Sharp Xg C430x Projector Quickstart Guide

							-31
Setting up the Projector Using RS-232C or Telnet
SETUP MENU (Main Menu)
[1]IP Address
IP address settings. (Page 34)
[2] Subnet Mask
Subnet mask settings. (Page 34)
[3] Default Gateway
Default gateway settings. (Page 34)
[4]User Name (Factory default setting : Not Re-
quired)
Setting of user name for security protection. (Page 34)
[5]Password (Factory default setting : Not Required)
Setting of password for security protection. (Page 35)
[6]RS-232C Baud Rate (Factory default setting :
9600 bps)
Baud rate settings for the RS-232C terminals. (Page
35)
[7] Projector Name
It is possible to assign a projector name. (Page 35)
[8] DHCP Client
DHCP Client settings. (Page 35)
[A] Advanced Setup
Enters ADVANCED SETUP MENU. (Page 36)
[D] Disconnect All
Disconnect all connections. (Page 36)
[V] View All Setting
Displays all setting values. (Page 32)
Can also be used with ADVANCED SETUP MENU.
[S] Save & Quit
Save set values and quit menu. (Page 33)
[Q]Quit Unchanged
Quit menu without saving setting values. (Page 33)
Note
•When “DHCP Client” is set to “OFF” on the pro-
jector:
IP address : 192.168.150.2
Subnet mask : 255.255.255.0
Default gateway : 0.0.0.0
ADVANCED SETUP MENU
[1]Auto Logout Time (Factory default setting : 5 min-
utes)
Setting of time until automatic disconnection of net-
work connection. (Page 36)
[2] Data Port (Factory default setting : 10002)
Setting the TCP port number used when exchang-
ing data. (Page 36)
[5] Network Ping Test
It is possible to confirm that a network connection
between the projector and a computer etc. is work-
ing normally. (Page 37)
[6] Accept IP Addr(1)
[7] Accept IP Addr(2)
[8] Accept IP Addr(3)
[9] Accept All IP Addr (Factory default setting : Ac-
cept All)
For improved security, it is possible to set up to three
IP addresses allowing connection to the projector.
Set IP addresses can be cancelled using [9] Accept
All IP Addr. (Page 37)
[0] Search Port (Factory default setting : 5006)
Setting the port number used when searching for
the projector. (Page 38)
[!] Restore Default Setting
Restores all setting values that can be set using the
menu to the default state. (Page 38)
[Q]Return to Main Menu
Return to the main SETUP MENU. (Page 38)
▼SETUP MENU▼ADVANCED SETUP MENU
---------------------------------SETUP MENU--------------------------------
[1]IP Address [2]Subnet Mask [3]Default Gateway
[4]User Name [5]Password
[6]RS-232C Baud Rate [7]Projector Name [8]DHCP Client
[A]Advanced Setup [D]Disconnect All
[V]View All Setting [S]Save & Quit [Q]Quit Unchanged
setup>******************** ADVANCED SETUP MENU ***********************
[1]Auto Logout Time [2]Data Port
[5]Network Ping Test
[6]Accept IP Addr(1) [7]Accept IP Addr(2) [8]Accept IP Addr(3)
[9]Accept All IP Addr [0]Search Port
[!]Restore Default Setting
[Q]Return to Main Menu
advanced> 
						

