Sharp Xg Nv6xu Projector User Manual

							E-20
Operation
Reversed Image Setup
Rear projection
¥ Place a translucent screen between the projector and
the audience.
¥ Use the projectorÕs menu system to reverse the
projected image. (See page 42 for use of this
function.)
Projection using a mirror
¥ Place a mirror (normal flat type) in front of the lens.
¥ Use the projectorÕs menu system to reverse the
projected image. (See page 42 for use of this
function.)
¥ The image reflected from the mirror is projected onto
the screen.
2. Settng up the Screen Continued
¥ Optimal image quality is produced with the projector positioned perpendicular to the screen with all feet flat and level.
CAUTION
¥ When using a mirror, be sure to carefully position both the projector and the mirror so the light does not shine into the eyes of
the audience.
Ceiling-mount Setup
¥ It is recommended that you use the optional Sharp
ceiling-mount bracket for this installation.
¥ Before mounting the projector, contact your nearest
Authorized Sharp Industrial LCD Products Dealer or
Service Center to obtain the recommended ceiling-
mount bracket (sold separately). (AN-XGCM60
ceiling-mount bracket, AN-EP101AP extension tube
for AN-XGCM60.)
¥ When the projector is in the inverted position, use the
upper edge of the screen as the base line.
¥ Use the projectorÕs menu system to select the
appropriate projection mode. (See page 42 for use
of this function.) 
						

							E-21
Operation
3. Operating the Wireless Mouse from the Remote Control
MOUSEADJ.
MOUSE/ADJUSTMENT switch
(Remote control)
MOUSEADJ.
Controlling the Projector
Using the Wireless Mouse
138(4 m)
30˚
30˚
120˚
Remote
mouse
receiver Remote control
Using the Remote Control as a Wireless Mouse
Remote Control/Mouse Receiver Positioning
The remote control has the following three functions:
¥ Projector control
¥ Wireless mouse
¥ Laser pointer
¥ The remote control can be used to control the projector within the ranges shown below.
¥ The remote mouse receiver can be used with the remote control to control the mouse functions of a connected
computer within the ranges shown below.
¥ The signal from the remote control can be reflected off a screen for easy operation. However, the effective distance of the
signal may differ due to the screen material.Wireless mouse
Laser pointerProjector control
Remote control
30˚45˚
238 (7 m)
30˚
30˚
45˚
Remote control 
						

							E-22
Operation
2
Be sure the supplied remote mouse receiver is connected to your computer.
Slide the MOUSE/ADJUSTMENT switch to MOUSE.
Effective buttons in MOUSE mode
Use as a Wireless Mouse
3. Operating the Wireless Mouse from the Remote Control Continued
1
MOUSEADJ.
Use as a Laser pointer
Slide the MOUSE/ADJUSTMENT switch to MOUSE.
Press LASER POINTER (
) to activate the laser pointer.
When the button is released, the light automatically goes off.
¥ For safety, the laser pointer automatically goes off after 1 minute of continuous use. To turn it on, release LASER
POINTER () and press again.
MOUSEADJ.
1
¥ The wireless mouse may not operate correctly if your computer serial port is not correctly set up. Refer to the computerÕs
operation manual for details of setting up/installing the mouse driver.
¥ For one-button mouse systems, use either the LEFT-CLICK or RIGHT-CLICK button.
Using the remote control in a dark room
Press BACKLIGHT, and the buttons will light up. Green lights refer to mouse operations, and red
lights to projector adjustments.
Position of MOUSE/ADJUSTMENT switch
ON (RED)
MOUSE 
LASER POINTER (GREEN)
BLACK SCREEN (GREEN)
RIGHT-CLICK (GREEN)
MOUSE (NOT LIT)
LEFT-CLICK (NOT LIT)
ADJ. 
MENU (RED)
LENS (RED)
ENTER (RED)
ADJUSTMENT (NOT LIT)
UNDO (NOT LIT)
Button name
LASER POINTER/MENU
BLACK SCREEN/LENS
RIGHT-CLICK/ENTER
MOUSE/ADJUSTMENT
LEFT-CLICK/UNDO
POWER ON/OFF
VOLUME `/1
MUTEPosition of MOUSE/ADJUSTMENT switch
ON (RED)
MOUSE ADJ. 
Button name
INPUT
IrCOM
FREEZE
AUTO SYNC
ENLARGE
RESIZE
TOOLS
GAMMA
Wired Remote Control
LEFT-CLICK
RIGHT-CLICK
MOUSE
BLACK SCREENLASER
POINTER
3.5 mm stereo minijack cable
(sold separately)
When the remote control cannot be used due to the range
or positioning of the projector (rear projection, etc.), connect
a 3.5 mm stereo minijack cable (sold separately) from the
wired remote control input on the bottom of the remote
control to the WIRED REMOTE control input terminal on the
rear of the projector.
¥ The laser pointer and wireless mouse functions can still be operated
with the wired remoto control. 
						

