Indicators” on
page 69 for details.
Info
•The cooling fan regulates the internal tem-
perature, and its performance is automati-
cally controlled. The sound of the fan may
change during projector operation due to
changes in the fan speed. This does not
indicate malfunction.
•Even if you unplug the power cord after
projector operation, the cooling fan con-
tinues to run for a while. When you place
the projector into the storage case, make
sure that the cooling fan has stopped.
Optional lens installation
■For installing an optional lens, refer to “At-
taching the Optional Lens” on page 
77 or the
lens installation manual (supplied with the
optional lens).
■Remove the optional lens when carrying the
projector. Carrying the projector with an op-
tional lens attached can cause the projector
to be damaged by vibration or other factors.
Do not block the intake and exhaust
vents.
■Allow at least 11 13/16 inches (30 cm) of space
between the exhaust vent and the nearest
wall or obstruction.
■Set up the projector where air will not stay
near its exhaust vent. In order to avoid allow-
ing the heat from the exhaust vent to enter
the intake vent area, leave at least more than
11 
13/16 inches (30 cm) of space between the
intake vent and the surrounding walls or ob-
jects.
■If the cooling fan becomes obstructed, a pro-
tection circuit will automatically put the pro-
jector into standby mode to prevent overheat
damage. This does not indicate a malfunc-
tion (See pages 69 and 70.). Remove the pro-
jector power cord from the wall outlet and wait
at least 10 minutes. Place the projector where
the intake and exhaust vents are not blocked,
plug the power cord back in and turn on the
projector. This will return the projector to the
normal operating condition.
Caution regarding usage of the projector
■When using the projector, take care not to subject
it to hard impact and/or vibration, as this can result
in damage. Take extra care with the lens. If you are
not to use the projector for a long time, make cer-
tain you unplug the power cord from the wall outlet,
and disconnect any other cables connected to it.
■Do not carry the projector by holding the lens.
■When storing the projector, ensure you at-
tach the lens cap or dustproof cap to the pro-
jector. (See page 13.)
■Do not expose the projector to direct sunlight
or near heat sources. The projector may
change color or become deformed.
Other connected equipment
■When connecting a computer or other audio-
visual equipment to the projector, make the
connections AFTER unplugging the power
cord of the projector from the AC outlet and
turning off the equipment to be connected.
■Please read the operation manuals of the pro-
jector and the equipment to be connected for
instructions on how to make the connections.
IMPORTANT SAFEGUARDS 
						

							Introduction
-11
Accessories
Two R-6 batteries
(“AA” size, UM/SUM-3, HP-7 or similar)
Po wer cord
*
For U.S., Canada, etc.
(6 (1.8 m))
 F
or Europe, except U.K.
(6 (1.8 m))

*Use the power cord that corresponds to the wall outlet in your country.
•Projector manual and technical
reference CD-ROM

• Operation manual (this manual)

(1)
(2) (3) (4)
Lens cap
 (Only supplied with XG-P560W)

Dustproof cap
(Only supplied with XG-P560W-N)

Supplied accessories
RGB cable
(10 (3.0 m))
 F
or U.K., Hong Kong
and Singapore
(6 (1.8 m))
 F
or Australia, New
Zealand and Oceania
(6 (1.8 m))

Remote control

■ Lamp unit AN-P610LP
■ Ceiling-mount adaptor AN-P610T
■ Ceiling-mount unit AN-TK201
AN-TK202
■ Remote receiver AN-MR2
■ 3 RCA to mini D-sub 15 pin cable (10
 (3.0 m)) AN-C3CP2
Note
•Some of the optional accessories may not be available depending on the region. Please check with your
nearest Sharp Authorized Projector Dealer or Service Center.
Optional accessories
Note
•Codes in “<  >” are Replacement parts codes.
• When the lens is attached, use the lens cap supplied with the lens.
• You can attach the dustproof cap to the projector only when no lens is at\
tached. (Do not attach the
dustproof cap when the lens is attached.) 
						

							-12
Accessories
Optional lenses
No lens is attached to XG-P560W-N. The standard zoom lens is attached to XG-P560W.
The optional lenses from Sharp are also available for specialized application. Please see
your nearest Sharp Authorized Projector Dealer for details on all the lenses. (Refer to the
lens operation manual when using a lens.)
Throw Distance
The graph below is for 100-inch (254 cm) screen with 16:10 normal mode.
Screen
5101520253035 455040 (ft)
Standard zoom lens (AN-P18EZ : Standard equipment with XG-P560W)1210 – 161 (3.9 m – 4.9 m)
Throw distance ratio 1:1.8–2.25 Fixed wide lens (AN-P8EX)
59 (1.7 m)
Throw distance ratio 1:0.8
Tele-zoom lens (AN-P23EZ)
161 – 216 (4.9 m – 6.5 m)
Throw distance ratio 1:2.25–3.00
Tele-zoom lens (AN-P30EZ)
216 – 323 (6.5 m – 9.8 m)
Throw distance ratio 1:3.0–4.5
Tele-zoom lens (AN-P45EZ)
323 – 501 (9.8 m – 15.3 m)
Throw distance ratio 1:4.5–7.0
Wide-zoom lens (AN-P15EZ)
109 – 1210 (3.3 m – 3.9 m)
Throw distance ratio 1:1.5–1.8 Fixed wide lens (AN-P12EX)
87 (2.6 m)
Throw distance ratio 1:1.2
■LensProjection distance for 100 screen size
Fixed wide lens (× 0.8) AN-P8EX 59 (1.7 m)
Fixed wide lens (× 1.2) AN-P12EX 87 (2.6 m)
Wide-zoom lens (× 1.5 – 1.8) AN-P15EZ 109 – 1210 (3.3 m – 3.9 m)
Standard zoom lens (× 1.8 – 2.25) AN-P18EZ 1210 – 161 (3.9 m – 4.9 m)
(attached to XG-P560W)
Tele-zoom lens (× 2.25 – 3.0) AN-P23EZ 161 – 216 (4.9 m – 6.5 m)
Tele-zoom lens (× 3.0 – 4.5) AN-P30EZ 216 – 323 (6.5 m – 9.8 m)
Tele-zoom lens (× 4.5 –7.0) AN-P45EZ 323 – 501 (9.8 m – 15.3 m) 
						

							Introduction
-13
30
69
69
5572
69
55
16
66
77
69
30
77
28
28
31
31
54
41
3032
36
47
36
47
47
47
SHUTTER buttons• OPEN: For opening the shutter.
• CLOSE: For closing the shutter
 and hiding the projected
image.
Lamp unit cover
Attaching the lens cap/dustproof capSnap on the lens cap/dustproof cap 
straight.
Removing the lens cap/dustproof capPull the lens cap/dustproof cap directly 
outward.
STANDBY buttonFor putting the projector 
into standby mode.
ON buttonFor turning the power on.
ZOOM buttonsFor adjusting the projected 
image size.
FOCUS buttonsFor adjusting the focus.
Power indicator H&V LENS SHIFT button
For shifting the lens horizontally 
and vertically.
AUTO SYNC buttonFor automatically 
adjusting images when 
connected to a computer.
ENTER buttonFor setting items selected 
or adjusted on the menu.
KEYSTONE buttonFor entering the Keystone 
Correction mode.
Adjustment buttons 
('/"/\/|)
For selecting menu items 
and other settings.
INPUT buttonsFor switching input mode.
Volume buttonsFor adjusting the speaker 
sound level.
Temperature warning 
indicator Lamp 2 indicatorLamp 1 indicatorMENU button
For displaying adjustment 
and setting screens.
UNDO buttonFor undoing an operation or 
returning to the previous display.
Remote control sensor Speaker
Lens cover Lens cover removal button Speaker
Exhaust vent
Adjustment foot 
(on the bottom of the projector) Adjustment foot 
(on the bottom of 
the projector)
Projector
Part Names and Functions
Numbers in  refer to the main pages in this operation manual where the topic is explained.
Rear View
Front View 
						

