Sharp Xg E1200u Projector User Manual

E-21
RGB Adjustment Controls
nWhen displaying computer patterns which repeat every other dot (tiling, vertical stripes, etc.),
interference may occur between the LCD pixels, causing flickering, vertical stripes, or contrast
irregularities in portions of the screen. Should this occur, use the ADJUSTMENT 
/ buttons
for HORIZONTAL (LEFT/RIGHT) and VERTICAL (UP/DOWN) position adjustments to adjust
for the optimum picture.
RGB Input Adjustments (CLOCK, PHASE, V-POS and
H-POS)
1. Select RGB 1 or 2 with the...

E-22
ON/OFF
POWER
LAMP
TEMP.
Basic Operation of the Projector
1
When the power is on, the LAMP
REPLACEMENT indicator flashes
to show the operating condition of
the lamp.
Green: Lamp is ready
Flashing green: Warming up
Red: Change bulb
ONA.C.120V
C.A.120V
OFF
1AC cord
1. Connect the AC cord.
Connect the supplied AC cord to the AC inlet on the side
of the projector .
2. Turn on the MAIN POWER.
Press the MAIN POWER switch on the side of the projec-
tor. The POWER indicator lights red and the projector...

E-23
On-Screen Display
LANGUAGE
:SEL.:ENTERENTER:ENDMENU
NEDERLANDS ESPAÑOL
DEUTSCH
ENGLISH
SVENSKA ITALIANO FRANÇAIS
5. Select one of eight ON-SCREEN DISPLAY
languages.
You can return to the previous screen by selecting the
uppermost item (turquoise) with the ADJUSTMENT 
/
buttons (in this case, LANGUAGE) and then pressing
the ENTER button.
The on-screen display is set to English at the factory. The
language for the unitÕs ON-SCREEN DISPLAY can be set
to English, German, Spanish, Dutch, French,...

E-24
8. Press INPUT CHECK.
When the INPUT CHECK button on the remote control is
pressed, the current input mode is displayed for about 4
seconds.
Note:
·The INPUT CHECK button will not function if the INPUT
DISPLAY is turned off, as described on page 31.
9. Adjust the volume.
Press the VOLUME UP-DOWN buttons on the projector
or on the remote control to adjust the volume.
MUTE
·Press the MUTE button to temporarily turn off the
sound.
·Press the MUTE button once again to turn the sound
back on.
10. To turn...

E-25
Adjusting the Picture
3
·This projectorÕs picture is factory preset to standard
settings. However, you can adjust it to suit your own
preferences with the ADJUSTMENT buttons on the
projector and the remote control.
·The adjustments can be memorized in RGB 1, RGB 2
or VIDEO separately.
·Four picture modes can be adjusted: ÒPICTURE,Ó
ÒBRIGHT,Ó ÒRED,Ó  and ÒBLUE.Ó
Adjusting the Picture
1. Use the MENU button to select the mode
to be adjusted.
·When the MENU button is pressed, the MENU mode is
indicated...

E-26
MEMORY  SELECT
:SEL.
:ADJ.ENTER:ENDMENU
 0 1 2 3 4 5 6 7
RESOLUTION
HOR  FREQ
VERT  FREQ
SETTING
:ENTER
Hz KHz  38
 60  800´600
MEMORY  SELECT
NON
SETTING
:SEL.
:ADJ.ENTER:ENDMENU
 0 1 2 3 4 5 6 7
:ENTER
Þ
1When RGB 1 or 2 is selected.
RGB1  ADJ.
RGB  INPUT  ADJ.
IMAGE  ADJ.
AUDIO
SYSTEM  SETUP
LANGUAGE
:SEL.:NEXTENTER:ENDMENU
RGB1  ADJ.
BRIGHT
RED
BLUE
RESET
MEMORY  SELECT +
0 0
0
0
:SEL.:NEXTENTER:ENDMENU
- + - + - + -
PICTURE
Þ
Þ
Þ
MEMORY  SELECT
SETTING
:SEL.:BACKENTER:ENDMENU
 0 1 2 3 4 5 6 7...

E-27
Adjusting the Audio
·The projectorÕs audio is factory preset to the standard
setting. However, you can adjust it to suit your own
preference with the ADJUSTMENT buttons on the
projector or the remote control.
·You can adjust the BALANCE, TREBLE and BASS.
·To return to the factory preset mode, press the AD-
JUSTMENT 
/ buttons to select ÒRESETÓ, then press
the ENTER button.
·Press the MENU button to select the normal screen
mode.
Adjusting the Audio
·Press the MENU button.
Select ÒAUDIOÓ with the...

E-28
E-ZOOM Function
nThis projector has an E-ZOOM (640 ´ 480 dots, etc.)
mode which enlarges the display when inputting an
image of less than 800 ´ 600 dots in resolution. In the
XGA (1,024 ´ 768 dots) mode, compression enables
full-mode display.
1. Press the MENU button to select E-ZOOM
mode.
Press the MENU button. While the MENU screen is
displayed, press the ADJUSTMENT 
/ buttons to select
ÒIMAGE ADJ.Ó Then press the ENTER button to display
the IMAGE ADJ. screen as shown. Press the ADJUST-
MENT 
/...

E-29
Setting Up the System
nUsing this function, you can check the input signal,
select the remote mouse, and select DC 5V output.
Checking the system
·Press the MENU button. Select ÒSYSTEM SETUPÓ with the
ADJUSTMENT / buttons. Then press the ENTER button to
change to the picture indicated on the left.
·The current system conditions will be displayed on the screen.
·Press the MENU button to select the normal screen mode.
Note:
·In the video screen, the resolution and frequency settings will
not be...

E-30
Using the Black Screen Function
nThis projector is equipped with a Black Screen Func-
tion. This function can be used to black out the presen-
tation image.
·Press the MENU button. While the MENU screen is
displayed, press the ADJUSTMENT 
/ buttons to
select ÒIMAGE ADJ.Ó Then press the ENTER button to
display the IMAGE ADJ. screen shown. Press the
ADJUSTMENT 
/ buttons to select ÒBLACK SCREEN,Ó
and press the ADJUSTMENT 
/ buttons to select
ON. Then press the MENU button to display the black
screen....