Sharp Xg Mb70x Projector User Manual

MULTIMEDIA PROJECTOR
MODEL
XG-MB70X
OPERATION MANUAL
Introduction
Quick Start
Setup
Connections
Basic Operation
Useful Features
Appendix
XG-MB70X_E_Hyo1.p652004.8.6, 11:56 AM 1 

IMPORTANT
For your assistance in reporting the loss or theft of your
Projector, please record the Serial Number located on
the bottom of the projector and retain this information.
Before recycling the packaging, please ensure that you
have checked the contents of the carton thoroughly
against the list of “Supplied accessories” on page 10.Model No.: XG-MB70X
Serial No.:
XG-MB70X_E_Pii_iv.p652004.8.6, 11:55 AM 1 

SPECIAL NOTE FOR USERS IN THE U.K.
The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 5A fuse. Should
the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked 
 or  and of the same rating as
above, which is also indicated on the pin face of the plug, must be used.
Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse cover fitted.
In the unlikely event of the socket outlet in your home not being compatible with...

The supplied CD-ROM contains operation instructions in English, German, French, Swedish, Spanish, Italian,
Dutch, Portuguese, Chinese (Traditional Chinese and Simplified Chinese), Korean and Japanese. Carefully read
through the operation instructions before operating the projector.
Die mitgelieferte CD-ROM enthält Bedienungsanleitungen in Englisch, Deutsch, Französisch, Schwedisch, Spanisch,
Italienisch, Niederländisch, Portugiesisch, Chinesisch (Traditionelles Chinesisch und einfaches Chinesisch) und...

-1
IntroductionBefore using the projector, please read this operation manual carefully.
There are two important reasons for prompt warranty registration of your new SHARP Projector, using
the REGISTRATION CARD packed with the projector.
1. WARRANTY
This is to assure that you immediately receive the full benefit of the parts, service and labor
warranty applicable to your purchase.
2. CONSUMER PRODUCT SAFETY ACT
To ensure that you will promptly receive any safety notification of inspection, modification,...

-2
WARNING:
The cooling fan in this projector continues to run for about 90 seconds after the projector enters the standby mode.
During normal operation, when putting the projector into standby mode always use the STANDBY button on the
projector or on the remote control. Ensure the cooling fan has stopped before disconnecting the power cord.
DURING NORMAL OPERATION, NEVER TURN THE PROJECTOR OFF BY DISCONNECTING THE POWER CORD.
FAILURE TO OBSERVE THIS WILL RESULT IN PREMATURE LAMP FAILURE.
Caution...

-3
Introduction
-40
The menu can be operated to achieve two functions, adjustments and settings. (For setting
the menu items, see pages 42 and 43. )
Using the Menu Screen
Menu Selections (Adjustments)Example: Adjusting “Bright”•This operation can also be performed by using the buttons on the projector.
Menu icons
ENTER 
buttonMENU button
UNDO button MOUSE / 
Adjustment
button ('/"/\/|)Adjustment 
buttons ('/"/\/|)
MENU buttonENTER button
Example: “Picture” screen menu for
INPUT 1 (RGB)...

-4
Contents
Preparing
Setting up the Projector .............................. 19Setting up the Projector ..................................... 19
Projecting a Reversed Image ............................ 20
Connections
Connections ................................................. 21INPUT/OUTPUT Terminals and Connectable
Main Equipment .......................................... 21
Samples of Cables for Connection ............. 22
Connecting to a Computer .......................... 23
Using the Remote...

-5
Introduction
Reference
Appendix
Maintenance ................................................. 63
Maintenance Indicators ............................... 64
Regarding the Lamp .................................... 66
Lamp ................................................................. 66
Caution Concerning the Lamp .......................... 66
Replacing the Lamp .......................................... 66
Removing and Installing the Lamp Unit ............ 67
Resetting the Lamp Timer...

-6
1. Read InstructionsAll the safety and operating instructions should be read before
the product is operated.
2. Retain InstructionsThe safety and operating instructions should be retained for
future reference.
3. Heed WarningsAll warnings on the product and in the operating instructions
should be adhered to.
4. Follow InstructionsAll operating and use instructions should be followed.
5. CleaningUnplug this product from the wall outlet before cleaning. Do
not use liquid cleaners or aerosol cleaners....