Sharp Xg Nv6xu Projector User Manual

							E-30
Operation
Auto Sync Adjustment
¥ Used to automatically adjust a computer image.
¥ Auto Sync adjustment can be made manually by
pressing AUTO SYNC, or automatically by setting
ÒAuto SyncÓ to ÒONÓ in the projectorÕs GUI menu.
When ÒAuto SyncÓ is set to ÒONÓ:
¥ The sync adjustment is automatically made each time
the projector is turned on while connected to a com-
puter or the input selection is changed.
¥ The Auto Sync adjustment setting previously made is
cleared when the projectorÕs setting is changed.
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
1Press MENU.
2Press §/© to select ÒFine SyncÓ.
3Press ¶/Ä to select ÒAuto SyncÓ.
4Press §/© to select ÒONÓ.
5To exit from the GUI, press MENU.
¥ Automatic adjustments can be made by pressing AUTO
SYNC.
¥ When the optimum image cannot be achieved with Auto
Sync adjustment, use manual adjustments. (See the
previous page.)
During Auto Sync adjustment, the On-screen Display
changes as shown on the left.
¥ Auto Sync adjustment may take some time to complete,
depending on the image of the computer connected to the
projector.
(GUI) On-screen Display
Computer Image Adjustments
2, 3, 4 1, 5
Projector
g
sf
On-screen Display
AUTO SYNC
buttonMOUSEADJ.
Auto Sync Display Function
Normally, an image is not superimposed during Auto
Sync adjustment. You can, however, choose to
superimpose a backgraund image during Auto Sync
adjustment.
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
1Press MENU.
2Press § /©  to select ÒOptionsÓ.
3Press  ¶/Ä  to select ÒAuto Sync DispÓ.
4Press § /© to select Ò
Ó to superimpose a
background image or Ò
Ó to remove the
background image during Auto Sync adjustment.
5To exit from the GUI, press MENU.
MOUSEADJ.(GUI) On-screen Display
Remote control 
						

							E-31
Operation
Saving and Selecting Adjustment Settings
This projector allows you to store up to seven adjustment
settings for use with various computers. Once these
settings are stored, they can be easily selected each
time you connect the computer to the projector.
Saving the adjustment setting
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
1Press MENU.
2Press §/© to select ÒFine SyncÓ.
3Press ¶/Ä to select ÒSave SettingÓ, and then press
©.
4Press ¶/Ä to select the desired memory location of
the setting.
5Press ENTER to save the setting.
6To exit from the GUI, press MENU.
Selecting a saved setting
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
1Press MENU.
2Press §/© to select ÒFine SyncÓ.
3Press ¶/Ä to select ÒSelect SettingÓ, and then press
©.
4Press ¶/Ä to select the desired memory setting.
5Press ENTER to select the setting.
6To exit from the GUI, press MENU.
¥ If the memory position has not been set, the resolution and
frequency will not be displayed.
¥ When selecting the stored adjustment setting with ÒSelect
SettingÓ, the computer system should match the stored
setting.
(GUI) On-screen Display
2
3
4
Computer Image Adjustments
MOUSEADJ.
MOUSEADJ.
5 2, 3, 4 1, 6
Projector Remote control 
						

							E-32
Operation
Computer Image Adjustments
Special Mode Adjustment
Ordinarily, the type of input signal is detected and the
correct resolution mode is automatically selected.
However, for some signals, ÒSpecial ModesÓ on the ÒFine
SyncÓ menu screen may need to be changed to match
the computer display mode.
(Slide the MOUSE/ADJUSTMENT switch on
the remote control to the ADJ. position.)
1Press MENU.
2Press §/© to select ÒFine SyncÓ.
3Press ¶/Ä to select ÒSpecial ModesÓ.
4Press ¶/Ä to select the optimal resolution mode.
5Press ENTER to save the setting.
6To exit from the GUI, press MENU.
¥ Avoid displaying computer patterns which repeat every
other line (horizontal stripes). (Flickering may occur, making
the image hard to see.)
¥ When inputting DTV 480P signals, select Ò480PÓ in step 
4
above.
5 2, 3, 4 1, 6
Projector
(GUI) On-screen Display
Remote control
MOUSEADJ. 
						

