Sharp Xg E1200u Projector User Manual

							E-21
RGB Adjustment Controls
nWhen displaying computer patterns which repeat every other dot (tiling, vertical stripes, etc.),
interference may occur between the LCD pixels, causing flickering, vertical stripes, or contrast
irregularities in portions of the screen. Should this occur, use the ADJUSTMENT 
/ buttons
for HORIZONTAL (LEFT/RIGHT) and VERTICAL (UP/DOWN) position adjustments to adjust
for the optimum picture.
RGB Input Adjustments (CLOCK, PHASE, V-POS and
H-POS)
1. Select RGB 1 or 2 with the INPUT SELECT button and press
the MENU button to select the RGB INPUT ADJ. mode.
With the MENU screen displayed, press the ADJUSTMENT / buttons to select
ÒRGB INPUT ADJ.Ó Then press the ENTER button to display the RGB INPUT
ADJ. screen.
2. Select the item you wish to adjust with the  ADJUSTMENT
/ buttons. Adjust the item with the  ADJUSTMENT /
buttons.
Note:
¥ To display only the item that you want to adjust, press the ENTER button after selecting the item
with the ADJUSTMENT 
/ buttons. Then adjust the item with the ADJUSTMENT / buttons.
3. Press the MENU button anytime to exit RGB INPUT ADJ. 2
RGB  INPUT  ADJ.
PHASEH-POSV-POSMODERESET
 +
0 0
0
0
:SEL.
:ADJ.:NEXTENTER:ENDMENU
[OFF]
- + - + - + -
CLOCK
Description of Adjustment Items
CLOCK SPEED ADJUSTMENT (FAST/SLOW)
·Adjust the input signal horizontal frequency and the dot clock so that the screen display is normal.
PHASE ADJUSTMENT (UP/DOWN)
·Used to reduce image distortion or improve contrast.
HORIZONTAL POSITION ADJUSTMENT (LEFT/RIGHT)
·Used to center the on-screen image by moving it to the left or right.
VERTICAL POSITION ADJUSTMENT (UP/DOWN)
·Used to center the on-screen image by moving it up or down.
MODE ADJUSTMENT
Connecting to IBM-PC Computers
·Ordinarily, the type of input signal is detected and the correct resolution mode (Text or
Graphics) is automatically selected. However, for the following signals, set MODE to ON or
OFF to select the projectorÕs resolution mode to match the computer display mode properly.
720 dots ´ 400 lines, 720 dots ´ 350 lines (Text Mode)
640 dots ´ 400 lines, 640 dots ´ 350 lines (Graphic Mode)
¥ For graphic mode, select MODE and set the MODE to ON.
¥ For text mode, select MODE again at this time, and set MODE to OFF.
Connecting to Macintosh LC/II Series Computers
¥ When connecting to a Macintosh II with 35 kHz Dot Frequency, select MODE and set MODE
to ON.
¥ When connecting to a Macintosh LC Series computer with 34.97 kHz Dot Frequency, set
MODE to OFF.
¥ When connecting to third party video cards and other Macintosh computers, set MODE to
ON or OFF to select the correct display mode.
¥ When the input signal is automatically detected or when there is no input signal, MODE (---)
appears on the screen and the display mode cannot be changed.
 
INITIAL RESET
·To return the H-POS, V-POS, PHASE and CLOCK adjustments to their initial settings, select
RESET and then press the ENTER button.
INPUT ADJUSTMENT
1 Filter switch
In the case of very detailed computer patterns which repeat every other dot (tiling, vertical
stripes, etc.), noise may appear on the screen. Should this occur, set the FILTER switch to ON.
The pattern area will balance, and the noise will be reduced.
Note:
·Avoid displaying computer patterns which repeat every other line (horizontal stripes).
(Flickering may occur, making the picture hard to see.)
FILTER
ON
OFF
1 
						

