Sharp Xg C58x Projector User Manual

Introduction
-7
18. Damage Requiring Service
Unplug this product from the wall outlet and refer
servicing to qualified service personnel under the
following conditions:
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have falleninto the product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the operating
instructions, as an...

-8
IMPORTANT SAFEGUARDS
Observe the following safeguards when setting up your
projector.
Caution concerning the lamp unit
■Potential hazard of glass particles if
lamp ruptures. In case of lamp rup-
ture, contact your nearest Sharp Au-
thorized Projector Dealer or Service
Center for replacement.
See “Replacing the Lamp” on page  85.
Cautions concerning the setup of
the projector
■ For minimal servicing and to maintain high image qual-
ity, SHARP recommends that this projector be installed
in an area free...

Introduction
-9
PDF operation manuals in several languages are included in the CD-ROM, so that you can
work with the projector, even if you do not have this manual. To utilize these manuals, you
need to install Adobe
® Reader® on your computer (Windows or Macintosh).
Please download Adobe
® Reader® from the Internet (http://www.adobe.com).
Accessing the PDF Manuals for Windows (For Mac, skip step 
2).
1 Insert the CD-ROM in the CD-ROM drive.
2 Double click the “My Computer” icon.
3 Double click the...

-10
Projector (Front and Top View)
Part Names
34
34
83
83
3942
35
38
50
42
35
42
25
25
ON buttonFor turning the power on.
37STANDBY buttonFor putting the projector into the standby mode.
Power indicatorIlluminates red, when the projector is in standby. 
When the power is turned  on, this indicator will illuminate green.
Lamp indicatorIlluminates green indicating normal function. Replace 
the lamp when the indicator  illuminates red.
Temperature warning  indicator
When the internal 
temperature rises,...

Introduction
-11
Projector (Rear View)
Using the Kensington Lock
•
This projector has a Kensington Security Standard connector for use with\
 a Kensington MicroSaver Security
System. Refer to the information that came with the system for instructi\
ons on how to use it to secure the
projector.
17
80
AC socket
Exhaust vent
25
17
17
Kensington Security 
Standard connector
Adjustment Feet
INPUT 2 terminal
Terminal for 
computer RGB and 
component signals.
INPUT 1 terminalTerminal for 
computer RGB and...

-12
Remote Control (Front View)
Part Names
38KEYSTONE buttonFor adjusting Keystone or Digital 
Shift setting.
23    WIRED R/C JACKFor controlling the projector by 
connecting the remote control to the 
projector.
34ON buttonF or turning the power on.
42MENU buttonFor displaying adjustment and 
setting screens.
42Adjustment buttons
( ' , " , \ , | )
For selecting menu items.
42ENTER buttonFor setting items selected or 
adjusted on the menu.
39UNDO buttonFor undoing an operation or 
returning to...

Introduction
-13
23 (7 m)30°
30 ° 45
°
Using the Remote Control
■ The remote control can be used to control the projector
within the ranges shown in the illustration.
Note
•The signal from the remote control can be reflected off a screen
for easy operation. However, the effective distance of the signal
may differ due to the screen material.
When using the remote control:
• Ensure that you do not drop the remote control or expose it to
moisture or high temperature.
• The remote control may malfunction...

-14
Accessories
Remote control
RRMCGA176WJSATwo R-6 batteries
(“AA” size, UM/SUM-3, HP-7 or similar)
Po wer cord
F or U.S., Canada, etc.
(6 (1.8 m))
QACCDA007WJPZ F
or Europe, except U.K.
(6 (1.8 m))
QACCVA011WJPZ F
or U.K. and Singapore
(6 (1.8 m))
QACCBA036WJPZ
Note
•Use the power cord that corresponds to the wall outlet in your country.
■ 3 RCA to 15-pin D-sub cable (910 (3.0 m)) AN-C3CP2 Projector manual and
technical reference
CD-ROM
UDSKAA066WJZZ
(1)
(2) (3)
Supplied accessories
Optional cable
RGB...

Connections and Setup
Connections and Setup 

-16
Connecting the Projector to Other Devices
Before Connecting
Note
•Before connecting, make sure the power cord of the projector from the AC outlet is unplugged, and that the
devices to be connected are turned off. After making all connections, turn on the projector and then the other
devices.
When connecting a computer, ensure that it is the last device to be turned on after all the connections are
made.
• Ensure that you have read the operation manuals of the devices to be connected before making...