Sharp Xg C50x Projector User Manual
Have a look at the manual Sharp Xg C50x Projector User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 615 Sharp manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Appendix -89 CONTROL CONTENTS BLACK SCREEN ON BLACK SCREEN OFF INPUT 1 INPUT 2 INPUT 3 INPUT 4 INPUT CHECK FREEZE ON FREEZE OFF AUTO SYNC STARTOK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR I I I I I I I F F AM M R R V V C R R DB B G G E E H E E JK K B B D D K Z Z S_ _ _ _ _ _ _ _ _ __ _ _ _ _ _ _ _ _ __ _ _ _ _ _ _ _ _ _1 0 1 2 1 2 0 1 0 1 BUTTONS & REMOTE CONTROL KEY COMMANDPARAMETERRETURNCONTROL CONTENTS POWER ON POWER OFF VOLUME (0 - 60) MUTE ON MUTE OFF KEYSTONE (–127 - +127) DIGITAL SHIFT (–96 - +96)OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR P P V M M K LO O O U U E NW W L T T Y DR R A E E S S_ _ _ _ _ * __ _ _ _ _ * *_ _ * _ _ * *1 0 * 1 0 * * BUTTONS & REMOTE CONTROL KEY COMMANDPARAMETERRETURN PC control A computer can be used to control the projector by connecting an RS-232C serial control cable (cross type, sold separately) to the projector. (See page 23 for connection.) Communication conditions Set the serial port settings of the computer to match that of the table. Signal format: Conforms to RS-232C standard. Baud rate: 9,600 bps Data length: 8 bits Parity bit: None Stop bit: 1 bit Flow control: None Basic format Commands from the computer are sent in the following order: command, parameter, and return code. After the projector processes the command from the computer, it sends a response code to the computer. Info •When more than one code is being sent, send each command only after the OK response code for the previous command from the projector is verified. •In the case of transmitting commands during standby, it takes a maximum of 30 seconds until the response code is received. •When the power is turned on during standby with the “POWER ON” command, wait for at least 30 seconds after the power has been turned on, and then transmit the next command. Note •When using the computer control function of the projector, the projector’s operating status cannot be read by the computer. Therefore, confirm the status by transmitting the display commands for each adjustment menu and checking the status with the on-screen display. If the projector receives a command other than a menu display command, it will execute the command without displaying the on-screen display. Commands Example: •When “BRIGHT” of INPUT 1 image adjustment is set to –10. Return code (0DH)C1 C2 C3 C4 P1 P2 P3 P4 Response code format Normal response Problem response (communication error or incorrect command) O KE R R Command 4-digitParameter 4-digit Command format Return code (0DH)Return code (0DH) (RS-232C) Specifications and Command Settings → ←RABR 1 0_–OK Projector Computer