							E-22
ON/OFF
POWER
LAMP
TEMP.
Basic Operation of the Projector
1
When the power is on, the LAMP
REPLACEMENT indicator flashes
to show the operating condition of
the lamp.
Green: Lamp is ready
Flashing green: Warming up
Red: Change bulb
ONA.C.120V
C.A.120V
OFF
1AC cord
1. Connect the AC cord.
Connect the supplied AC cord to the AC inlet on the side
of the projector .
2. Turn on the MAIN POWER.
Press the MAIN POWER switch on the side of the projec-
tor. The POWER indicator lights red and the projector
enters STANDBY mode.
3. Turn on the POWER.
Press the POWER ON/OFF button on the projector or the
POWER ON button on the remote control.
·When the power is turned off by pressing the POWER
ON/OFF button, the POWER indicator will not turn off
until the fan has stopped running.
·See page 33, ÒLamp/Maintenance IndicatorsÓ for
details.
Notes:
·When the POWER indicator is not lit, the remote control
cannot be used to operate the projector.
·If the power is turned on immediately after it has been turned
off, it may take a short while before the lamp turns on. (During
this period the LAMP REPLACEMENT indicator flashes.)
·After the projector is unpacked and turned on for the first time,
a slight odor may be emitted from the exhaust fan. This odor
will soon disappear with use.
4. E-ZOOM Function
This projector has an E-ZOOM mode which enlarges the
display when inputting an image of less than 800 ´ 600
dots in size. The E-ZOOM button on the projector or on
the remote control is used to operate E-ZOOM function.
See page 28, ÒE-ZOOM FunctionÓ for details.
Notes:
·E-ZOOM function does not operate in SVGA (800 ´ 600), Mac
16 (832 ´ 624), NTSC, PAL or SECAM INPUT mode.
·The picture size differs in RGB, NTSC, PAL and SECAM
INPUT modes.
2MAIN
POWER
switch
Projector
ON/OFFRemote control
ON/OFF
ON
OFFON/OFF
3
ON/OFF
POWER
LAMP
TEMP.
ON
OFFWhen the MAIN
POWER is on, the
POWER indicator
lights red.
2
4
E-ZOOM (ON)E-ZOOM (OFF) 
						

							E-23
On-Screen Display
LANGUAGE
:SEL.:ENTERENTER:ENDMENU
NEDERLANDS ESPAÑOL
DEUTSCH
ENGLISH
SVENSKA ITALIANO FRANÇAIS
5. Select one of eight ON-SCREEN DISPLAY
languages.
You can return to the previous screen by selecting the
uppermost item (turquoise) with the ADJUSTMENT 
/
buttons (in this case, LANGUAGE) and then pressing
the ENTER button.
The on-screen display is set to English at the factory. The
language for the unitÕs ON-SCREEN DISPLAY can be set
to English, German, Spanish, Dutch, French, Italian,
Swedish or Japanese.
Setting the ON-SCREEN DISPLAY language
1) Press the MENU button. The menu will appear on the
screen.
2) Press the ADJUSTMENT 
/ buttons to highlight the
LANGUAGE item yellow. Then press the ENTER button to
display the language menu.
3) Press the ADJUSTMENT 
/ buttons to highlight the
desired language yellow. Then press the ENTER button to
set the language. The ON-SCREEN DISPLAY is now
programmed to display in the language chosen.
6. Change the system mode.
The video input system mode is set to AUTO at the
factory, but it can be changed to a different mode if the
selected system mode is not compatible with the con-
nected audiovisual equipment (when a color image
appears in black and white, etc.).
1) Press the MENU button. The menu will appear on the
screen.
2) Press the ADJUSTMENT 
/ buttons to highlight the
ÒIMAGE ADJ.Ó yellow. Then press the ENTER button to
display the IMAGE ADJ.
3) Press the ADJUSTMENT 
/ buttons to highlight SYSTEM
yellow. Then press the ENTER button to display the
SYSTEM.
4) Press the ADJUSTMENT 
/ buttons to highlight yellow the
video system desired yellow. Then press the ENTER button
to set the system.
Notes:
·In AUTO mode, ÒPAL,Ó ÒSECAM,Ó or ÒNTSCÓ is displayed on the screen for a few
seconds when the mode is changed with the INPUT SELECT button.
·When the system mode is set to AUTO, you may not receive a clear picture due
to signal differences. If this happens, switch to the color system you are viewing.
7. Select input.
Press the INPUT SELECT button on the projector to
switch the picture input. When you press the button, the
current input mode is displayed for about 4 seconds. If
you press the button again while the input mode is
displayed, the mode changes as shown on the left.
Confirm the selected input terminal and press the INPUT
SELECT button.
Notes:
·This can be selected directly using the VIDEO, DATA1 and DATA2 buttons
on the remote control.
·In VIDEO mode, the system being received will be indicated below the
ÒVIDEOÓ display.
·When selecting RGB mode, the resolution being displayed will be indicated
under ÒRGB,Ó as shown on the left. (Refer to the second example when
connecting to Mac display.)
·When no signals are being received, ÒNO SIGNALÓ will be displayed. When
receiving a signal the projector is not preset to receive, ÒNOT REG.Ó will be
displayed. (This display function does not operate in Video mode.)
MacCOMPUTER
RGB2
For viewing the picture
from a video source
connected to: VIDEO
INPUT or S-VIDEO INPUT
COMPUTER
RGB1 On-Screen Display
:SEL.:NEXTENTER:ENDMENU
BLUE  SCREEN
BLACK  SCREEN IMAGE  ADJ.
REVERSE
INVERT INPUT  DISPLAY[OFF]
[OFF]
[
OFF]SYSTEM
[OFF] [
ON]AUTO
SYSTEM
PAL
SECAM
:SEL.:ENTERENTER:ENDMENU
NTSCÞ
On-Screen Display 
						