							-14
Part Names and Functions
Projector (Rear View)
Using the Kensington Lock
•This projector has a Kensington Security Standard connector for use with a Kensington MicroSaver Security
System. Refer to the information that came with the system for instructions on how to use it to secure the
projector.
Numbers in  refer to the main pages in this operation manual where the topic is explained.
17
26
28
Remote control sensor16
24
25
24
25
67
68
24
25
24
25
27
27
26
26
COMPUTER/COMPONENT 2 
terminals
BNC terminals for computer 
RGB and component signals 
and audio input terminal.
WIRED REMOTE terminalFor connecting the remote control 
to the projector when the signals 
from the remote control cannot 
reach the remote control sensor.
LAN terminalTerminal for controlling the 
projector using a computer 
via network.
RS-232C terminalTerminal for controlling the 
projector using a computer.
S-VIDEO input terminalsTerminals for connecting video 
equipment with an S-video 
terminal and audio input terminal.
AC socketConnect the supplied power cord.
Filter cover(Intake vent)
Carrying handleFor carrying the projector.
HDMI terminalTerminal for HDMI input.
DVI-D input terminalsTerminals for DVI digital 
RGB and digital component 
signals and audio input 
terminal.
COMPUTER/COMPONENT1 
input terminals
Terminals for computer RGB 
and component signals and 
audio input terminal.
MONITOR OUT terminals
∫COMPUTER/COMPONENT 
output terminal for computer 
RGB and component signals. 
(Shared for COMPUTER/
COMPONENT 1 and 2 input)
∫AUDIO output terminal.
(Shared for all inputs)
VIDEO input terminalsTerminals for connecting 
video equipment and audio 
input terminal.
Kensington Security
Standard connector
TerminalsRefer to “Connecting the Projector to Other Equipment” on pages 24–26. 
						

							Introduction
-15
Remote Control
31
17
28
47
30
31
36
54
17
39
28
41
18
32
37
41
36
37
38
38
18•4718•47
LIGHT buttonFor lighting all buttons on the 
remote control.
STANDBY buttonFor putting the projector into  
standby mode.
ZOOM buttonsFor adjusting the projected image size.
KEYSTONE buttonFor entering the Keystone 
Correction mode.
MAGNIFY (enlarge/reduce) buttonsFor enlarging/reducing part of the image.
COMPUTER 1/2, DVI, HDMI, 
VIDEO, S-VIDEO buttons
For switching to the respective 
input modes.
AUTO SYNC buttonFor automatically adjusting images 
when connected to a computer.
BREAK TIMER  button For setting the break time. 
L-CLICK buttonFor left-clicking while the ADJ./MOUSE 
switch is in the MOUSE position. 
FOCUS buttonsFor adjusting the focus.
Mouse/adjustment button 
('/"/\/|)
• For moving the computer cursor 
while the ADJ./MOUSE switch is 
in the MOUSE position.
• For selecting menu items while 
the ADJ./MOUSE switch is in the 
ADJ. position. 
ENTER buttonFor setting items selected or 
adjusted on the menu.
SHUTTER buttons• OPEN: For opening the shutter.
• CLOSE: For closing the shutter and 
hiding the projected Image.
FREEZE buttonFor freezing images.
RESIZE buttonFor switching the screen size.
PICTURE MODE buttonFor switching the picture mode.
WIRED R/C JACKFor connecting the remote control 
to the projector when the signals 
from the remote control cannot 
reach the remote control sensor.
Volume buttonsFor adjusting the speaker sound level.
MUTE buttonFor temporarily turning off the 
sound.
R-CLICK/UNDO button• For right-clicking while the 
ADJ./MOUSE switch is in the 
MOUSE position.
• For undoing an operation or 
returning to the previous 
display while the ADJ./MOUSE 
switch is in the ADJ. position.
MENU buttonFor displaying adjustment and 
setting screens.
ON buttonFor turning the power on.
ADJ./MOUSE switchFor switching the remote control 
modes.
H&V LENS SHIFT buttonFor shifting the lens horizontally 
and vertically.
Numbers in  refer to the main pages in this operation manual where the topic is explained.
Note
•The LIGHT button on the remote control is made of luminous material that is visible in the dark. Visibility
will diminish over time. Exposure to light will recharge the luminous buttons. 
						