							E-23
Operation
Using the GUI (Graphical User Interface) Menu Screens
This projector has two sets of menu screens (INPUT/VIDEO) that allow you to adjust the image and various projector
settings. These menu screens can be operated from the projector or the remote control with the following buttons.
(GUI) On-screen Display
1
INPUT (COMPUTER/RGB) mode
1
VIDEO mode
4(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
1Press MENU to display the INPUT or VIDEO mode
menu bar.
2Press §/© to select an adjustment menu on the
menu bar.
3Press ¶/Ä to select a specific adjustment item.
4To display a single adjustment item, press ENTER
after selecting the item. Only the menu bar and
the selected adjustment item will appear.
5Press §/© to adjust the item.
6Press UNDO to return to the previous screen.
7Press MENU to exit from the GUI.
¥ For details on items on the menu screen, see the tree charts
on the next page.
§ 2 © § 2 ©
§ 
2 ©
§ 
5 ©
MOUSEADJ.
¶
3Ķ3Ä
§ 5 ©
§ 
5 ©
46 2, 3, 5 1, 7
Projector Remote control 
						

							E-24
Operation
Items on the INPUT1 or
INPUT2 Mode Menu Bar Using the GUI (Graphical User Interface) Menu Screens
Items on the VIDEO Mode Menu Bar
10242864
11522864
11522870
11522882
Economy ModeMode 1
Mode 2
Mode 3
Tint
Auto Sync Fine Sync
Audio`30 130
Color`30 130
Clock`150 1150
`150 1150
Treble
Options Lamp Timer
Language English
PRJ Mode
StatusCeiling`Front
Ceiling`Rear Deutsch
Español
Nederlands
Français
Italiano
Svenska
Português
Front
Rear Auto Sync Disp
BLK SCRN Disp
OSD Display
[ON/OFF]
[ON/OFF]
[ON/OFF]
[ON/OFF]
Signal Type
Background
Sharp Startup Image
Signal Info
Sharp Mode 4
Custom
Custom I/P ConversionInterlaced
Progressive
Blue
None Computer/RGB
Component
None `30 130
Balance`30 130
Bass`30 130
Phase`60 160
H-Pos
V-Pos
Reset
Reset Save Setting
Select Setting1
2
•
•
7
Resolution8002600
6402480Vert Freq
75 Hz
72 Hz
Special Modes`60 160
Sharp`30 130
Contrast Picture`30 130
Bright`30 130
Red`30 130
Blue
Reset`30 1301
2
•
•
7
Resolution8002600
6402480Vert Freq
75 Hz
72 Hz
Resolution
Hor Freq
Vert Freq6402480
37.5 KHz
72 Hz
Main menuSub menu
Main menuSub menu
Contrast Picture
Audio`30 130
I/P Conversion Options
Video System
Language English
PRJ Mode
StatusCeiling`Front
Ceiling`Rear Deutsch
Español
Nederlands
Français
Italiano
Svenska
Português
Front
Rear Background
Startup ImageInterlaced
Progressive
Auto
PAL 50 /60Hz
SECAM
NTSC4.43
NTSC3.58
Sharp
Custom
Blue
None Economy ModeMode 1
Mode 2
Mode 3
Mode 4
Sharp
Custom
None Lamp Timer
BLK SCRN Disp
OSD Display
[ON/OFF]
[ON/OFF]
Bright`30 130
Color`30 130
Tint`30 130
Sharp`30 130
Red`30 130
Blue`30 130
Balance`30 130
Treble`30 130
Bass`30 130
Reset
Reset
¥ The resolution, vertical frequency and horizontal frequency figures displayed above are for example purposes only.
¥ ÒColorÓ, ÒTintÓ, and ÒSharpÓ appear only when Component input is selected in INPUT mode.
¥ Only the items highlighted in the tree charts above can be adjusted.
¥ To adjust the items under the sub menu, press © after selecting the sub menu. 
						