-90 CONTROL CONTENTS INPUT 1 RESIZE : NORMAL INPUT 1 RESIZE : FULL INPUT 1 RESIZE : DOT BY DOT INPUT 1 RESIZE : STRETCH INPUT 1 RESIZE : SMART STRETCH INPUT 2 RESIZE : NORMAL INPUT 2 RESIZE : FULL INPUT 2 RESIZE : DOT BY DOT INPUT 2 RESIZE : STRETCH INPUT 2 RESIZE : SMART STRETCH INPUT 3 RESIZE : NORMAL INPUT 3 RESIZE : BORDER INPUT 3 RESIZE : STRETCH INPUT 3 RESIZE : SMART STRETCH INPUT 4 RESIZE : NORMAL INPUT 4 RESIZE : BORDER INPUT 4 RESIZE : STRETCH INPUT 4 RESIZE : SMART STRETCH RGB GAMMA : STANDARD RGB GAMMA : PRESENTATION RGB GAMMA : CINEMA RGB GAMMA : CUSTOM VIDEO GAMMA : STANDARD VIDEO GAMMA : PRESENTATION VIDEO GAMMA : CINEMA VIDEO GAMMA : CUSTOM INPUT 1 CONTRAST (–30 - +30) INPUT 1 BRIGHT (–30 - +30) INPUT 1 RED (–30 - +30) INPUT 1 BLUE (–30 - +30) INPUT 1 COLOR (–30 - +30) INPUT 1 TINT (–30 - +30) INPUT 1 SHARP (–30 - +30) INPUT 1 CLR TEMP (–3 - +3) INPUT 1 DISPLAY INPUT 1 ADJUSTMENT RESET INPUT 2 CONTRAST (–30 - +30) INPUT 2 BRIGHT (–30 - +30) INPUT 2 RED (–30 - +30) INPUT 2 BLUE (–30 - +30) INPUT 2 COLOR (–30 - +30) INPUT 2 TINT (–30 - +30) INPUT 2 SHARP (–30 - +30) INPUT 2 CLR TEMP (–3 - +3) INPUT 2 DISPLAY INPUT 2 ADJUSTMENT RESET INPUT 1 SIGNAL TYPE : RGB INPUT 1 SIGNAL TYPE : COMPONENT INPUT 2 SIGNAL TYPE : RGB INPUT 2 SIGNAL TYPE : COMPONENT INPUT 1 2D PROGRESSIVE INPUT 1 3D PROGRESSIVE INPUT 1 FILM MODE INPUT 2 2D PROGRESSIVE INPUT 2 3D PROGRESSIVE INPUT 2 FILM MODE INPUT 3 CONTRAST (–30 - +30) INPUT 3 BRIGHT (–30 - +30) INPUT 3 RED (–30 - +30)OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR R R R R R R R R R R R R R R R R R R G G G G G G G G R R R R R R R R R R R R R R R R R R R R I I I I R R R R R R V V VA A A A A B B B B B A A A A B B B B A A A A A A A A A A A A A A A A A A B B B B B B B B B B A A B B A A A B B B A A AS S S S S S S S S S S S S S S S S S M M M M M M M M P B R B C T S C R R P B R B C T S C R R S S S S I I I I I I P B RR R R R R R R R R R V V V V V V V V R R R R V V V V I R D E O I H T E E I R D E O I H T E E I I I I P P P P P P I R D_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ __ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ * * * * * * * _ _ _ * * * * * * * _ _ _ _ _ _ _ _ _ _ _ _ _ * * *_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ * * * * * * * * _ _ * * * * * * * * _ _ _ _ _ _ _ _ _ _ _ _ * * *1 5 3 2 4 1 5 3 2 4 1 3 2 4 1 3 2 4 1 2 3 4 1 2 3 4 * * * * * * * * 0 1 * * * * * * * * 0 1 1 2 1 2 0 1 2 0 1 2 * * * BUTTONS & REMOTE CONTROL KEY PICTURE COMMANDPARAMETERRETURNCONTROL CONTENTS INPUT 3 BLUE (–30 - +30) INPUT 3 COLOR (–30 - +30) INPUT 3 TINT (–30 - +30) INPUT 3 SHARP (–30 - +30) INPUT 3 CLR TEMP (–3 - +3) INPUT 3 DISPLAY INPUT 3 ADJUSTMENT RESET INPUT 4 CONTRAST (–30 - +30) INPUT 4 BRIGHT (–30 - +30) INPUT 4 RED (–30 - +30) INPUT 4 BLUE (–30 - +30) INPUT 4 COLOR (–30 - +30) INPUT 4 TINT (–30 - +30) INPUT 4 SHARP (–30 - +30) INPUT 4 CLR TEMP (–3 - +3) INPUT 4 DISPLAY INPUT 4 ADJUSTMENT RESET INPUT 3 2D PROGRESSIVE INPUT 3 3D PROGRESSIVE INPUT 3 FILM MODE INPUT 4 2D PROGRESSIVE INPUT 4 3D PROGRESSIVE INPUT 4 FILM MODE COLOR SELECTED : STANDARD COLOR SELECTED : sRGB COLOR SELECTED : CUSTOM 1 COLOR SELECTED : CUSTOM 2 COLOR SELECTED : CUSTOM 3 TARGET : RED TARGET : YELLOW TARGET : GREEN TARGET : CYAN TARGET : BLUE TARGET : MAGENTA LIGHTNESS (–30 - +30) CHROMA (–30 - +30) HUE (–30 - +30) Reset (THIS COLOR) Reset (All COLORS) CLOCK (–150 - +150) PHASE (–60 - +60) H-POSITION (–150 - +150) V-POSITION (–60 - +60) RGB INPUT DISPLAY RGB ADJUSTMENT RESET SAVE SETTING (1 - 7) SELECT SETTING (1 - 7) RGB HORIZONTAL FREQUENCY CHECK RGB VERTICAL FREQUENCY CHECK AUTO SYNC OFF NORMAL AUTO SYNC HIGH SPEED AUTO SYNC AUTO SYNC DISPLAY ON AUTO SYNC DISPLAY OFFOK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR kHz (***. * OR _) Hz (***. * OR _) OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR V V V V V V V V V V V V V V V V V V V V V V V C C C C C C C C C C C C C C C C I I I I I I M M T T A A A I IA A A A A A A B B B B B B B B B B A A A B B B M M M M M M M M M M M M M M M M N N A A A A E E F F A A A M MB C T S C R R P B R B C T S C R R I I I I I I C C C C C T T T T T T S S S R R C P H V R R M M R R D D D A AE O I H T E E I R D E O I H T E E P P P P P P S S S S S G G G G G G L C H E E L H P P E E S L Q Q J J J S S_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ * _ * _ _ _ _ _ _ _ _ _ _ _ _* * * * _ _ _ * * * * * * * _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ * * * _ _ * * * * _ _ _ _ _ _ _ _ _ _ _* * * * * _ _ * * * * * * * * _ _ _ _ _ _ _ _ 0 0 1 1 1 _ _ _ _ _ _ * * * _ _ * * * * _ _ _ _ _ _ _ _ _ _ _* * * * * 0 1 * * * * * * * * 0 1 0 1 2 0 1 2 0 1 1 2 3 1 2 3 4 5 6 * * * 1 2 * * * * 0 1 * * 1 2 0 1 2 1 0 PICTURE FINE SYNC *1 COMMANDPARAMETERRETURN C. M. S. (RS-232C) Specifications and Command Settings
Appendix -91 CONTROL CONTENTS FAO VAO SPEAKER ON SPEAKER OFF PICT IN PICT : BOTTOM RIGHT PICT IN PICT : BOTTOM LEFT PICT IN PICT : UPPER RIGHT PICT IN PICT : UPPER LEFT PICT IN PICT OFF POWER SAVE: STANDARD POWER SAVE: LOW POWER DNR : OFF DNR : LEVEL 1 DNR : LEVEL 2 DNR : LEVEL 3 AUTO SEARCH: OFF AUTO SEARCH: ON OSD DISPLAY NORMAL OSD DISPLAY LEVEL A OSD DISPLAY LEVEL B BLACK SCREEN DISPLAY ON BLACK SCREEN DISPLAY OFF VIDEO SYSTEM SELECTION : AUTO VIDEO SYSTEM SELECTION : PAL (50/60 Hz) VIDEO SYSTEM SELECTION : SECAM VIDEO SYSTEM SELECTION : NTSC4.43 VIDEO SYSTEM SELECTION : NTSC3.58 VIDEO SYSTEM SELECTION : PAL_M VIDEO SYSTEM SELECTION : PAL_N BACKGROUND SELECTION : SHARP BACKGROUND SELECTION : CUSTOM BACKGROUND SELECTION : BLUE BACKGROUND SELECTION : NONE STARTUP IMAGE SELECTION : SHARP STARTUP IMAGE SELECTION : CUSTOM STARTUP IMAGE SELECTION : NONE AUTO POWER OFF : NO USE AUTO POWER OFF : USEOK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR A A A A P P P P P T T 3 3 3 3 I I I I I I I M M M M M M M I I I I I I I A AO O S S I I I I I H H D D D D N N M M M M M E E E E E E E M M M M M M M P PU U P P N N N N N M M N N N N S S D D D B B S S S S S S S B B B B S S S O OT T K K P P P P P D D R R R R E E I I I O O Y Y Y Y Y Y Y G G G G I I I W W_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ __ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ __ _ _ _ 1 1 1 1 _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _1 2 1 0 1 2 3 4 0 0 1 0 1 2 3 0 1 1 2 0 1 0 1 2 3 4 5 6 7 1 2 3 4 1 2 3 0 1 OPTIONS (1) COMMANDPARAMETERRETURNCONTROL CONTENTS LAMP LIFE (PERCENTAGE) LAMP STATUS PRJ MODE : REVERSE OFF PRJ MODE : REVERSE ON PRJ MODE : INVERT OFF PRJ MODE : INVERT ON KEYLOCK LEVEL : NORMAL KEYLOCK LEVEL : LEVEL A KEYLOCK LEVEL : LEVEL B LANGUAGE SELECTION : ENGLISH LANGUAGE SELECTION : DEUTSCH LANGUAGE SELECTION : ESPAÑOL LANGUAGE SELECTION : NEDERLANDS LANGUAGE SELECTION : FRANÇAIS LANGUAGE SELECTION : ITALIANO LANGUAGE SELECTION : SVENSKA LANGUAGE SELECTION : LANGUAGE SELECTION : PORTUGUÊS LANGUAGE SELECTION : LANGUAGE SELECTION : MODEL NAME CHECK SERIAL NO. CHECK *2 PROJECTOR NAME SETTING 1 (First four characters) PROJECTOR NAME SETTING 2 (Middle four characters) PROJECTOR NAME SETTING 3 (Last four characters) PROJECTOR NAME CHECK0-100 (INTEGER) 0:OFF, 1:ON, 2:RETRY, 3:WAITING, 4:LAMP ERROR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR OK OR ERR MODEL NAME SERIAL NO. OK OR ERR OK OR ERR OK OR ERR PROJECTOR NAME T T I I I I K K K M M M M M M M M M M M M S P P P PL L M M M M E E E E E E E E E E E E E E N N J J J JT P R R I I Y Y Y L L L L L L L L L L L R R N N N NL S E E N N L L L A A A A A A A A A A A D D 1 2 3 0_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ * * * __ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ * * * __ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 1 1 _ _ * * * _1 1 0 1 0 1 0 1 2 1 2 3 4 5 6 7 8 9 0 1 1 1 * * * 1 OPTIONS (2) LANGUAGE COMMANDPARAMETERRETURN Note •If an underbar (_) appears in the parameter column, enter a space. If an asterisk (*) appears, enter a value in the range indicated in brackets under CONTROL CONTENTS. • *1FINE SYNC can only be set in the displayed RGB mode. •*2SERIAL NO. CHECK command is used to read out the 12 digits of serial No..
-92
1
1
1
1
1
1
1
1
1
1
1
1
1
1ON
OFF
VOLUME +
VOLUME –
MUTE
MENU
KEYSTONE
BLACK SCREEN
ENTER
RESIZE
UNDO
FREEZE
ENLARGE (+)
ENLARGE (–)0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
0
1
1
1
0
1
1
1
11
1
0
0
1
0
1
0
1
1
0
0
0
0
1
1
1
1
1
1
0
0
1
1
0
1
1
1
0
0
0
0
0
0
1
1
0
1
1
1
1
1
1
1
1
1
1
0
0
0
1
1
1
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
1
11
0
0
0
0
1
0
1
1
1
1
0
1
0
0
1
0
0
0
1
1
0
0
0
0
1
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1AUTO SYNC
∂
ƒ
ß
©
GAMMA
PinP
BACK
FORWARD
BREAK TIMER
INPUT 1
INPUT 2
INPUT 3
INPUT 40
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
1
0
1
0
1
0
1
0
0
11
0
0
0
1
0
1
1
1
0
0
1
1
1
0
1
1
0
1
0
1
1
1
1
1
1
0
0
1
1
1
0
1
0
1
1
1
0
0
0
0
0
1
1
1
1
0
0
1
0
0
1
1
1
1
1
1
0
0
0
0
0
1
1
1
1
1
1
1
11
0
0
1
1
1
1
0
0
0
0
0
0
0
1
1
1
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Wired Remote Control Terminal Specifications
Specifications of wired remote control input
•ø3.5 mm minijack
•External: +5 V (1 A)
•Internal: GND
Function and transmisson codes
Sharp remote control signal format
Transmission format: 15-bit format
Wave form of output signal: Output using Pulse Position Modulation
•t = 264 µs•Pulse carrier frequency = 455/12 kHz
•T
0 = 1.05 ms•Duty ratio = 1:1
•T
1 = 2.10 ms
Transmission control code
15 bit Example of Reverse D to D Wired remote control function code
LSB MSB
•System codes C1 to C5 are fixed at “10110”.