							E-24
8. Press INPUT CHECK.
When the INPUT CHECK button on the remote control is
pressed, the current input mode is displayed for about 4
seconds.
Note:
·The INPUT CHECK button will not function if the INPUT
DISPLAY is turned off, as described on page 31.
9. Adjust the volume.
Press the VOLUME UP-DOWN buttons on the projector
or on the remote control to adjust the volume.
MUTE
·Press the MUTE button to temporarily turn off the
sound.
·Press the MUTE button once again to turn the sound
back on.
10. To turn off the power from the projector
or remote control
The power can be temporarily turned off by pressing the
POWER ON/OFF button on either the projector or remote
control.
The POWER indicator will turn red and the cooling fan
will run for 90 seconds, then the power will turn off,
and the projector will return to STANDBY mode.
The power can be turned on again either from the
projector or remote control. When the power is turned
on, the POWER indicator and LAMP REPLACEMENT
indicator light green.
Note:
·When the MAIN POWER is off on the projector set, the power
cannot be turned on from the remote control.
VOLUME
38
The number of displayed segments
(0~60) increases or decreases as
the volume is raised or lowered.
ON/OFF
POWER
LAMP
TEMP.
Mac 
						

							E-25
Adjusting the Picture
3
·This projectorÕs picture is factory preset to standard
settings. However, you can adjust it to suit your own
preferences with the ADJUSTMENT buttons on the
projector and the remote control.
·The adjustments can be memorized in RGB 1, RGB 2
or VIDEO separately.
·Four picture modes can be adjusted: ÒPICTURE,Ó
ÒBRIGHT,Ó ÒRED,Ó  and ÒBLUE.Ó
Adjusting the Picture
1. Use the MENU button to select the mode
to be adjusted.
·When the MENU button is pressed, the MENU mode is
indicated for about 30 seconds. Press the ADJUST-
MENT 
/ buttons to select RGB1 ADJ., then press the
ENTER button.
2. Adjust the Picture
·Press the ADJUSTMENT / buttons to highlight yellow
the picture adjustment item you want to adjust.
·Press the ADJUSTMENT 
/ buttons to move the Ò  Ó
mark of the selected adjustment item to the desired
setting.
·The adjustment mode is displayed for about 30
seconds.
Description of Adjustment Items
3. Display only the item to adjust.
·Press the ADJUSTMENT / buttons to highlight yellow
the picture adjustment item you want to adjust. If you
press the ENTER button at this time, only the selected
item will be displayed.
·Press the ADJUSTMENT 
/ buttons to move the Ò  Ó
mark of the selected adjustment item to the desired
setting.
·The adjustment mode is displayed for about 30
seconds.
Notes:
·When a VIDEO signal input has been selected, only ÒPIC-
TURE,Ó ÒBRIGHT,Ó ÒCOLOR,Ó ÒTINTÓ and ÒSHARPNESSÓ can
be adjusted.
·TINT only appears in NTSC mode.
4. Press the MENU button anytime to exit
RGB ADJ.
ADJUSTMENT  button
For less contrast
For less brightness
For weaker red
For weaker blue
For less color intensity
Skin tones become purplish
For less sharpness
Selected item
PICTURE
BRIGHT
RED
BLUE
COLOR
TINT
SHARPNESS
RESET
All RGB Video Adjustment items are returned to the factory preset settings.
Note: To reset all adjustment items, select RESET in
ÒRGB1 ADJ. Ó mode and press the ENTER button.
ADJUSTMENT  button
For more contrast
For more brightness
For stronger red
For stronger blue
For more color intensity
Skin tones become greenish
For more sharpness
 +
:SEL.
:ADJ.:ENTERENTER:ENDMENU
-PICTURE 0
RGB1  ADJ.
RGB  INPUT  ADJ.
IMAGE  ADJ.
AUDIO
SYSTEM  SETUP
LANGUAGE
:SEL.:NEXTENTER:ENDMENU
1On-Screen Display
2
RGB1  ADJ.
BRIGHT
RED
BLUE
RESET
MEMORY  SELECT +
0 0
0
0
:SEL.
:ADJ.:NEXTENTER:ENDMENU
- + - + - + -
PICTURE 
						