							-32
View Setting Detail List
([V]View All Setting)
1 11 1
1Enter “v” and press the “Enter” key.
Display all setting values(*).
Enter number or symbol of item to be selected on the SETUP MENU. When setting, input the
details to be set. Setting is carried out one item at a time, and saved at the end.
▼SETUP MENU
---------------------------------SETUP MENU--------------------------------
[1]IP Address [2]Subnet Mask [3]Default Gateway
[4]User Name [5]Password
[6]RS-232C Baud Rate [7]Projector Name [8]DHCP Client
[A]Advanced Setup [D]Disconnect All
[V]View All Setting [S]Save & Quit [Q]Quit Unchanged
setup>v
Model Name : XX-XXXX
Projector Name : XX-XXXX
MAC Address : 08:00:1F:B1:B7:74
DHCP Client : Enabled
IP Address : 192.168.150.2
Subnet Mask : 255.255.255.0
Default Gateway : Not Used
RS-232 Baud Rate : 9600 bps
Password : Not Required
**********(Advanced Status)**********
Data Port : 10002
Accept IP Address : Accept All
Auto Logout Time : 5 minutes
Search Port : 5006
1
*
Set Items
Example: When setting IP Address (change from
192.168.150.2 to 192.168.150.3)
1 11 1
1Enter “1” (number of item to be set), and press
the “Enter”  key.
Display current IP address (*1).
2 22 2
2Enter IP address to be set and press the “En-
ter” key.
Display IP address after change (*2).
3 33 3
3Enter “v” and press the “Enter” key to verify
setting detail list.
IP address is being changed (*3).
Note
•Verification of setting detail list can be omitted.
•Setting details are not effective until they have
been saved. (Page 33)
•If an invalid number is entered, an error message
(“Parameter Error!”) will be displayed. ▼SETUP MENU
---------------------------------SETUP MENU--------------------------------
[1]IP Address [2]Subnet Mask [3]Default Gateway
[4]User Name [5]Password
[6]RS-232C Baud Rate [7]Projector Name
[8]DHCP Client[A]Advanced Setup [D]Disconnect All
[V]View All Setting [S]Save & Quit [Q]Quit Unchanged
setup>1
IP Address : 192.168.150.2
Please Enter : 192.168.150.3
(change) —> 192.168.150.3
---------------------------------SETUP MENU--------------------------------
[1]IP Address [2]Subnet Mask [3]Default Gateway
[4]User Name [5]Password
[6]RS-232C Baud Rate [7]Projector Name
[8]DHCP Client[A]Advanced Setup [D]Disconnect All
[V]View All Setting [S]Save & Quit [Q]Quit Unchanged
setup>v
Model Name : XX-XXXX
Projector Name : XX-XXXX
MAC Address : 08:00:1F:B1:B7:74
IP Address : 192.168.150.3
Subnet Mask : 255.255.255.0
Default Gateway : Not Used
RS-232C Baud Rate : 9600 bps
Password : Not Required
**********(Advanced Status)**********
Data Port : 10002
Accept IP Address : Accept All
Auto Logout Time : 5 minutes
Search Port : 5006
1
2
3*1
*2
*3
Setting up the Projector Using RS-232C or Telnet 
						

							-33
Save Settings and Quit
([S]Save & Quit)
Save set values and quit menu.
1 11 1
1Enter “s” and press the “Enter” key.
2 22 2
2Enter “y” and press the “Enter” key. ▼SETUP MENU
---------------------------------SETUP MENU--------------------------------
[1]IP Address [2]Subnet Mask [3]Default Gateway
[4]User Name [5]Password
[6]RS-232C Baud Rate [7]Projector Name
[8]DHCP Client[A]Advanced Setup [D]Disconnect All
[V]View All Setting [S]Save & Quit [Q]Quit Unchanged
setup>s
All Connection will be disconnect.
Continue(y/n)? y
Apply New setting...Done.
1
2
Quit without Saving Set-
tings ([Q]Quit Unchanged)
Quit menu without saving setting values.
1 11 1
1Enter “q” and press the “Enter” key.
2 22 2
2Enter “y” and press the “Enter” key. ▼SETUP MENU
---------------------------------SETUP MENU--------------------------------
[1]IP Address [2]Subnet Mask [3]Default Gateway
[4]User Name [5]Password
[6]RS-232C Baud Rate [7]Projector Name
[8]DHCP Client[A]Advanced Setup [D]Disconnect All
[V]View All Setting [S]Save & Quit [Q]Quit Unchanged
setup>q
Quit Without Saving(y/n)? y
Setting Unchanged.
1
2
Setting up the Projector Using RS-232C or Telnet 
						

							-34
IP Address Setting
([1]IP Address)
Setting of IP address.
1 11 1
1Enter “1” and press the “Enter” key.
2 22 2
2Enter numerical value to be set and press the
“Enter” key.
Display IP address after change (*).
Subnet Mask Setting
([2]Subnet Mask)
Setting subnet mask.
1 11 1
1Enter “2” and press the “Enter” key.
2 22 2
2Enter numerical value to be set and press the
“Enter” key.
Display subnet mask after change (*).
The setting procedure for each item will be explained. For the basic procedure, please refer
to “Set Items” on page 32.
setup>1
IP Address :192.168.150.2
Please Enter :192.168.150.3
(change)      —>  192.168.150.31
2
*
setup>2
Subnet Mask :255.255.255.0
Please Enter :255.0.0.0
(change)      —>  255.0.0.01
2
*
Default Gateway Setting
([3]Default Gateway)
Setting default gateway.
1 11 1
1Enter “3” and press the “Enter” key.
2 22 2
2Enter numerical value to be set and press the
“Enter” key.
Display gateway address after change (*).
Note
•If the values for IP Address, Subnet Mask or Gate-
way of the projector have been changed via Telnet,
the computer cannot be connected to the projector
depending on the computer’s network settings.
User Name Setting
([4]User Name)
Carrying out security protection using user name.
1 11 1
1Enter “4” and press the “Enter” key.
2 22 2
2Enter user name and press the “Enter” key.
Display set user name (*).
Note
•User name can be up to 8 characters.
•You can input the characters below :
a-z, A-Z, 0-9, -, _
•In the default state, user name is not set.
setup>3
note: “0.0.0.0” means “Using no default gateway.”
Gateway Address :0.0.0.0
Please Enter :192.168.150.1
(change)          —>  192.168.150.11
2
*
setup>4
User Name :
Please Enter : XX-XXXX
(change)        —>   XX-XXXX1
2
*
Setting up the Projector Using RS-232C or Telnet 
						