							-16
Using the Remote Control
Inserting the Batteries
1Press the tab and lift open the battery
cover in the direction of the arrow
.
2Insert the batteries.
•Insert the batteries making sure the po-
larities correctly match the 
 and 
marks inside the battery compartment.
3Insert the tabs on the end of the
battery cover into their slots and
press the cover into position.
Incorrect use of the batteries may cause them to leak or explode. Please follow the precautions below.
 Caution
•Danger of explosion if battery is incorrectly replaced.
Replace only with the alkaline or manganese batteries.
•Insert the batteries making sure the polarities correctly match the 
 and  marks inside the battery compartment.
•Batteries of different types have different properties, therefore do not mix batteries of different types.
•Do not mix new and old batteries.
This may shorten the life of new batteries or may cause old batteries to leak.
•Remove the batteries from the remote control once they have run out, as leaving them in can cause them to leak.
Battery fluid from leaked batteries is harmful to skin, therefore ensure you wipe them first and then remove them using a cloth.
•The batteries included with this projector may run down in a short period, depending on how they are kept.
Be sure to replace them as soon as possible with new batteries.
•Remove the batteries from the remote control if you will not be using the remote control for a long time.
•Comply with the rules (ordinance) of each local government when disposing of worn-out batteries.
Usable Range
The remote control can be used to control the
projector within the ranges shown in the il-
lustration.
Note
•The signal from the remote control can be re-
flected off a screen for easy operation. How-
ever, the effective distance of the signal may
differ depending on the screen material.
When using the remote control:
•Ensure that you do not drop it or expose it to
moisture or high temperature.
•The remote control may malfunction under a
fluorescent lamp. In this case, move the pro-
jector away from the fluorescent lamp.
Front View
Rear View
Remote control
signal transmittersRemote control sensor
Remote control
23 (7 m)
Remote control sensor
Remote control
signal transmitters
Remote control
23 (7 m) 
						

							Introduction
-17
Using the Remote Control with a Signal Cable
When the signals from the remote control cannot be reached due to the positioning of the projector, use a
ø3.5 mm minijack cable to connect the remote control to the projector. Now you can control the projector
with the remote control.
Note
•The wireless remote function is not possible when the ø3.5 mm minijack cable is connected to the projec-
tor. Should the wireless remote operation be required, the ø3.5 mm minijack cable should be discon-
nected from the projector.
Switching the Remote Control Mode
The remote control has two functions. One is projector control and the other is wireless computer mouse.
Slide the ADJ./MOUSE switch on the remote control to other side compatible to the desired usage.
Info
•When using the remote control as the wireless computer mouse, connect the optional remote receiver
(AN-MR2) to the computer. (See page 18.)
ADJ.
MOUSEADJ.
MOUSE
Projector control Wireless computer mouse
Rear view
Remote control
To WIRED R/C JACK
To WIRED REMOTE terminal
ø3.5 mm minijack cable (commercially available or 
available as Sharp service part QCNWGA038WJPZ) 
						

							-18
Using the Remote Control as a Wireless Computer Mouse
When connecting the optional remote re-
ceiver (AN-MR2) to the computer, you can
use the remote control as the wireless com-
puter mouse.
1Connect the optional remote re-
ceiver to the USB terminal on the
computer.
2Slide the ADJ./MOUSE
switch on the remote con-
trol to the MOUSE position.
3Use the mouse function.
•Point the remote control at the remote
receiver.
■When moving the cursor
Press '/"/\/|.
■When left-clicking
Press L-CLICK.
■When right-clicking
Press R-CLICK.
■When your computer supports only a
one-click mouse (such as Macintosh
®)
Press L-CLICK or R-CLICK. (L-CLICK
and R-CLICK have common function.)
ADJ.
MOUSE
Note
•This function only works with the Microsoft®
Windows® OS and Mac OS®. However, this func-
tion does not work with the following operation
systems that do not support USB.
•Versions earlier than Windows® 95.
•Versions earlier than Windows® NT4.0.
•Versions earlier than Mac OS® 8.5.
•Confirm that the computer recognizes the USB
connection.
•While the remote control is connected to the
projector with a signal cable, you cannot use
the wireless computer mouse function.
Computer
To USB terminal
Remote receiver
Mouse/adjustment button ('/"/\/|) ADJ./MOUSE switch
R-CLICK button
L-CLICK button
Using the Remote Control