							E-26
MEMORY  SELECT
:SEL.
:ADJ.ENTER:ENDMENU
 0 1 2 3 4 5 6 7
RESOLUTION
HOR  FREQ
VERT  FREQ
SETTING
:ENTER
Hz KHz  38
 60  800´600
MEMORY  SELECT
NON
SETTING
:SEL.
:ADJ.ENTER:ENDMENU
 0 1 2 3 4 5 6 7
:ENTER
Þ
1When RGB 1 or 2 is selected.
RGB1  ADJ.
RGB  INPUT  ADJ.
IMAGE  ADJ.
AUDIO
SYSTEM  SETUP
LANGUAGE
:SEL.:NEXTENTER:ENDMENU
RGB1  ADJ.
BRIGHT
RED
BLUE
RESET
MEMORY  SELECT +
0 0
0
0
:SEL.:NEXTENTER:ENDMENU
- + - + - + -
PICTURE
Þ
Þ
Þ
MEMORY  SELECT
SETTING
:SEL.:BACKENTER:ENDMENU
 0 1 2 3 4 5 6 7
ÞÞÞ
MEMORY  SELECT
SETTING
:SEL.
:ADJ.:ENDMENU
 0 1 2 3 4 5 6 7
PHASE
H-POS
V-POS
RESET CLOCK 0
0
0
 + - + - + -0 + -
ÞÞÞ
Computer Mode Memory Adjustments
·The projector has been preset with different modes for
use with SVGA and other compatible computers.
However, 7 memory positions are provided to store
mode adjustments.
·Each memory position can be used to store mode
adjustments to match the computer.
1. Press the ENTER button to select the
Memory Adjustment mode.
·Press the MENU button. While the MENU screen is
displayed, press the ADJUSTMENT 
/ buttons to
select ÒRGB1 ADJ.Ó Press the ENTER button. The
MENU mode changes as shown.
·While the RGB adjustment menu is displayed, press the
ADJUSTMENT 
/ buttons to select ÒMEMORY
SELECT.Ó Then press the ENTER button to change the
image.
2. Press the ADJUSTMENT / buttons.
·The screen shown on the left will appear. There are 7
memory positions.
·Press the ADJUSTMENT 
 button once to move to the
following screen. Press the ADJUSTMENT 
/ buttons
to select the number of the memory you want to adjust.
If that memory position has not been set, the screen on
the right will be displayed. If it has been set, the screen
on the left will be displayed. MEMORY No.0 cannot be
set. It contains the fixed factory preset settings.
·To make or change a setting, press the ADJUSTMENT
/ buttons to move the cursor to ÒSETTING.Ó Then
press the ENTER button to go to the next screen. (If
you do not want to make any adjustments, press the
MENU button.)
·Select the item you want to adjust by pressing the
ADJUSTMENT 
/ buttons, then use the
ADJUSTMENT 
/ buttons to make the adjustments.
When adjustments are completed, press the MENU
button. The display disappears and the adjustments are
stored in memory as a user mode. See page 25 for
details on the adjustment items.
3. Press the MENU button anytime to exit
RGB ADJ. 2 
						