							E-25
Operation
The IrCOM function can transfer still images from a
computer or digital camera to the projector via infrared
(wireless) communication.
Sharp Advanced Presentation Software
¥ This function requires the supplied Sharp Advanced
Presentation Software (SAPS).
¥ Install the SAPS in the supplied CD-ROM on the
computer.
¥ See the operation manual of the software for
installation and operating instructions.
¥ Position the projector and the IrCOM transmitting
device within the range shown on the left.
¥ To avoid transmission errors or changes in the image, ensure
the following when setting up the projector and transmitting
device.
¥ The IrCOM sensors on both the projector and transmitting
device are protected from direct sunlight or strong
ambient light.
¥ The transmitting device has sufficient battery power.
¥ The projector and transmitting device are positioned
within the designated operating range.
¥ The IrCOM sensors on the projector and transmitting
device are correctly aligned.
¥ The distance between the projector and transmitting device
may have to be less than 49 (10 cm) depending on the
transmitting device.
¥ When using the digital still camera, set it to the image
transmission mode and set the computer to the image
reception mode.
¥ Align the projector and transmitting device at the same
height and angle at a distance of 49 (10 cm) to 38 39 (1 meter)
with an unobstructed line of view.
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
1Press IrCOM to enter the IrCOM mode. Each time
IrCOM is pressed, the On-screen Display
switches between ÒIr-COM1Ó and ÒIr-COM2Ó.
2And then the On-screen Display changes as
shown on the left.
¥ If the On-screen Display does not change as shown on the
left, the projector may not be within the reception range
from the IrCOM transmitting device.
3Press INPUT to exit the IrCOM mode.
Using IrCOM for Wireless Presentations
Projector
3 1, 2
MOUSEADJ.
Digital camera
On-screen Display
1
f ff f
f
d dd d
d
f ff f
f
f ff f
f
2
¥ If the projector is unable to receive images from the IrCOM
transmitting device, the On-screen display on the left will
appear.
PC
4( (10 cm)–3* 3( (1 m)
45˚
30˚
30˚45˚
30˚
30˚
IrCOM1 IrCOM2Remote control 
						

							E-26
Operation
Selecting the On-screen Display Language
4 2, 3 1, 5
Projector
(GUI) On-screen Display
English is the preset language for the On-screen
Display. It can be changed to English, German, Spanish,
Dutch, French, Italian, Swedish, Portuguese, Chinese,
Korean or Japanese.
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
1Press MENU.
2Press §/© to select ÒLanguageÓ.
3Press  ¶/Ä to select the desired language .
4Press ENTER to save the setting. The On-screen
Display is now programed to display in the
language selected.
5To exit from the GUI, press MENU.
Selecting the Video Input System Mode (VIDEO mode only)
5 2, 3, 4 1, 6
Projector
The video input system mode is preset to ÒAutoÓ;
however, it can be changed to a specific system mode,
if the selected system mode is not compatible with the
connected audiovisual equipment.
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
1Press MENU.
2Press §/© to select ÒOptionsÓ.
3Press ¶/Ä to select ÒVideo SystemÓ, and then
press ©.
4Press ¶/Ä to select the desired video system
mode.
5Press ENTER to save the setting.
6To exit from the GUI, press MENU.
¥ When the system mode is set to ÒAutoÓ, you may not receive
a clear picture due to signal differences. Should this occur,
switch to the video system you are viewing.
(GUI) On-screen Display
MOUSEADJ.
MOUSEADJ.
Remote control
Remote control 
						

