Sharp Xg Nv3xu Projector User Manual

							E-11
Using the Image Invert/Reverse Function
This projector is equipped with an image invert/reverse function. The projected image can be inverted or reversed
by using the MENU button and the ADJUSTMENT Ä/¶ and §/© buttons.
1
BLK SCRN DISP IMAGE  ADJ.
REVERSE
INVERT INPUT  DISPLAY[OFF]
[OFF]
[OFF] [
OFF]
:SEL.
:ADJ.:ENDMENU
BLK SCRN DISP IMAGE  ADJ.
REVERSE
INVERT INPUT  DISPLAY[OFF]
[ON]
[OFF] [
OFF]
:SEL.
:ADJ.:ENDMENU
22. Reversed Image Mode
In the IMAGE ADJ. menu, press the ADJUSTMENT
Ä/¶ buttons to select ÒREVERSEÓ. Then press the
ADJUSTMENT §/© buttons to select ÒONÓ. The
reversed image will appear.
BLK SCRN DISP IMAGE  ADJ.
REVERSE
INVERT INPUT  DISPLAY[OFF]
[OFF]
[ON] [
OFF]
:SEL.
:ADJ.:ENDMENU33. Inverted Image Mode
In the IMAGE ADJ. menu, press the ADJUSTMENT
Ä/¶ buttons to select ÒINVERTÓ. Then press the
ADJUSTMENT §/© buttons to select ÒONÓ. The
inverted image will appear.
BLK SCRN DISP IMAGE  ADJ.
REVERSE
INVERT INPUT  DISPLAY[OFF]
[ON]
[ON] [
OFF]
:SEL.
:ADJ.:ENDMENU44. Reversed Inverted Image Mode
In the IMAGE ADJ. menu, set the REVERSE and
INVERT functions to ÒONÓ. The reversed inverted
image will appear.
5. Press the MENU button anytime to exit
IMAGE ADJ. 1. Press the MENU button.
With the MENU screen displayed, press the AD-
JUSTMENT Ä/¶ buttons to select ÒIMAGE ADJÓ.
Then press the ENTER button to display the IMAGE
ADJ. screen.
¥ The last MENU screen selected is indicated for about
30 seconds.
Cautions: When setting up the projector
¥ For minimal servicing and to maintain high image quality, SHARP recommends that this projector be installed
in an area free from humidity, dust and cigarette smoke. When the projector is subjected to these environ-
ments, the lens and filter must be cleaned more often. Periodically the filter should be replaced and the pro-
jector should be cleaned internally. As long as the projector is properly maintained in this manner, use in these
environments will not reduce the overall operation life. Please note that all internal cleaning must be performed
by an Authorized Sharp Industrial LCD Products Dealer or Service Center.
¥ Do not expose to extreme heat or cold.
Operating temperature: 41¡F to 104¡F (`5¡C to `40¡C)
Storage temperature: 14¡F to 140¡F (120¡C to `60¡C)
¥ Do not tilt the projector more than 5¡.
How to set up the projector and screen
¥ Position the screen so that it is not in direct sunlight or room light. Light falling directly onto the screen washes
out colors, making viewing difficult. Close the curtains and dim the lights when using the screen in a bright or
sunny room.
¥ The best picture will be obtained when the projector is at a 90 degree angle to the screen. Position the projector
and screen as shown.On-Screen Display 
						

							E-12
Example of a standard setup
TOP VIEW
If the projector and screen are not
centered properly, the picture will be
distorted, making viewing difficult.
tt
90û
90û
Lens center
Lens center
90û
SIDE VIEW
The projector lens should be centered
in the middle of the screen.If the projector and screen are not
centered properly, the picture will be
distorted, making viewing difficult.Lens center
Using the horizontal reverse function makes the following setups possible.
Example of a reversed image setup
¥ By placing a mirror (normal flat type) in front of the lens and using the horizontal reverse function, the image reflected from
the mirror can be projected onto the screen.