							E-27
Adjusting the Audio
·The projectorÕs audio is factory preset to the standard
setting. However, you can adjust it to suit your own
preference with the ADJUSTMENT buttons on the
projector or the remote control.
·You can adjust the BALANCE, TREBLE and BASS.
·To return to the factory preset mode, press the AD-
JUSTMENT 
/ buttons to select ÒRESETÓ, then press
the ENTER button.
·Press the MENU button to select the normal screen
mode.
Adjusting the Audio
·Press the MENU button.
Select ÒAUDIOÓ with the ADJUSTMENT 
/ buttons.
Then press the ENTER button to change to the picture
indicated on the left.
·Select ÒBALANCE,Ó ÒTREBLEÓ or ÒBASSÓ with the
ADJUSTMENT 
/ buttons. Adjust the mode you want
with the ADJUSTMENT 
/ buttons.
·To return to the factory preset mode, press the AD-
JUSTMENT 
/ buttons to select RESET, then press
the ENTER button.
Description of Adjustment Items On-Screen Display
AUDIO
TREBLEBASSRESET
0 0
0
:SEL.
:ADJ.:ENDMENU
 R L + - + -
BALANCE
ADJUSTMENT  button
Increased audio from the
left speaker
Weaker treble
Weaker bassADJUSTMENT  button
Increased audio from the
right speaker
Stronger treble
Stronger bassSelected items
BALANCE
TREBLE
BASS 
						

							E-28
E-ZOOM Function
nThis projector has an E-ZOOM (640 ´ 480 dots, etc.)
mode which enlarges the display when inputting an
image of less than 800 ´ 600 dots in resolution. In the
XGA (1,024 ´ 768 dots) mode, compression enables
full-mode display.
1. Press the MENU button to select E-ZOOM
mode.
Press the MENU button. While the MENU screen is
displayed, press the ADJUSTMENT 
/ buttons to select
ÒIMAGE ADJ.Ó Then press the ENTER button to display
the IMAGE ADJ. screen as shown. Press the ADJUST-
MENT 
/ buttons to select ÒE-ZOOM,Ó and press the
ADJUSTMENT 
/ buttons to select ON. When the VGA
(640 ´ 480 dots) is input, the projector will enter E-ZOOM
mode.
E-ZOOM (ON): The screen image will be enlarged to 800 ´
600 dots.
E-ZOOM (OFF): The resolution of the image does not change.
E-ZOOM (---): No input
Notes:
·Select ON 1 or ON 2 to set the status for either a 640 ´ 400
dot image or 640 ´ 350 dot image in the E-ZOOM mode.
·In the E-ZOOM mode, an enlarged display increases the
amount of data processed on the screen and a compressed
image decreases the number of lines displayed, which may
make characters difficult to read.
2. Press the E-ZOOM button on the remote
control.
The E-ZOOM button on the remote control can be used to
select E-ZOOM and NO E-ZOOM modes.
Note:
·In SVGA (800 ´ 600 dots) or Mac 16 (832 ´ 624 dots) mode,
(---) appears, indicating the E-ZOOM function does not
operate in this mode.
3. Press the MENU button anytime to exit
E-ZOOM mode.
Notes:
·E-ZOOM function does not operate in SVGA (800 ´ 600), Mac
16 (832 ´ 624), NTSC, PAL, or SECAM INPUT modes.
·When connecting to some Mac 16 notebook computers, 832
´ 624 dot signals may be output even in 640 ´ 480 mode, thus
disabling the E-ZOOM function.
·When connecting to some SVGA notebook computers, 800 ´
600 dot signals may be output even in 640 ´ 480 mode, thus
disabling the E-ZOOM function.
E-ZOOM Function
BLACK  SCREEN IMAGE  ADJ.
REVERSE
INVERT INPUT  DISPLAY
E-ZOOM
:SEL.
:ADJ.:ENDMENU
[OFF]
[
OFF] [OFF] [ON] [
OFF]
On-Screen Display
1
2
E-ZOOM (OFF) E-ZOOM (ON) 
						