•Codes C14 and C15 are reverse confirmation bits, with “10” indicating “Front” and “01” indicating “Rear”.
C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 C11 C12 C13 C14
System Address
D to D Common Data Bit Reverse in DFunction Key Data BitData
Expansion
Data
Deter-
minationMaskC15
C1
1 DC2
0C3
1C4
1C5
0C6
1C7
0C8
0C9
0C10
0C11
0C12
0C13
0C14
1C15
0
C1
1 DC2
0C3
1C4
1C5
0C6
0C7
1C8
1C9
1C10
1C11
1C12
1C13
1C14
0C15
1
“0” “1” “0”
D “0” “0” “0” “1”T0T1
t
t 26.4µs
DDDDDDDDDDDDD
67.5 ms 67.5 ms
10110********10 C1 System Code C5 C6 Data Code C13 C14 C15
Appendix -93 Computer Compatibility Chart Note •This projector may not be able to display images from notebook computers in simultaneous (CRT/LCD) mode. Should this occur, turn off the LCD display on the notebook computer and output the display data in “CRT only” mode. Details on how to change display modes can be found in your notebook computer’s operation manual. •When this projector receives 640 × 350 VESA format VGA signals, “640 × 400” appears on the screen. • When receiving 1,600 × 1,200 VESA format signals, sampling occurs and part of the image may be cut as the image is displayed in 1,024 lines. •Multiple signal support Horizontal Frequency: 15–126 kHz ,Vertical Frequency: 43–200 Hz*, Pixel Clock: 12–230 MHz •Compatible with sync on green and composite sync signals •UXGA and SXGA compatible in advanced intelligent compression •AICS (Advanced Intelligent Compression and Expansion System) resizing technology The following is a list of modes that conform to VESA. However, this projector supports other signals that are not VESA standards. Upscale Tr u e 640× 350 720× 350 640× 400 720× 400 640× 480 800× 600 1,024× 76831.5 37.9 27.0 31.5 27.0 31.5 37.9 27.0 31.5 37.9 26.2 31.5 34.7 37.9 37.5 43.3 47.9 53.0 61.8 78.5 80.9 100.4 31.4 35.1 37.9 44.5 48.1 46.9 53.7 56.8 64.0 77.2 98.3 102.1 125.670 85 60 70 60 70 85 60 70 85 60 70 72 75 85 90 100 120 160 200 50 56 60 70 72 75 85 90 100 120 150 160 200✔ PC XGA SVGAVGA 50 150 35.5 40.3 48.4 56.5 58.1 60.0 68.7 73.5 77.2 80.6 98.8 113.243 50 60 70 72 75 85 90 96 100 120 140 DisplayPC/ MAC/ WSResolutionHorizontal Frequency (kHz)Vertical Frequency (Hz)VESA Standard 27.0 60 1,152× 864 1,152× 882 1,280×1,024 54.3 64.0 64.1 67.560 70 72 75 SXGA 77.3 90.2 54.8 65.9 67.4 64.0 74.685 100 60 72 74 60 70 1,280 × 1,024 Advanced Intelligent Compression 75.7 80 1,400×1,050SXGA+ DisplayPC/ MAC/ WSResolutionHorizontal Frequency (kHz)Ver tical Frequency (Hz) 78.1 74 80.0 75 91.1 85 108.4 10064.0 60 74.7 52 75.0 60 81.3 65 87.5 70 90.1 72 93.8 75 106.3 85 640× 480 34.9 67 48.4 60 60.0 75 80.0 75 46.8 7549.6 7568.5 75 78.1 72 60.0 60 85.9 8553.5 50 76.8 72 60.9 66 71.9 76 UXGA1,600 × 1,200 VGA XGA SXGA SVGA1,024× 768 800×600 832×624 1,152×870 1,280×1,024SXGA 1,280×960 1,280×1,024 1,152 ×900 HP (WS) PC (WS) WS SGI (WS) SUN (WS) PC/ MAC 21” MAC 16” PC/ MAC 13” PC/ MAC 19” SXGA PC ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ VESA Standard Upscale Tr u e Advanced Intelligent Compression Upscale Advanced Intelligent Compression Intelligent Compression * Temporary noise may be visible with vertical frequencies above 100Hz if OSD functions are activated. DTV Computer Signal480I480P540P580I580P720P1035I1080I 1080I Horizontal Frequency (kHz)15.731.533.815.631.345.033.833.8 28.1 Vertical Frequency (Hz)6060605050606060 50