¥ Rear projection with a rear projection screen is also possible when using the horizontal reverse function.
AUDIENCE SIDE
Mirror
90û
The projector lens should be centered
in the middle of the screen.
Rear Projection
90û
SIDE VIEW Example of a ceiling-mount setup
Before mounting the projector, be sure to contact your nearest Authorized Sharp Industrial LCD Products Dealer to
obtain the manufacturer recommended ceiling mount bracket (sold separately). (AN-XGCM40 Ceiling Mount
Bracket, AN-EP101AP Extension Tube for AN-XGCM40).
TOP VIEW
¥ If the relative positions of the projector and the screen are not properly adjusted, the picture will be distorted.
Lens center
90û 
						

							E-13
2 1
Adjuster release
Adjusting the Height of the Picture
Use the adjuster release to adjust the angle of the projector and height of the picture. Minor adjustments can be
made with the adjusters.
1. Press the adjuster release and lift the
projector to the desired angle with both
hands.
¥ The adjuster legs will extend to the surface of the
table.
2. Remove your hand from the adjuster
release.
¥ The adjuster legs will lock in position. Release the
projector once you are sure the adjuster legs
have locked in position.
3. Make any minor adjustments necessary.
¥ Turn the adjusters to further adjust the angle of
the projector.
Adjuster
release
Adjusters
3
Carrying handle
When transporting the projector, carry it by the handle located on the
side of the unit.
Note:
¥ Always put on the lens cap to prevent damage to the lens when transporting
the projector.
Caution:
¥ Do not lift or carry the projector by the lens or the lens cover as this may
damage the lens.
Transporting the Projector
Use the carrying handle when carrying the projector.Returning the projector to its original position
¥ While holding the projector with both hands, press the
adjuster release and slowly lower the projector to its original
position.
Notes:
¥ Adjustable up to approximately 5¡ from the horizontal.
¥ When adjustments are made with the adjusters, the picture may
become distorted, depending on the relative positions of the
projector and the screen.
¥ After adjusting, in some cases, all of the adjuster legs may not be
resting on the table.
To prevent the projector from wobbling, adjust the adjuster legs so
that they firmly contact the table.
Cautions:
¥ Do not press the adjuster release when the adjuster legs are
extended without firmly holding the projector.
¥ When lowering the projector, be careful not to get your fingers caught
in the area between the adjusters and the projector.
¥ Do not hold the lens when lifting or lowering the projector. 
						

							E-14
Ô
Connecting the Projector (VIDEO 1, VIDEO 2)
To playback audio and video with the projector connected to a VCR, Laser Disc Player or external audio amplifier,
make the following connections.
¥ Always turn off the LCD Projector while connecting to video equipment, in order to protect both the projector and the
equipment being connected.
Amplifier
COMPUTER AUDIO
PC CONTROL COMPUTER RGB
VIDEO
S-VIDEO12
LOFF ON
R LR
AUDIOIN
2 IN
1AUDIO
OUTPUT
IN 1
OUTIN 2
WIRED
REMOTE IN 1 IN 2
110-120V/
200-240V~
To
audio
output
terminalsTo
S-video
output
terminal
Ô
To
audio
output
terminalsTo
audio
input
terminals
Video equipmentVCR
Rear terminals
To
video
output
terminal
Used when the AV equipment
to be connected has an
S-VIDEO output terminal.
Playback Playback
Select the audio you want to output by selecting VIDEO 1 or VIDEO 2.
Note the following when using the S-VIDEO INPUT terminal:
¥ The S-VIDEO INPUT terminal uses a video signal system in which the picture is separated into a color and a luminance signal
to realize a higher-quality picture.
¥ By using the external amplifier, the volume can be amplified for greater sound. 