							E-33
Useful Features
Useful Features
Freeze Function
This function allows you to instantly freeze a moving
image. This is useful when you want to display a still
image from a computer or video, giving you more time
to explain the image to the audience.
You can also use this function to display a still image
from a computer while you make preparations for the
next computer images to be presented.
1Press FREEZE to freeze the image.
2Press FREEZE again to return to the moving
image. Projector
1, 2
On-screen Display
Remote control 
						

							E-34
Useful Features
Digital Image Magnification
Projector
13 2
This function allows you to magnify a specific portion of
an image. This is useful when you want to display a
detailed portion of the image.
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ.)
1Press ENLARGE. Each time ENLARGE is
pressed, the image will be magnified.
2When the image is magnified, you can pan and
scan around the image by using ¶/Ä/§/©.
¥ Each time ENLARGE is pressed, image magnification
toggles as shown below.
@1@2@3@4@6@8
¥ If the input signal is changed during digital image
magnification, the image will return to 21. The input signal
is changed
(a) when INPUT is pressed,
(b) when the input signal is interrupted, or
(c) when the input resolution and refresh rate changes.
3To return to 2 1, press UNDO.
MOUSEADJ.
sg
On-screen DisplayRemote control 
						

							E-35
Useful Features
Gamma Correction
Projector
12
¥ Gamma is an image quality enhancement function
that offers a richer image by brightening the darker
portions of the image without altering the brightness
of the brighter portions.
¥ Four gamma settings are available to allow for
differences in the images played and in the brightness
of the room.
¥ When you are watching images with frequent, dark
scenes, such as a film or concert, or when you are
watching images in a bright room, this feature makes
the dark scenes easier to see and gives the impres-
sion of greater depth in the image.
Gamma Modes
MOUSEADJ.
STANDARD
GAMMA 1
GAMMA 2
CUSTOMGamma mode Selected Mode
Standard picture without gamma correction.
Brightens darker portions of image.
Gives greater depth to darker portions of image.
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
1Press GAMMA. Each time GAMMA is pressed,
the gamma level toggles as shown on the left.
2To return to the standard image, press UNDO
while ÒGAMMAÓ is displayed on the screen.
Allows you to adjust gamma value using Sharp
Advanced Presentation Software.
On-screen Display
ss s
s
STANDARD
GAMMA 1
GAMMA 2
CUSTOMRemote control 
						

							E-36
Useful Features
ONVOL
This function allows you to modify or customize the picture display mode to enhance the input image. Depending
on the input signal, you can choose NORMAL, WIDE, DOT BY DOT, DOT BY DOT (WIDE), or FIT TO SCREEN
image.
¥ Each time RESIZE is pressed, the picture mode changes as shown below.
Selecting the Picture Display Mode
g
NORMAL WIDE DOT BY DOT DOT BY DOT (WIDE)
For DTV decoder RGB signal in 4:3 aspect ratio.
For COMPUTER/RGB signal without 4:3 aspect ratio.
gg
For DTV decoder RGB signal in 16:9 aspect ratio.
gg
¥ÒFIT TO SCREENÓ is displayed only when SXGA signals that are not in 4:3 aspect ratio are input.
¥DOT BY DOT mode displays images in their native resolution and not expanded to fit the LCD resolution.
¥ To return to NORMAL mode, press UNDO while ÒRESIZEÓ is displayed on the screen.
g
g
gg
MODE
INPUT SIGNAL4:3
480 P16:9
720 PSXGA
  DTV COMPUTER
NORMAL
WIDE
DOT BY DOT
DOT BY DOT (
WIDE)
1024 2 768
1024 2 576
640 2 480
853 2 4801024 2 576
—
1280 2 720
—960 2 768
1024 2 768
1280 2 1024
—
RESIZE
button
Projector
EXAMPLE
Remote control 
						