-94 Troubleshooting Check •Projector power cord is not plugged into the wall outlet. •Power to the external connected devices is off. •The selected input mode is wrong. •Cables incorrectly connected to rear panel of the projector. •Remote control batteries have run out. •External output has not been set when connecting notebook computer. •The cover of the lamp unit is not installed correctly. •Cables incorrectly connected to the rear panel of the projector. •“Bright” is set to minimum position. •Picture adjustments are incorrectly set. (Video Input only) •Video input system is incorrectly set. (INPUT 1 and 2 only) •Input signal type (RGB/Component) is incorrectly set. •Adjust the focus. •The projection distance exceeds the focus range. (Computer Input only) •Perform “Fine Sync” Adjustments (“Clock” Adjustment) •Perform “Fine Sync” Adjustments (“Phase” Adjustment) •Noise will appear depending on the computer. •The “DNR” (Digital Noise Reduction) setting is not correct. •Cables incorrectly connected to rear panel of projector. •Volume is set to minimum. •The MUTE display appears. •If the picture is normal, the sound is due to cabinet shrinkage caused by a room temperature changes. This will not affect operation or performance. •See “Maintenance Indicators”. •The signal in INPUT 1 or 2 is not an RGB XGA (1024 × 768) signal. Images cannot be captured if the signals are different from the above. Problem An unusual sound is occasionally heard from the cabinet. Maintenance indicator illuminates. Image cannot be captured. Page 17 — 35 18 13 18 87 18 46 46 66 46 28 29 48 48 — 65 18 35 36 — 83 67 Sound is heard but no picture appears. Color is faded or poor. Picture is blurred; noise appears. Picture appears but no sound is heard. No picture and no sound or projector does not start.
Appendix -95 CheckProblemPage Pict in Pict does not work. Power cannot be turned on or off using the power buttons on the projector. Picture is green on INPUT 1 or 2 COMPONENT. Picture is pink (no green) on INPUT 1 or 2 RGB. Picture is dark. Picture is too bright and whitish. The VOLUME buttons on the projector do not work. A response code cannot be received when the projector was attempted to be controlled using RS-232C commands from a computer during standby.•The signal in INPUT 1 or 2 is set to a resolution that exceeds SXGA. •The signal in INPUT 1 or 2 is sending Component signals 480I, 480P, 540P, 580I, 580P, 720P, 1035I or 1080I. •The signal in INPUT 1 or 2 is set to interlace mode using RGB signals. •The Keylock level is set. If the Keylock level is set to Level B, all the buttons are locked. If the Keylock level is set to Level A, only the INPUT, VOLUME and MUTE buttons are functional. •Change the input signal type setting. •The lamp replacement indicator is blinking in red. Replace the lamp. •Picture adjustments are incorrectly set. The VOLUME buttons do not work when: (try the VOL+/– on the remote control) •when the menu is displayed •when the lens menu is displayed •when Pict in Pict is working •during Enlarge (More than double size) •a dot by dot screen resolution larger the panel resolution •In the case of transmitting RS-232C commands from a computer during standby, it takes a maximum of 30 seconds for the computer to receive the response code. Set the response code waiting time of the computer to 30 seconds or more.57 71 46 83 46 — 89 Troubleshooting