							E-29
Setting Up the System
nUsing this function, you can check the input signal,
select the remote mouse, and select DC 5V output.
Checking the system
·Press the MENU button. Select ÒSYSTEM SETUPÓ with the
ADJUSTMENT / buttons. Then press the ENTER button to
change to the picture indicated on the left.
·The current system conditions will be displayed on the screen.
·Press the MENU button to select the normal screen mode.
Note:
·In the video screen, the resolution and frequency settings will
not be displayed.
Selecting the Remote Mouse
·Press the MENU button.
·Select SYSTEM SETUP with the ADJUSTMENT / buttons.
Then press the ENTER button.
·Select ÒREMOTE MOUSEÓ and then select either Ò[AT]Ó or
Ò[98] Ówith the ADJUSTMENT 
/ buttons.
·Select [AT] when using IBM compatibles and Apple Macintosh
series.
·Select [98] when using NEC PC98 series (for Japan).
·Press the MENU button to select the normal screen mode.
Selecting DC 5V output
¥ Press the MENU button.
¥ Select ÒSYSTEM SETUPÓ with the ADJUSTMENT 
/
buttons. Then press the ENTER button.
¥ Select ÒDC 5V OUTPUTÓ and then select either ÒM.PWRÓ or
ÒLAMPÓ with the ADJUSTMENT 
/ buttons.
¥ Select ÒM.PWRÓ when you want a continuous current supply
from the DC 5V OUTPUT with the main power on.
¥ Select ÒLAMPÓ when you want a current supply from the DC
5V OUTPUT only when LAMP is set to ÒONÓ.
¥ Press the MENU button to select the normal screen mode.
Checking the Lamp Usage Time
The lamp usage time can be checked with the On-Screen
display.
1Press the INPUT SELECT button on the projector or
remote control and select RGB 1 or RGB 2 INPUT.
2Press the MENU button. While the MENU screen is
displayed, press the ADJUSTMENT 
/ buttons to
select ÒRGB1 ADJ.Ó Press the ENTER button. The
MENU mode changes as shown.
3While the RGB adjustment menu is displayed, press
the ADJUSTMENT 
/ buttons to select ÒMEMORY
SELECT.Ó Then press the ENTER button to change the
image.
4The screen shown on the left will appear.
5Press the ADJUSTMENT 
 button once to move to the
following screen.
6Using the ADJUSTMENT 
/ buttons, select memory
no. Ò1Ó and then press the ENTER button. Then,
repeating the same procedure for each number
separately, enter Ò7,Ó Ò0,Ó Ò1,Ó Ò0,Ó and Ò0.Ó
7The lamp usage time will be displayed at the On-
Screen display for approximately 30 seconds.
Functions on the Projector
RGB1  ADJ.
RGB  INPUT  ADJ.
IMAGE  ADJ.
AUDIO
SYSTEM  SETUP
LANGUAGE
:SEL.:NEXTENTER:ENDMENU
MEMORY  SELECT
SETTING
:SEL.:BACKENTER:ENDMENU
 0 1 2 3 4 5 6 7
Þ
RGB1  ADJ.
BRIGHT
RED
BLUE
RESET
MEMORY  SELECT +
0 0
0
0
:SEL.:NEXTENTER:ENDMENU
- + - + - + -
PICTURE
LAMP0000H
MEMORY  SELECT
:SEL.
:ADJ.ENTER:ENDMENU
 0 1 2 3 4 5 6 7RESOLUTION
HOR  FREQ
VERT  FREQ
SETTING
:ENTER
Hz KHz  38
 60  800´600
Þ
ÞÞ
12
3
564
7
SYSTEM  SETUP
RESOLUTION
HOR  FREQ
VERT  FREQ
REMOTE  MOUSE
:SEL.:ENDMENU
 800¥600
[AT]DC 5V OUTPUTM. PWR
:ADJ.
 60Hz  37.9 KHz
SYSTEM  SETUP
RESOLUTION
HOR  FREQ
VERT  FREQ
REMOTE  MOUSE
:SEL.:ENDMENU
 800¥600
[AT]DC 5V OUTPUTM. PWR
:ADJ.
 60Hz  37.9 KHz
SYSTEM  SETUP
RESOLUTION
HOR  FREQ
VERT  FREQ
REMOTE  MOUSE
:SEL.:ENDMENU
 800¥600
[AT]DC 5V OUTPUTM. PWR
:ADJ.
 60Hz  37.9 KHz
On-Screen Display 
						

							E-30
Using the Black Screen Function
nThis projector is equipped with a Black Screen Func-
tion. This function can be used to black out the presen-
tation image.
·Press the MENU button. While the MENU screen is
displayed, press the ADJUSTMENT 
/ buttons to
select ÒIMAGE ADJ.Ó Then press the ENTER button to
display the IMAGE ADJ. screen shown. Press the
ADJUSTMENT 
/ buttons to select ÒBLACK SCREEN,Ó
and press the ADJUSTMENT 
/ buttons to select
ON. Then press the MENU button to display the black
screen.
Note:
·When BLACK SCREEN is set to OFF, the screen will change
to the presentation image when you press the MENU button.
On-Screen Display
BLACK  SCREEN IMAGE  ADJ.
REVERSE
INVERT INPUT  DISPLAY
E-ZOOM
:SEL.
:ADJ.:ENDMENU
[OFF]
[
OFF] [OFF] [
ON]
[
OFF]
LCD Projector
BLACK SCREEN