							E-37
Useful Features
Black Screen Function
This function can be used to superimpose a black
screen over the projected image.
Blacking out the Projected Image
Press BLACK SCREEN. ÒBLACK SCREENÓ is dis-
played on the screen. To return to the original projected
image, press BLACK SCREEN again.
¥ To use the remote control to operate this
function, slide the MOUSE/ADJUSTMENT switch to the
MOUSE position before pressing BLACK SCREEN.
Turning off the On-screen Display
The On-screen Display (ÒBLACK SCREENÓ) that
appears during black screen can be turned off. When
ÒBLK SCRN DispÓ is set to Ò
Ó in the GUI menu, ÒBLACK
SCREENÓ will not be displayed during function.
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
1Press MENU.
2Press § /©  to select ÒOptionsÓ.
3Press  ¶/Ä  to select ÒBLK SCRN DispÓ.
4Press  §/©  to select Ò
Ó to turn on or ÒÓ to
turn off the function.
5To exit from the GUI, press MENU.
2, 3, 4 1, 5
Projector
(GUI) On-screen Display Projected Image
BLACK
SCREEN
button
This function allows you to turn off the on-screen
messages that appear during Òinput selectÓ and the
ÒIrCOMÓ function. Once ÒOSD DisplayÓ is set to Ò
Ó in
the GUI menu, the on-screen messages will not appear
when INPUT and IrCOM are pressed.
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
1Press MENU.
2Press §/© to select ÒOptionsÓ.
3Press ¶/Ä to select ÒOSD DisplayÓ.
4Press §/© to select Ò
Ó to turn on or ÒÓ to turn
off the On-screen Display.
5To exit from the GUI, press MENU.
On-screen Display Override Function
2, 3, 4 1, 5
Projector
(GUI) On-screen Display
MOUSEADJ.
MOUSEADJ.
MOUSEADJ.
sg
Remote control
Remote control 
						

							E-38
Useful Features
This function allows you to reduce the power
consumption when the projector is off.
Economy Modes
¥ The projector is factory preset to Mode 2.
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
1Press MENU.
2Press §/© to select ÒOptionsÓ.
3Press ¶/Ä to select ÒEconomy ModeÓ, and then
press ©.
4Press ¶/Ä to select the desired mode.
5Press ENTER to save the setting.
6To exit from the GUI, press MENU. (GUI) On-screen Display
Selecting the Economy Mode
5 2, 3, 4 1, 6
Projector
Selected mode
Mode 1
Mode 2
Mode 3
Mode 4Automatic Power
Shutoff
ON
ON
OFF
OFFRS232C/Monitor
out
OFF
ON
OFF
ON
MOUSEADJ.
Automatic Power Shutoff Function
When no input signal is detected for more than 15
minutes, the projector will automatically shut off. The
on-screen message on the left will appear five minutes
before the power is automatically turned off.
CAUTION
¥ Select Mode 2 or Mode 4 when using the Sharp Advanced
Presentation Software (supplied).
On-screen Display
Remote control 
						

							E-39
Useful Features
I/P Conversion
This function allows you to select either an interlaced
display or a progressive display of a video signal. The
progressive display projects a smooth video image.
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
1Press MENU.
2Press §/© to select ÒOptionsÓ.
3Press ¶/Ä to select ÒI/P ConversionÓ, and then
press ©.
4Press ¶/Ä to select ÒInterlacedÓ or ÒProgressiveÓ.
5Press ENTER to save the setting.
6To exit from the GUI, press MENU.
5 2, 3, 4 1, 6
Projector
(GUI) On-screen Display
Checking the Lamp Usage Time
This function allows you to check the accumulated lamp
usage time.
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
1Press MENU.
2Press §/© to select ÒOptionsÓ. The lamp usage
time will be displayed.
¥ It is recommended that the lamp be replaced after
approximately 2,000 hours of usage. See pages 48 and 49
for lamp replacement.
2 1
Projector
(GUI) On-screen Display
MOUSEADJ.
MOUSEADJ.
Remote control
Remote control