							-35
Password Setting
([5]Password)
Carrying out security protection using password.
1 11 1
1Enter “5” and press the “Enter” key.
2 22 2
2Enter password and press the “Enter” key.
Display set password (*).
Note
•Password can be up to 8 characters.
•You can input the characters below :
a-z, A-Z, 0-9, -, _
•In the default state, the password is not set.
RS-232C Baud Rate Set-
ting ([6]RS-232C Baud Rate)
Setting of baud rate for RS-232C terminals.
1 11 1
1Enter “6” and press the “Enter” key.
2 22 2
2Select and enter the number 0, 1 or 2 and
press the “Enter” key.
Display set baud rate (*).
Note
•Set the projector’s baud rate to the same rate as
that used by the computer.
setup>5
Password :
Please Enter : sharppj
(change)        —>   sharppj1
2
*
Projector Name Setting
([7]Projector Name)
It is possible to assign a projector name.
1 11 1
1Enter “7” and press the “Enter” key.
2 22 2
2Enter projector name.
Display set projector name (*).
Note
•Projector name can be up to 12 characters.
•You can input the characters below :
A-Z, 0-9, -, _, (,), space
(When “a-z” are input, they are converted to “A-Z”
automatically.)
•It is the same as the name which can be con-
firmed or set, using RS-232C commands “PJN0”,
“PJN1”, “PJN2” and “PJN3”.
DHCP Client Setting
([8]DHCP Client)
Setting DHCP Client to “ON” or “OFF”.
Example: When setting DHCP Client to “ON”
1 11 1
1Enter “8” and press the “Enter” key.
2 22 2
2Enter “1” and press the “Enter” key.
Display the obtained values (*).
setup>6
0 ...  9600 bps
1 ...   38400 bps
2 ... 115200 bps
Baud Rate Select[0-2] :2
RS-232C Baud Rate : 115200 bps1
2
*
setup>7
Projector Name : XX-XXXX
Please Enter : MY XX-XXXX
(change)       —>   MY XX-XXXX1
2
*
setup>8
note: It sets DHCP Client.
0 ... OFF
1 ... ON
DHCP Select[0-1] : 1
DHCP Client : ON
Success get data from DHCP server.
[MAC Address      
 ] : [08:00:1F:B1:B7:74]
[IP Address           ] : [192.168.150.2]
[Subnet Mask        ] : [255.255.255.0]
[Default Gateway   ] : [0.0.0.0]
[DHCP IP Address] : [192.168.150.1]
1
2
*
Setting up the Projector Using RS-232C or Telnet 
						

							-36
Disconnecting All Connec-
tions ([D]Disconnect All)
It is possible to disconnect all the TCP/IP connec-
tions currently recognized by the projector. Even if
the COM Redirect port is fixed in the Busy status
due to a problem, it is possible to force the Ready
status back by carrying out this disconnection.
1 11 1
1Enter “d” and press the “Enter” key.
2 22 2
2Enter “y” and press the “Enter” key.
Note
•If Disconnect All is performed, the connection to
the projector via network will be forcibly discon-
nected.
Entering ADVANCED
SETUP MENU
([A]Advanced Setup)
Enters ADVANCED SETUP MENU.
1 11 1
1Enter “a” and press the “Enter” key.
Setting Auto Logout Time
(ADVANCED[1]Auto Logout Time)
If there is no input after a fixed time, the projector
automatically disconnects network connection using
the Auto Logout function. It is possible to set the time
until the projector is automatically disconnected in
units of a minute (from 1 to 65535 minutes).
1 11 1
1Enter “1” and press the “Enter” key.
2 22 2
2Enter numerical value and press the “Enter” key.
Display set numerical value (*).
Note
•If the set value is made 0, the Auto Logout func-
tion is disabled.
•
If an invalid number is entered, an error message
(“Parameter Error!”) will be displayed and the
screen returns to the ADVANCED SETUP MENU.
Data Port Setting
(ADVANCED[2]Data Port)
Setting of TCP port number. It is possible to set in
the range of 1025 to 65535.
1 11 1
1Enter “2” and press the “Enter” key.
2 22 2
2Enter numerical value and press the “Enter” key.
Display set numerical value (*).
Note
•Set according to need. Normally, use with the fac-
tory default setting.
setup>d
Disconnect All  Connections(y/n)?y
Now Disconnecting...1
2
setup>a
******************** ADVANCED SETUP MENU ***********************
[1]Auto Logout Time [2]Data Port
[5]Network Ping Test
[6]Accept IP Addr(1) [7]Accept IP Addr(2) [8]Accept IP Addr(3)
[9]Accept All IP Addr [0]Search Port
[!]Restore Default Setting
[Q]Return to Main Menu
advanced>1
advanced>1
Valid range : 0 to 65535 (minute)
note: if you enter “0”, auto logout function will be disable.
Auto Logout Time : 5
Please Enter :15
(change)        —>  151
2
*
advanced>2
Valid range :1025 to 65535
Data Port :10002
Please Enter :10005
(change)          —>  100051
2
*
Setting up the Projector Using RS-232C or Telnet 
						

