Sharp Xg F315x Projector User Manual

57
Appendix
Regarding the Lamp
Lamp■It is recommended that the lamp (sold separately) be replaced when the remaining lamp life becomes
5% or less, or when you notice a significant deterioration in the pictur\
e and color quality. The lamp life
(percentage) can be checked with the on-screen display. (See page  48.)
■ Purchase a replacement lamp of type AN-F310LP from your place of purchase, nearest Sharp
Authorized Projector Dealer or Service Center.
Caution Concerning the Lamp■This projector utilizes a...

58
Regarding the Lamp (Continued)
Removing and Installing
the Lamp Unit
•Make sure that you remove the lamp unit by
the handle. Do not touch the glass surface of
the lamp unit or the inside of the projector.
•T o avoid injury to yourself and damage to the
lamp, make sure you carefully follow the steps
below.
• Do not loosen other screws except for the
lamp unit cover and lamp unit.
Press  STANDBY/ON  on the projec-
tor or  STANDBY  on the remote
control to put the projector into
standby mode.
•W ait...

59
Appendix
Remove the lamp unit.•Loosen the securing screws from the
lamp unit. Hold the lamp unit by the
handle and pull it in the direction of the
arrow. At this time, keep the lamp unit
horizontal and do not tilt it.
Resetting the Lamp Timer
Reset the lamp timer after replacing the lamp.
Insert the new lamp unit.•P ress the lamp unit firmly into the lamp
unit compartment. Fasten the securing
screws.
Replace the lamp unit cover.• Align the tab on the lamp unit cover
(1 ) and place it while pressing...

60
Storing the Projector
Info
How to Use the Storage Case
When storing the projector, attach the lens cap
to the lens, and place it in the supplied storage
case.
1
2Open the cover of the storage
case.
•Ensure the projector has cooled down
sufficiently before placing it in the case.
• When you place the projector into the
storage case, make sure that the
cooling fan has stopped.
• Ensure the lens cap is attached to the
lens for protection.
• Place the projector into the storage
case with the lens facing...

61
Appendix
Computer
Computer Compatibility Chart
•Multiple signal support
Horizontal Frequency: 15-110 kHz,
Ve rtical Frequency: 45-85 Hz,
The following is a list of modes that conform to VESA. However, this projector supports other
signals that are not VESA standards.
27.0
31.5
37.5
27.0
31.5
37.9
27.0
31.5
27.0
31.5
37.9
26.2
31.5
34.7
37.9
37.5
43.3
31.4
35.1
37.9
46.6
48.1
46.9
53.7
40.3
48.4
56.5
60.0
68.7
45.0
47.7
62.7
47.6
47.8
55.0
66.2
67.5
64.0
80.0
64.0
75.0
34.9
49.7
60.2
68.7 60
70
85
60...

62
Troubleshooting
ProblemCheck
•P rojector power cord is not plugged into the wall outlet.
• Power to the external connected devices is off.
•The selected input mode is wrong.
•Cables are incorrectly connected to the projector.
•Remote control battery has run out.
•External output has not been set when connecting notebook computer.
•The lamp unit cover is not installed correctly.
•
If the connected DVI digital equipment is turned on before the “DVI-D”
input mode is selected on the projector, the image...

63
Appendix
Problem
Maintenance indicator on the projector illuminates
or blinks in red.
The projector cannot
be turned on or put into
the standby mode
using  STANDBY/ON  on
the projector.
Picture is green on COMPUTER
(Component)/
DVI (Component).
Picture is pink(no green) on
COMPUTER (RGB)/
DVI (RGB).
Picture is too bright and
whitish.
The cooling fan becomes
noisy.
The lamp does not light up even after the
projector turns on.
The lamp suddenly turns
off during projection.
The image sometimes flickers....

64
For SHARP Assistance
If you encounter any problems during setup or operation of this projector, first
refer to the “Troubleshooting” section on pages 62 and  63. If this operation manual
does not answer your question, please contact the SHARP Service departments
listed below.
U .S.A. Sharp Electronics Corporation
1-888-GO-SHARP (1-888-467-4277)
[email protected]
http://www.sharpusa.com
Canada Sharp Electronics of Canada Ltd. (905) 568-7140
http://www.sharp.ca
Mexico Sharp Electronics Corporation...

65
Appendix
Specifications
As a part of policy of continuous improvement, SHARP reserves the right to make design andspecification changes for product improvement without prior notice. The performance specifica-tion figures indicated are nominal values of production units. There may be some deviations from
these values in individual units.
Model
Display device
Resolution
Lens
Input terminal
Output terminal
Control, others
Speaker
Projection lamp
Rated voltage
Rated frequency
Input current
Po wer...

66
Dimensions
Units: inches (mm)
12 13/32 (315) 3 
1/16 (
77.5)
3 5/32 ( 80)
1 55/64 (47)
2 
7/8 (
73)
4 19/64 (
109) 11 
1/32 (
280)
23/64 (9)
13/64 (5)
7/16 (11)
ø 9 7/64 (69.2)
2 19/32(65.5)
1 53/64(
46.2)
2 61/64(
75)
1 
11/32 (
33.8)
1 7/8 (47.5)
4 7/64 (104)
7/16 (11)