-96 For SHARP Assistance If you encounter any problems during setup or operation of this projector, first refer to the “Troubleshooting” section on pages 94 and 95. If this operation manual does not answer your question, please contact the SHARP Service departments listed below. U.S.A. Sharp Electronics Corporation 1-888-GO-SHARP (1-888-467-4277) [email protected] http://www.sharplcd.com Canada Sharp Electronics of Canada Ltd. (905) 568-7140 http://www.sharp.ca Mexico Sharp Electronics Corporation Mexico Branch (525) 716-9000 http://www.sharp.com.mx Latin America Sharp Electronics Corp. Latin American Group (305) 264-2277 [email protected] http://www.siempresharp.com Germany Sharp Electronics (Europe) GMBH 01805-234675 http://www.sharp.de U.K. Sharp Electronics (U.K.) Ltd. 0161-205-2333 [email protected] http://www.sharp.co.uk Italy Sharp Electronics (Italy) S.P.A. (39) 02-89595-1 http://www.sharp.it France Sharp Electronics France 01 49 90 35 40 [email protected] http://www.sharp.fr Spain Sharp Electronica Espana, S.A. 93 5819700 [email protected] http://www.sharp.es Switzerland Sharp Electronics (Schweiz) AG 0041 1 846 63 11 [email protected] http://www.sharp.ch Sweden Sharp Electronics ( Nordic ) AB (46) 8 6343600 [email protected] http://www.sharp.seAustriaSharp Electronics Austria (Ges.m.b.H.) 0043 1 727 19 123 [email protected] http://www.sharp.at AustraliaSharp Corporation of Australia Pty. Ltd. 1300-135-022 http://www.sharp.net.au New Zealand Sharp Corporation of New Zealand (09) 634-2059, (09) 636-6972 http://www.sharpnz.co.nz Singapore Sharp-Roxy Sales (S) Pte. Ltd. 65-226-6556 [email protected] http://www.sharp.com.sg Hong Kong Sharp-Roxy (HK) Ltd. (852) 2410-2623 [email protected] http://www.sharp.com.hk Malaysia Sharp-Roxy Sales & Service Co. (60) 3-5125678 U.A.E. Sharp Middle East Fze 971-4-81-5311 [email protected] Thailand Sharp Thebnakorn Co. Ltd. 02-236-0170 [email protected] http://www.sharp-th.com Korea Sharp Electronics Incorporated of Korea (82) 2-3660-2002 [email protected] http://www.sharp-korea.co.kr India Sharp Business Systems (India) Limited (91) 11- 6431313 [email protected]
Appendix -97 Specifications LCD Projector XG-C50X NTSC 3.58/NTSC 4.43/PAL/PAL-M/PAL-N/PAL 60/SECAM/ DTV480I/DTV480P/DTV540P/DTV580I/DTV580P/DTV720P/DTV1035I/DTV1080I LCD panel × 3, RGB optical shutter method Panel size: 0.99" (25.1 mm) (15 [H] × 20 [W] mm) No. of dots: 786,432 dots (1,024 [H] × 768 [V]) 1–1.27× zoom lens, F1.7–2.2, f = 36.5–46.3 mm AC 250 W lamp 15-pin mini D-sub connector Y: 1.0 Vp-p, sync negative, 75 Ω terminated P B: 0.7 Vp-p, 75 Ω terminated PR: 0.7 Vp-p, 75 Ω terminated 750 TV lines (DTV720P) 15-pin mini D-sub connector RGB separate/sync on green type analog input: 0–0.7 Vp-p, positive, 75 Ω terminated HORIZONTAL SYNC. SIGNAL: TTL level (positive/negative) VERTICAL SYNC. SIGNAL: Same as above RCA connector: VIDEO, composite video, 1.0 Vp-p, sync negative, 75 Ω terminated 4-pin Mini DIN connector Y (luminance signal): 1.0 Vp-p, sync negative, 75 Ω terminated C (chrominance signal): Burst 0.286 Vp-p, 75 Ω terminated 9-pin mini DIN connector 12–230 MHz 43–200 Hz* 15–126 kHz ø3.5 mm minijack: AUDIO, 0.5 Vrms, more than 47 kΩ (stereo) 3.0 W (monaural) 4 cm × 7 cm AC 100–240 V 3.4 A 50/60 Hz 340 W (Standard mode)/290 W (Low power