Sharp Xg C430x Projector Quickstart Guide

-31
Setting up the Projector Using RS-232C or Telnet
SETUP MENU (Main Menu)
[1]IP Address
IP address settings. (Page 34)
[2] Subnet Mask
Subnet mask settings. (Page 34)
[3] Default Gateway
Default gateway settings. (Page 34)
[4]User Name (Factory default setting : Not Re-
quired)
Setting of user name for security protection. (Page 34)
[5]Password (Factory default setting : Not Required)
Setting of password for security protection. (Page 35)
[6]RS-232C Baud Rate (Factory default setting :
9600 bps)
Baud...

-32
View Setting Detail List
([V]View All Setting)
1 11 1
1Enter “v” and press the “Enter” key.
Display all setting values(*).
Enter number or symbol of item to be selected on the SETUP MENU. When setting, input the
details to be set. Setting is carried out one item at a time, and saved at the end.
▼SETUP MENU
---------------------------------SETUP MENU--------------------------------
[1]IP Address [2]Subnet Mask [3]Default Gateway
[4]User Name [5]Password
[6]RS-232C Baud Rate [7]Projector Name [8]DHCP...

-33
Save Settings and Quit
([S]Save & Quit)
Save set values and quit menu.
1 11 1
1Enter “s” and press the “Enter” key.
2 22 2
2Enter “y” and press the “Enter” key. ▼SETUP MENU
---------------------------------SETUP MENU--------------------------------
[1]IP Address [2]Subnet Mask [3]Default Gateway
[4]User Name [5]Password
[6]RS-232C Baud Rate [7]Projector Name
[8]DHCP Client[A]Advanced Setup [D]Disconnect All
[V]View All Setting [S]Save & Quit [Q]Quit Unchanged
setup>s
All Connection will be...

-34
IP Address Setting
([1]IP Address)
Setting of IP address.
1 11 1
1Enter “1” and press the “Enter” key.
2 22 2
2Enter numerical value to be set and press the
“Enter” key.
Display IP address after change (*).
Subnet Mask Setting
([2]Subnet Mask)
Setting subnet mask.
1 11 1
1Enter “2” and press the “Enter” key.
2 22 2
2Enter numerical value to be set and press the
“Enter” key.
Display subnet mask after change (*).
The setting procedure for each item will be explained. For the basic procedure, please...

-35
Password Setting
([5]Password)
Carrying out security protection using password.
1 11 1
1Enter “5” and press the “Enter” key.
2 22 2
2Enter password and press the “Enter” key.
Display set password (*).
Note
•Password can be up to 8 characters.
•You can input the characters below :
a-z, A-Z, 0-9, -, _
•In the default state, the password is not set.
RS-232C Baud Rate Set-
ting ([6]RS-232C Baud Rate)
Setting of baud rate for RS-232C terminals.
1 11 1
1Enter “6” and press the “Enter” key.
2 22 2
2Select...

-36
Disconnecting All Connec-
tions ([D]Disconnect All)
It is possible to disconnect all the TCP/IP connec-
tions currently recognized by the projector. Even if
the COM Redirect port is fixed in the Busy status
due to a problem, it is possible to force the Ready
status back by carrying out this disconnection.
1 11 1
1Enter “d” and press the “Enter” key.
2 22 2
2Enter “y” and press the “Enter” key.
Note
•If Disconnect All is performed, the connection to
the projector via network will be forcibly discon-...

-37
Carrying out Network Ping
Test
(ADVANCED[5]Network Ping Test)
It is possible to confirm that a network connection
between the projector and a computer etc. is work-
ing normally.
1 11 1
1Enter “5” and press the “Enter” key.
2 22 2
2Enter IP address of device to be tested and
press the “Enter” key.
Display entered IP address (*1).
Display test result (*2).
Note
•If the “Enter” key is pressed without entering an
IP address, the Ping destination IP address used
previously is entered.
•If there is a...

-38
Setting of Search Port
(ADVANCED[0]Search Port)
Sets the port number used when searching for the
projector from the network.
1 11 1
1Enter “0” and press the “Enter” key.
2 22 2
2Enter numerical value and press the “Enter” key.
Display set numerical value (*).
Note
•Set according to need. Normally, use with the fac-
tory default setting.
Return to Default Settings
(ADVANCED[!]Restore Default
Setting)
Returns all menu setting values to the default state.
1 11 1
1Enter “!” and press the “Enter” key.
2...

-39
1Click “Start” – “All Programs” –
“Accessories” – “Communica-
tions” – “HyperTerminal”.
•If you do not have HyperTerminal in-
stalled, see the operation manual of your
computer.
•Depending on the settings of your com-
puter, you may be required to enter your
area code and other details. Enter the
information as required.
2Enter a name in the “Name” field,
and click “OK”.
3If you are required to enter the
area code, enter it in the “Area
code” field. From the “Connect
using” drop-down menu, select...

-40
Resetting the Lamp Timer of the Projector via LAN
5Click “Properties” on the “File”
menu.
6Click the “Settings” tab, and
then click “ASCII Setup”.
7Select the check boxes next to
“Send line ends with line feeds”,
“Echo typed characters locally”,
and “Append line feeds to in-
coming line ends”, and click
“OK”.
•The LAMPRESET Properties window
appears, click “OK”.
8If a user name and/or password
is set for the projector, enter the
user name and password.
9Send the lamp reset command
“LPRE0001”.
•This...