						

							E-15
Connecting the Projector (RGB 1, 2: Computer)
COMPUTER AUDIO
PC CONTROL COMPUTER RGB
VIDEO
S-VIDEO12
LOFF ON
R LRAUDIOIN
2 IN
1AUDIO
OUTPUT
IN 1
OUTIN 2
WIRED
REMOTE IN 1 IN 2
110-120V/
200-240V~
15-pin D-Sub
RGB Signal Cable (Supplied)
Audio Cable for Personal Computer (Supplied)
Rear terminals
¥ Please carefully read the manual of the computer you will be con-
necting.
¥ Before connecting, be sure to turn both the projector and the computer
off. After making all connections, turn the projector on first. The com-
puter should always be turned on last.
Personal computer6-pin DIN
Mouse Control
Cable for IBM
PS/2 (Supplied)
4-pin DIN
Mouse Control
Cable for
Macintosh
Series
(Supplied)
Macintosh Adaptor
(Supplied)To RS-232C
terminal
RS-232C
cable (Cross
Type, sold
separately) 15-pin D-Sub
Computer Control Cable
(with mouse/RS-232C
input terminal) (Supplied)Note:
¥ By using RGB INPUT 2 and PC CONTROL 2,
another computer can be connected to and
operated with the projector.  The RS-232C func-
tion, however, will not operate when used with
the PC CONTROL 2 terminal. Note:
¥ The arrows (¬, «) indicate the
direction of the signals.
RS-232C (D-sub 9-pin)
Use when controlling the projector from your personal computer.
(RS-232C does not function when connected to PC CONTROL 2.)
MOUSE TERMINAL
Use when operating your personal computer with the wireless mouse
remote control.
Left Terminal: D-sub 9-pin (for IBM/Mac)
Right Terminal: 9-pin mini DIN (for NEC in JAPAN)
Mouse Control Cable (Supplied)
9-pin D-Sub
9-pin D-Sub To display input terminal
COMPUTER CONTROL CABLE
¥ You can connect your projector to a computer for easy projection of full color computer images and an external monitor for
simultaneous viewing. See pages 16 and 17 for details of the connections.
¥ Refer to page 18 for a list of personal computers connectable to the projector. Use with computers other than those listed
may cause some of the functions not to work.
¥ When the RS-232C terminal on this unit is connected to a personal computer via an RS-232C cable (cross type) and the sup-
plied computer control cable, the personal computer can control the projector and the status of the projector can be
checked. See pages 34 and 35 for details.
¥ By connecting the supplied computer control cable to the PC CONTROL terminal on your projector and the supplied mouse
control cables to the mouse terminal on your personal computer, you can use the wireless mouse on the remote control,
instead of the mouse equipped with your personal computer, to operate your personal computer. Refer to page 8 for details.
Notes:
¥ The RS-232C function will only operate when the connection cable is connected to the PC CONTROL 1 terminal on the projector.
¥ The wireless mouse or RS-232C function may not operate if your computer port is not correctly set-up. Please refer to your computer owners
manual for details on setting-up/installing the correct mouse driver.
¥ Do not connect or remove the computer control cable, mouse control cables, or RS-232C cable to/from your computer while it is on. This may
damage your computer.
¥ Do not connect to the mouse input terminals on the computer control cable for IBM/Mac and PC98 simultaneously.
¥ Be sure to use the supplied computer control cable when connecting the PC CONTROL terminals.
ÒPlug and PlayÓ Function
This projector is compatible with VESA-standard DDC 1/DDC 2B.
This projector and a VESA DDC compatible computer will communicate their setting requirements, allowing for quick and easy
set-up.
Note:
¥ The DDC, ÒPlug and PlayÓ function of this projector is only functional when used in conjunction with a VESA DDC compatible computer. 
						

							E-16
Connecting to the Computer RGB Input (RGB 1, 2)/Output Terminals
You can connect your projector to a computer for easy projection of full-color computer images, and an external
monitor for simultaneous viewing.
2 !
