Sharp Xg C58x Projector User Manual

Basic Operation
-37
Turning the Power off
1Press STANDBY on the projector
or 
 on the remote control,
then press that button again
while the confirmation message
is displayed, to put the projec-
tor into the standby mode.
Note
•If you accidentally pressed
STANDBY or  and do not want
to put the projector into the standby
mode, wait until the confirmation
message disappears.
•The projector cannot be operated
while a message “Shutting Down.
Please Wait.” is displayed.
2Unplug the power cord from the
AC...

Correcting Trapezoidal Distortion (Keystone Correction)
Correcting Trapezoidal
Distortion
This function allows for Keystone (On-screen
Trapezoidal Distortion) Correction.
Note
•When the image is projected either from
top or from bottom towards the screen at
an angle, the image becomes distorted
trapezoidally.
The function for correcting trapezoidal dis-
tortion is called Keystone Correction.
•The Keystone Correction can be adjusted
up to angle of approximately ±35 degrees.
1Press .
•Pressing  again while...

Basic Operation
-39
•The Digital Shift function works with BORDER, STRETCH or SMART STRETCH screen. For details, 
see page 53.
•To access Digital Shift function, press        twice.
The Digital Shift menu will appear when a compatible 16:9 signal is displayed.
Digital Shift SettingFor easier viewing, this function shifts the entire image projected on 
the screen up or down when projecting 16:9 images from DVD 
players and DTV* decoders.
*DTV is the umbrella term used to describe the new digital...

-40
Menu Bar Items
This list shows the items that can be set in the projector.
■ INPUT 1 / 2 Mode
Note
•The resolution, vertical frequency and horizontal frequency figures displayed above are for example
purposes only.
•Only when the signal type is set as “Component”, in the “Picture” menu of INPUT 1 or 2 “Color”, “Tint” and
“Sharp” are displayed.
•
Some items cannot be reset, even when “All Reset” in Options (2) has been selected. For details see page 77.
+30 –30
+30 –30
+30 –30
+30 –30
+30 –30
+30 –30...

Basic Operation
-41
■ INPUT 3 / 4 Mode
English
Deutsch
Español
Nederlands
Français
Italiano
Svenska
Português
Page 78 +30 –30
+30 –30
+30 –30
+30 –30
+30 –30
+30 –30
+30 –30
+3 –3
Main menu Sub menu Main menu Sub menu
Picture
Page 46Contrast
Bright
Color
Tint
Sharp
Red
Blue
CLR Temp
Reset
Progressive Mode
2D Progressive
3D Progressive
Film ModeOptions (2)
Page 70Lamp Life
PRJ Mode
Keylock Level
Password
Anti-Theft
All ResetFront
Ceiling + Front
Rear
Ceiling + Rear
Normal
Level A
Level B Fan ModeNormal...

This projector has two sets of menu screens that allow you to adjust the image and various
projector settings.
You can operate the menus from the projector or remote control using the following proce-
dure.
Using the Menu Screen
Menu screen for INPUT 1
or INPUT 2 RGB modeMenu screen for INPUT 3
or INPUT 4 Mode
Menu Bar
(Main Menu)
" "" "
"Menu Screen
Menu Selections
(Adjustments)
1Press .
•The menu screen is displayed.
Note
•The “Picture” menu screen for the
selected input mode is...

Basic Operation
-43
2Press 
\ \\ \
\ or 
| || |
| to select the
menu you want to adjust.
Note
•For details on the menus, see the
tree charts on pages 40 and 41.
3Press 
' '' '
' or 
" "" "
" to select the item
you want to adjust.
Note
•To display a single adjustment item,
press 
 after selecting the item.
Only the menu bar and the selected
adjustment item will be displayed.
Then if you press ' or ", the fol-
lowing item (“Red” is after “Bright”)
will be...

▼ Menu screen
Menu Selections
(Settings)
1Press .
•The menu screen is displayed.
Note
•The “Picture” menu screen for the
selected input mode is displayed.
•The on-screen display shown on the
lower right is displayed when INPUT
1 or 2 mode is selected.
2Press 
\ \\ \
\ or 
| || |
| to select the
menu you want to adjust.
Note
•For details on the menus, see the
tree charts on pages 40 and 41.
3Press 
' '' '
' or 
" "" "
" to select the
item you want to set.
Note...

Basic Operation
-45
4Press 
| || |
|.
•The cursor shifts to the sub menu.
5Press 
' '' '
' or 
" "" "
" to select the set-
ting of the item displayed in the
sub menu.
6Press .
•The item selected is set.
Note
•Some adjustment items will display
a confirmation message.
When setting an item, press  or
| to select “Yes” or “OK” and then
press 
.
7Press .
•The menu will disappear.
Sub menu 

Adjusting the Picture
You can adjust the projector’s picture to your preferences with the following picture settings.
Selected Item Description
\ button| button
Contrast
Bright
Color
Tint
Sharp
Red
Blue
CLR TempFor adjusting the contrast level
For adjusting the brightness of an image
For adjusting the color intensity of the image
For adjusting the tones of an image
For making sharper or softer the contour of an image
For adjusting the redness level
For adjusting the blue level
For adjusting the color...