mode) About 0.8 W (When “Mntr.out/RS232” is set to “OFF”) 1,280 BTU/hour 41°F to 104°F (+5°C to +40°C) –4°F to 140°F (–20°C to +60°C) Plastic 38 kHz 15 3⁄8"× 3 7⁄8"× 11 9⁄16" (390 (W) × 99.0 (H) × 294 (D) mm) (main body only) 151⁄2"× 4 7⁄16"× 11 5⁄8" (393 (W) × 114.0 (H) × 303.2 (D) mm) (including adjustment foot and projecting parts) 11.3 lbs. (5.1 kg) Remote control, Two R-6 batteries, Power cord for U.S., Canada etc. (11'10", 3.6 m), Power cord for Europe, except U.K. (6', 1.8 m), Power cord for U.K., Hong Kong and Singapore (6', 1.8 m), Power cord for Australia, New Zealand and Oceania (6', 1.8 m), RGB cable (9'10", 3 m), USB cable (9'10", 3 m), Computer audio cable (9'10", 3 m), DIN-D-sub RS-232C adap- tor (6 45⁄64", 15 cm), Extra air filter, Lens cap (attached), Projector manual and technical reference CD-ROM, Sharp Advanced Presentation Software CD-ROM, Operation manual, Quick reference label Lamp unit (Lamp/cage module) (BQC-XGC50X//1), Remote control (RRMCGA029WJSA), Two R-6 batteries (“AA” size, UM/SUM-3, HP-7, or similar), Power cord for U.S., Canada etc. (QACCDA010WJPZ), Power cord for Europe, except U.K. (QACCV4002CEZZ), Power cord for U.K., Hong Kong and Singapore (QACCBA012WJPZ), Power cord for Australia, New Zealand and Oceania (QACCL3022CEZZ), RGB cable (QCNWGA012WJPZ), USB cable (QCNWGA014WJPZ), Computer audio cable (QCNWGA013WJPZ), DIN-D-sub RS-232C adaptor (QCNWGA015WJPZ), Air filter (PFILDA005WJZZ), Lens cap (PCAPHA003WJSA), Projector manual and technical reference CD-ROM (UDSKAA007WJZZ), Sharp Advanced Presentation Software CD-ROM (UDSKAA005WJN1), Operation manual (TINS-A163WJZZ), Quick reference label Product type Model Video system Display method LCD panel Standard lens Projection lamp Component input signal (INPUT1/2) Horizontal resolution Computer RGB input signal (INPUT 1/2) Video input signal (INPUT 3) S-video input signal (INPUT 4) Computer control signal (RS-232C)Pixel clock Vertical frequency Horizontal frequency Audio input signal Audio output Speaker system Rated voltage Input current Rated frequency Power consumption (normal) Power consumption (standby) Heat dissipation Operating temperature Storage temperature Cabinet I/R carrier frequency Dimensions (approx.) Weight (approx.) Supplied accessories Replacement parts This SHARP projector uses a LCD (Liquid Crystal Display) panel. This very sophisticated panel contains 786,432 pix- els (× RGB) TFTs (Thin Film Transistors). As with any high technology electronic equipment such as large screen TVs, video systems and video cameras, there are certain accept-able tolerances that the equipment must conform to. This unit has some inactive pixels within acceptable toler- ances which may result in inactive dots on the picture screen. This will not affect the picture quality or the life ex- pectancy of the unit. * Temporary noise may be visible with vertical frequencies above 100Hz if OSD functions are activated. Specifications are subject to change without notice.
-98 Dimensions Side ViewSide ViewTop View Rear View Front View Bottom View 315/16 (100.5) 91/2 (241.5)15 3/8 (390) 5 (126.5)1/16 (1.5)1/16 (1.5) 3 1/8 (80)ø 67.5 4 3/8 (111.75) 2 15/16 (75) M4 M4 M4 M4 211/16(67.5) 415/16 (124.5) 5/16 (7.5)3 7/8 (98.8)8 7/16 (213.8) 11 9/16 (294) 3/16(5.2) 1/8(4) 9/16 (15) 2 1/8 (54.5)1 3/4 (44.5) 4 1/8 (104) Units: inches (mm)