1. Connecting to an IBM-PC (VGA, SVGA,
XGA, SXGA) Series computerÑ1,280 @
1,024 maximum resolution
Plug one end of the RGB signal cable into the RGB
INPUT terminal on the projector and the other end
into the RGB signal output terminal on the
computer, and secure the plugs by tightening the
thumb screws.
Notes:
¥ This connection is possible only when using a computer with a VGA/
SVGA/XGA/SXGA or Mac display output port.
¥ By using RGB INPUT 2 and PC CONTROL 2, another computer can
be connected to and operated with the projector.
COMPUTER RGBIN 1 IN 2
ANALOG RGB OUT
1
IBM-PC (VGA,
SVGA, XGA, SXGA)
Series (computer)
RGB Signal
Output Socket Rear view of the projector
RGB Signal
Input Socket
RGB Signal
Cable
(Supplied)
2. Connecting to a Macintosh Series
Computer
640 @ 480, 832 @ 624 or 1,024 @ 768 resolution
!Set the proper switches on the supplied
adaptor.
¥ For 640 2 480 resolution, set switches 1 and
2 to ÒONÓ and 3, 4, 5 and 6 to ÒOFFÓ.
¥ For 832 2 624 resolution, set switches 2 and
4 to ÒONÓ and 1, 3, 5 and 6 to ÒOFFÓ.
¥ For 1,024 2 768 resolution, set switches 2
and 3 to ÒONÓ and 1, 4, 5 and 6 to ÒOFFÓ.
@Connect the supplied Macintosh adaptor to the
RGB signal output terminal on your Macintosh
Series computer, as shown on the left, and
secure the plugs by tightening the thumb
screws.
#Firmly plug one end of the supplied RGB signal
cable into the RGB input terminal on the
projector and the other end to the Macintosh
adaptor on the computer, and secure the plugs
by tightening the thumb screws.
Notes:
¥ Be sure to use the supplied Macintosh adaptor.
¥ Be sure the switches on the adaptor are properly set.
¥ Once the adaptor is connected to a computer and the computer is
turned on, the display mode cannot be changed even if the switches
on the adaptor are reset.
¥ The supplied adaptor is only for use with H-SYNC and V-SYNC out-
put. When connecting a Macintosh Series computer that only outputs
C-SYNC, use a special C-SYNC output adaptor (sold separately).
Macintosh Adaptor (Supplied)
ANALOG RGB OUT
@Macintosh Adaptor (Supplied)
RGB Signal
Output Socket
ON
­
¯
OFF
Macintosh
#
RGB Signal
Cable
(Supplied) ANALOG RGB OUTMacintosh
COMPUTER RGBIN 1 IN 2
RGB Signal
Output Socket RGB Signal
Input SocketRear view of the projector 
						

							E-17
5. Connecting an external monitor
Connect your computer monitor to the projectorÕs COM-
PUTER RGB OUTPUT terminal to view images simulta-
neously on the external monitor and the projection
screen. Select either RGB 1 or RGB 2 to output the
images to the monitor.
53. Connecting to other compatible
computers
When connecting the projector to a compatible computer
other than an IBM-PC (VGA/SVGA/XGA/SXGA) or
Macintosh series, a separate cable may be needed.
Please contact your dealer for ordering information.
Notes:
¥ Connecting computers other than the recommended types may
result in damage to the projector, the computer, or both.
¥ Connect the audio from the computer to the COMPUTER AUDIO
INPUT terminal.
4. Connecting to the COMPUTER AUDIO
INPUT
¥ The COMPUTER AUDIO INPUT 1 accepts audio from
the COMPUTER RGB 1 input, and the COMPUTER
AUDIO INPUT 2 accepts audio from the COMPUTER
RGB 2 input.
¥ Connect a 3.5 mm Stereo Minijack cable from the
audio output terminal on the computer to the
COMPUTER AUDIO INPUT terminal on the projector.