							E-27
Operation
2, 3 1, 4
Picture Adjustments
You can adjust the projectorÕs picture to your prefer-
ences with the following picture settings.
Description of Adjustment Items
Projector
For less contrast
For less brightness
For less color intensity
Skin tones become purplish
For less sharpness
For weaker red
For weaker blue Selected itemFor more contrast
For more brightness
For more color intensity
Skin tones become greenish
For more sharpness
For stronger red
For stronger blue
§ button
© button
All image adjustment items are returned to the factory preset
settings. Contrast
Bright
Color
Tint
Sharp
Red
Blue
Reset
(GUI) On-screen Display
(COMPUTER/RGB input in INPUT mode)
1
2
¥ ÒColorÓ, ÒTintÓ and ÒSharpÓ do not appear for COMPUTER/
RGB input in INPUT mode.
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
1Press MENU. Menu bar and ÒPictureÓ menu
screen appear. GUI operation guide is also
displayed.
2Press ¶/Ä  to select a specific adjustment item.
3Press §/© to move the 
 mark of the selected
adjustment item to the desired setting.
4To exit from the GUI, press MENU.
¥ To reset all adjustment items, select ÒResetÓ on the ÒPictureÓ
menu screen and press ENTER.
¥ The adjustments can be stored separately in the ÒINPUT
1Ó, ÒINPUT 2Ó and ÒVIDEOÓ modes.
¥ For COMPONENT input in INPUT mode, ÒSharpÓ is
adjustable only when a DVD player is connected.
MOUSEADJ.
Remote control 
						

							E-28
Operation
This projectorÕs audio is factory preset to standard
settings. However, you can adjust it to suit your own
preferences by adjusting the following audio settings.
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
1Press MENU. Menu bar and ÒPictureÓ menu
screen appear. GUI operation guide is also
displayed.
2Press §/© to select ÒAudioÓ.
3Press ¶/Ä to select a specific adjustment item.
4Press §/© to move the 
mark of the selected
adjustment item to the desired setting.
5To exit from the GUI, press MENU.
¥ To reset all adjustment items, select ÒResetÓ on the ÒAudioÓ
menu screen and press ENTER.
Description of Adjustment Items
2, 3, 4 1, 5
Projector
© button § button Selected item
2
3(GUI) On-screen Display
Audio Adjustments
Increased audio from the left
speakerIncreased audio from the right
speaker
For weaker treble
For weaker bass
Treble
Bass
ResetFor stronger treble
For stronger bass
All audio adjustment items are returned to the factory preset
settings. Balance
MOUSEADJ.
Remote control 
						

							E-29
Operation
Computer Image Adjustments
When displaying computer patterns which are very
detailed (tiling, vertical stripes, etc.), interference may
occur between the LCD pixels, causing flickering,
vertical stripes, or contrast irregularities in portions of
the screen. Should this occur, adjust ÒClockÓ, ÒPhaseÓ,
ÒH-PosÓ and ÒV-PosÓ for optimum computer image.
¥ Computer image adjustment can be made easily by
pressing AUTO SYNC (). See the next page for details.
(GUI) On-Screen Display
2, 3, 4 1, 5
Projector
Adjusts vertical noise.
Adjusts horizontal noise (similar to tracking on your VCR).
Centers the on-screen image by moving it to the left or right.
Centers the on-screen image by moving it up or down.Clock
Phase
H-Pos
V-Pos
Description of Adjustment Items
(Select the desired computer input mode with INPUT.)
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
1Press MENU. Menu bar and ÒPictureÓ menu
screen appear. GUI operation guide is also
displayed.
2Press §/©  to select ÒFine SyncÓ.
3Press  ¶/Ä  to select a specific adjustment item.
4Press §/© to move the 
 mark of the selected
adjustment item to the desired setting.
5To exit from the GUI, press MENU.
¥ To reset all adjustment items, select ÒResetÓ on the ÒFine
SyncÓ menu screen and press ENTER.
2
3
Description Selected item
MOUSEADJ.
Remote control