4COMPUTER AUDIO
PC CONTROL12
AUDIO
OUTPUT
IN 2
WIRED
REMOTE IN 1 IN 2
Caution (Apple Macintosh):
Do not connect the COMPUTER RGB OUTPUT to any moni-
tor except the following:
Apple Color RGB Monitor 13(/14( (640 2 480), 16(/17( (832
2 624) or 19( (1,024 2 768)
The output signal from the projector to the monitor should be
the same as the input signal from the computer to the
projector.
Examples:
Input 13(/14( (640 2 480) ® Output (640 2 480)
Input 16(/17( (832 2 624) ® Output (832 2 624)
Input 19( (1,024 2 768) ® Output (1,024 2 768)
Note:
¥ The supplied adaptor is only for use with H-SYNC and V-SYNC
output. No picture will appear when connected to monitors that
only use C-SYNC.
COMPUTER RGBIN 1
OUTIN 2
Optional Macintosh
adaptor cable
External Macintosh
monitor orU.S.A. ONLY
External IBM-PC
monitor Direct
connection
Notes:
¥ When using the projector with an external IBM-PC monitor, connect
the monitor using the supplied cable. When using the projector with a
Macintosh monitor, an optional adaptor cable is required. Before
using any other type of monitor, carefully check the monitorÕs inter-
face specifications and make sure that they match the specifications
of the projectorÕs interface.
¥ The external monitor output will only display an analog computer
input signal. It will not display a digital or video input signal. To split
the composite video signal, use a video distribution amplifier. This is
available from your local dealer. The computer RGB output will only
loop through the same signal connected to the computer RGB input.
(VGA IN ® VGA OUT, Mac IN ® Mac OUT) 
						

							E-18
Input Signals (Recommended Timing)
For IBM and compatiblesFor Apple Macintosh Series
Input signals:
The video output signal timing of different types of
video signals are shown below for reference.
e
a
b
c
d
w
x
yz
VIDEO SIGNAL
C-SYNC(H)
C-SYNC(V) VIDEO SIGNAL
V-SYNC
e = 2 dot
abc d
w
x
yz
VIDEO SIGNAL
HORIZONTAL
SYNC SIGNAL
VIDEO SIGNAL
VERTICAL 
SYNC SIGNAL
E D O MM B IMB IMB IMB IMB IMB IMB IMB IMB Iel p p Ael p p Ael p p A
A G VAS E VAG V SAG V SAG V SAG V SAG XAG XAG Xh s o t n i c a M
M TI Ii sh s o t n i c a MM TC Lh s o t n i c a MM T
c i h p a r G Text
720 dots 640 dots 640 dots640 dots
640 dots 832 dots 800 dots 800 dots 800 dots 800 dots 1,024 dots 1,024 dots 1,024 dots
350 lines 400 lines 350 lines 400 lines 480 lines 480 lines480 lines
480 lines 624 lines 600 lines 600 lines 600 lines 600 lines 768 lines 768 lines 768 lines c i h p a r Gci h p a r GA S E V
e n i l e d i u GA S E V
d r a d n a t SA S E V
d r a d n a t SA S E V
e n i l e d i u GA S E V
d r a d n a t SA S E V
d r a d n a t Sr o t i n o M  3 1ro t i n o M  3 1ro t i n o M  6 1e l p p A
h s o t n i c a M
M T
r o t i n o M  9 1
O E D I VL E V E Lp - p V 7 . 0
5 7Wd a o lp - p V 7 . 0
5 7Wd a o lp - p V 7 . 0
5 7Wd a o lp - p V 7 . 0
5 7Wd a o lp - p V 7 . 0
5 7Wd a o lp - p V 7 . 0
5 7Wd a o lp - p V 7 . 0
5 7Wd a o lp - p V 7 . 0
5 7Wd a o lp - p V 7 . 0
5 7Wd a o l. x a m p - p V 1
5 7Wd a o l
. x a m p - p V 7 . 0
5 7Wd a o l. x a m p - p V 7 . 0
5 7Wd a o l
E P Y T R•G•B R•G•B R•G•B R•G•B R•G•B R•G•B R•G•B R•G•B R•G•BR•G•B
C N Y S . CR•G•B
C N Y S . CR•G•B
C N Y S . C
H
S
Y
N
CH C R O P T N O R Fato d71414242046561424261468713
C N Y Sbto d80 169042782 102 10863 163 169462656
H C R O P K C A Bcto d550582 182 1884606 106 144 167 16961 142 2
D O I R E P O E D I Vdto d02 704 604 600 800 800 800 842 0 , 142 0 , 142 0 , 104 604 623 8
) d + c + b + a ( H 1t o d00 900 823 842 0 , 165 0 , 104 0 , 165 0 , 144 3 , 182 3 , 121 3 , 146 869 825 1 , 1
ms47 7 7 . 1 367 7 7 . 1 331 4 . 6 244 4 . 8 200 4 . 6 200 8 . 0 233 3 . 1 277 6 . 0 270 7 . 7 106 6 . 6 141 7 5 . 8 259 5 . 8 242 1 . 0 2
t o d 1sn28 0 3 . 5 391 2 7 . 9 364 7 . 1 377 7 . 7 200 0 . 5 200 0 . 0 220 2 . 0 2 15.385 3. 3 17. 2 188 6 0 . 3 336 0 4 1 9 . 1 386 4 . 7 1
1H/zH k98 6 4 . 1 388 6 4 . 1 306 8 . 7 365 1 . 5 397 8 . 7 377 0 . 8 457 8 . 6 4 48.363 67 4 . 6 532 0 . 0 600 0 0 . 5 394 1 1 7 9 . 4 339 6 . 9 4
t o d / 1zH M22 3 . 8 257 1 . 5 200 5 . 1 300 0 . 6 300 0 . 0 400 0 . 0 500 5 . 9 400 0 . 5 60. 5 757 . 8 700 4 2 . 0 394 1 4 3 3 . 1 364 2 . 7 5
L E V E LTTL TTL TTL TLTTLTTLTTLTTLTTLTTLTTLTTLTTLTTLT
Y T I R A L O P C N Y S–/ ++– +– – – –/ + +++–– + – – –
V
S
Y
N
CH C R O P T N O R FwH8331833111911 73 1331 3 3 1
C N Y S xH2222232463663 3 3 3
H C R O P K C A ByH95439543238222323212929282939393
D O I R E P O E D I VzH05 300 405 300 408 408 400 600 600 600 686 786 786 708 408 442 6
) z + y + x + w ( V 1H94 494 494 494 452 502 552 682 666 652 660 860 800 852 552 576 6
s m18 6 2 . 4 118 6 2 . 4 118 6 2 . 4 118 6 2 . 4 123 8 6 . 6 153 7 . 3 187 7 . 7 197 5 . 6 135 8 . 3 133 3 . 3 166 6 . 6 127 2 . 4 182 3 . 3 100 . 5 100 . 5 132 4 . 3 1
1v/zH66 8 0 . 0 766 8 0 . 0 736 8 0 . 0 736 8 0 . 0 750 4 9 . 9 590 8 . 2 705 2 . 6 571 3 . 0 688 1 . 2 700 0 . 5 760 0 . 0 696 0 . 0 792 0 . 5 776 . 6 676 . 6 620 5 . 4 7
L E V E LTLTTLTTLTTLTTLTTLTTLTTLTTLTTLTTLTTLTTLTTLTTLTTLT
Y T I R A L O P C N Y S–/ +– +– +– – –/ + +++–– +M B I
SXGA SXGA
1,280 dots
1,024 linesA S E V
d r a d n a t S
p - p V 7 . 0
5 7Wd a o l
R•G•B
48
112
248
1,280 1,280
1,688
15.6
9.3
63.981
108.000
TLT
+
1
3
38
1,024
1,066
16.7
60.020
TLT
+M B I
1,280 dots
1,024 linesA S E V
d r a d n a t S
p - p V 7 . 0
5 7Wd a o l
R•G•B
6 1
144
248
1,688
12.5
7.4
79.976
135.000
TLT
+
1
3
38
1,024
1,066
16.7
75.025
TLT
+–––1,024 dots
768 lines
. x a m p - p V 7 . 0
5 7Wd a o l
R•G•B
C N Y S . C
35
96
173
1,024
1,328
16.650
12.538
60.0
79.76
TLT
–
3
3
30
768
804
13.387
74.70
TLT
–
Notes:
¥ When connecting a notebook computer to the data-projector for display on an (800 2 600) LCD screen, the screen may
not show a full picture image. See page 20, ÒComputer Mode Memory AdjustmentsÓ for details.
¥ This projector may not be able to display images from notebook computers in simultaneous (CRT/LCD) mode. If this
occurs, turn off the LCD display on the notebook computer and output the display data in ÒCRT onlyÓ mode. Details on
how to change display modes can be found in your notebook computerÕs operation manual. 
						

							E-19
RGB Adjustment Controls
When displaying computer patterns which repeat every other dot (tiling, vertical stripes, etc.), interference may
occur between the LCD pixels, causing flickering, vertical stripes, or contrast irregularities in portions of the
screen. Should this occur, use the ADJUSTMENT §/© buttons for HORIZONTAL (LEFT/RIGHT) and VERTICAL
(UP/DOWN) position adjustments to adjust for the optimum picture.
RGB Input Adjustments (CLOCK, PHASE, V-POS and
H-POS)
1. Select the input of the image you want to adjust (RGB 1 or
2) with the INPUT SELECT button and press the MENU
button.
With the MENU screen displayed, press the ADJUSTMENT Ä/¶ buttons
to select ÒRGB 1 INPUT ADJ.Ó Then press the ENTER button to display the
RGB 1 INPUT ADJ. screen.
2. Select the item you wish to adjust with the  ADJUST-
MENTÄ/¶ buttons. Adjust the item with the ADJUST-
MENT§/© buttons.
Note:
¥ To display only the item that you want to adjust, press the ENTER button after selecting the item
with the ADJUSTMENT Ä/¶ buttons. Then adjust the item with the ADJUSTMENT §/© buttons.
3. Press the MENU button anytime to exit RGB INPUT ADJ.
Description of Adjustment Items
CLOCK SPEED ADJUSTMENT (FAST/SLOW)
¥ Adjust the input signal horizontal frequency and the dot clock so that the screen
display is normal.
PHASE ADJUSTMENT (UP/DOWN)
¥ Used to reduce image distortion or improve contrast.
HORIZONTAL POSITION ADJUSTMENT (LEFT/RIGHT)
¥ Used to center the on-screen image by moving it to the left or right.
VERTICAL POSITION ADJUSTMENT (UP/DOWN)
¥ Used to center the on-screen image by moving it up or down.
MODE ADJUSTMENT
C
ONNECTING TO IBM-PC COMPUTERS¥ Ordinarily, the type of input signal is detected and the correct resolution mode
(Text or Graphics) is automatically selected. However, for the following signals,
set MODE to ON or OFF to select the projectorÕs resolution mode to match the
computer display mode properly.
720 dots 2 400 lines, 720 dots 2 350 lines (Text Mode)
640 dots 2 400 lines, 640 dots 2 350 lines (Graphic Mode)
¥ For graphic mode, select MODE and set the MODE to ON.
¥ For text mode, select MODE again at this time, and set MODE to OFF.
C
ONNECTING TO MACINTOSH LC/II SERIES COMPUTERS¥ When connecting to a Macintosh II with 35 kHz Dot Frequency, select MODE
and set MODE to ON.
¥ When connecting to a Macintosh LC Series computer with 34.97 kHz Dot Fre-
quency, set MODE to OFF.
¥ When connecting to third party video cards and other Macintosh computers, set
MODE to ON or OFF to select the correct display mode.
¥ When the input signal is automatically detected or when there is no input signal,
MODE (---) appears on the screen and the display mode cannot be changed.
INITIAL RESET
¥ To return the H-POS, V-POS, PHASE and CLOCK adjustments to their initial
settings, select RESET and then press the ENTER button.
MEMORY SELECT
¥ Used to store up to seven computer mode adjustments.
Note:
¥ Avoid displaying computer patterns which repeat every other line (horizontal stripes). (Flickering
may occur, making the picture hard to see.)
2RGB1  INPUT  ADJ.
PHASEH-POSV-POSMODERESET
MEMORY SELECT  +
0 0
0
0
:SEL.
:ADJ.:NEXTENTER:ENDMENU
[OFF]
- + - + - + -
CLOCK
On-Screen Display 
						

							E-20
Computer Mode Memory Adjustments
¥ The projector has been preset with different modes for
use with XGA and other compatible computers.
However, 7 memory positions are provided to store
mode adjustments.
¥ Each memory position can be used to store mode
adjustments to match the computer.
1. Press the ENTER button to select the
Memory Adjustment mode.
¥ Press the MENU button. While the MENU screen
is displayed, press the ADJUSTMENT Ä/¶ but-
tons to select ÒRGB1 INPUT ADJ.Ó Press the
ENTER button. The MENU mode changes as
shown.
¥ While the RGB INPUT adjustment menu is dis-
played, press the ADJUSTMENT Ä/¶ buttons to
select ÒMEMORY SELECTÓ. Then press the
ENTER button to change the image.
2. Press the ADJUSTMENT §/© buttons.
¥ The screen shown on the left will appear. There
are 7 memory positions.
¥ Press the ADJUSTMENT Ä button once to move
to the following screen. Press the ADJUSTMENT
§/© buttons to select the number of the memory
you want to adjust. If that memory position has
not been set, the screen on the right will be dis-
played. If it has been set, the screen on the left
will be displayed. MEMORY No.0 cannot be set. It
contains the fixed factory preset settings.
¥ To make or change a setting, press the ADJUST-
MENT Ä/¶ buttons to move the cursor to ÒSET-
TING.Ó Then press the ENTER button to go to the
RGB INPUT adjustment menu screen. (If you do
not want to make any adjustments, press the
MENU button.)
¥ Select the item you want to adjust by pressing the
ADJUSTMENT Ä/¶ buttons, then use the AD-
JUSTMENT §/© buttons to make the adjust-
ments. When adjustments are completed, press
the MENU button. The display disappears and
the adjustments are stored in memory as a user
mode. See page 19 for details on the adjustment
items.
3. Press the MENU button anytime to exit
RGB INPUT ADJ. 1
  When RGB 1 or 2 is selected.
2
RGB1  ADJ.
RGB1  INPUT  ADJ.
IMAGE  ADJ.
AUDIO
SYSTEM  SETUP
LANGUAGE
:SEL.:NEXTENTER:ENDMENU
RGB1  INPUT ADJ.
PHASEH-POSV-POSMODERESET
MEMORY SELECT  +
0 0
0
0
:SEL.:NEXTENTER:ENDMENU
[OFF]
- + - + - + -
CLOCK
MEMORY  SELECT
:SEL.
:ADJ.ENTER:ENDMENU
 0 1 2 3 4 5 6 7
STANDARD SETTING
SETTING
:ENTER
MEMORY  SELECT
SETTING
:SEL.:BACKENTER:ENDMENU
 0 1 2 3 4 5 6 7
MEMORY  SELECT
NON
SETTING
:SEL.
:ADJ.ENTER:ENDMENU
 0 1 2 3 4 5 6 7
:ENTER
MEMORY  SELECT
:SEL.
:ADJ.ENTER:ENDMENU
 0 1 2 3 4 5 6 7
RESOLUTION
HOR  FREQ
VERT  FREQ
SETTING
:ENTER
HzKHz  60.0
 75  1024´768
On-Screen Display