							-37
Carrying out Network Ping
Test
(ADVANCED[5]Network Ping Test)
It is possible to confirm that a network connection
between the projector and a computer etc. is work-
ing normally.
1 11 1
1Enter “5” and press the “Enter” key.
2 22 2
2Enter IP address of device to be tested and
press the “Enter” key.
Display entered IP address (*1).
Display test result (*2).
Note
•If the “Enter” key is pressed without entering an
IP address, the Ping destination IP address used
previously is entered.
•If there is a fault with the connection, “Error: No
answer” is displayed after a 5 second retry. In this
case, please confirm the settings for the projector
and the computer, and contact your network ad-
ministrator.
Setting of Accept IP Ad-
dress 
(ADVANCED[6]Accept IP
Addr(1) - [8]Accept IP Addr(3))
It is possible to improve security of the projector by
allowing connection from only a prescribed IP ad-
dress. It is possible to set up to three IP addresses
allowing connection to the projector.
1 11 1
1Enter “6”, “7” or “8” and press the “Enter” key.
2 22 2
2Enter numerical value and press the “Enter” key.
Display set numerical value (*).
Note
•To invalidate the Accept IP Address being cur-
rently set, enter “0.0.0.0”.
•If there is one or more Accept IP Addr being set,
no connections are allowed from IP addresses
that are not yet set. They can be cancelled using
[9]Accept All IP Addr.
Accepting All IP Addresses
(ADVANCED[9]Accept All IP Addr)
Removes IP addresses set with “Accept IP Addr”.
1 11 1
1Enter “9” and press the “Enter” key.
2 22 2
2Enter “y” and press the “Enter” key.
Note
•At the point in time where “y” was entered, the
numerical values for Accept IP Addr(1)-(3) are
reset to “0.0.0.0”.
•If “n” is entered, setting is not altered.
advanced>5
Ping dest IP addr :192.168.150.1
Please Enter :192.168.150.152
(change)         —>  192.168.150.152
32 bytes from 192.168.150.152: icmp_seq = 1, time = 0 ms
32 bytes from 192.168.150.152: icmp_seq = 2, time = 0 ms
32 bytes from 192.168.150.152: icmp_seq = 3, time = 0 ms
32 bytes from 192.168.150.152: icmp_seq = 4, time = 0 ms1
2
*1
*2advanced>6
Accept IP Addr(1) : 0.0.0.0
Please Enter : 192.168.150.152
(change)         —>   192.168.150.1521
2
*
advanced>9
Accept All  IP Addresses(y/n)?  y1
2
Setting up the Projector Using RS-232C or Telnet 
						

							-38
Setting of Search Port
(ADVANCED[0]Search Port)
Sets the port number used when searching for the
projector from the network.
1 11 1
1Enter “0” and press the “Enter” key.
2 22 2
2Enter numerical value and press the “Enter” key.
Display set numerical value (*).
Note
•Set according to need. Normally, use with the fac-
tory default setting.
Return to Default Settings
(ADVANCED[!]Restore Default
Setting)
Returns all menu setting values to the default state.
1 11 1
1Enter “!” and press the “Enter” key.
2 22 2
2Enter “y” and press the “Enter” key.
Note
•If the values for IP Address, Subnet Mask or Gate-
way of the projector have been returned to the
default settings via Telnet, the computer cannot
be connected to the projector depending on the
computer’s network settings.
Return to Main Menu
(ADVANCED[Q]Return to Main Menu)
Returns to the main SETUP MENU.
1 11 1
1Enter “q” and press the “Enter” key.
Returns to the SETUP MENU.
advanced>0
Please Enter Port Number for Search from Computer.
Valid range : 1025 to 65535
Search Port : 5006
Please Enter : 5004
(change)         —>   50041
2
*
advanced>!
Restore All Setting to Default(y/n)? y
— User Setting Initialized —1
2
advanced>q
---------------------------------SETUP MENU--------------------------------
[1]IP Address [2]Subnet Mask [3]Default Gateway
[4]User Name [5]Password
[6]RS-232C Baud Rate [7]Projector Name [8]DHCP Client
[A]Advanced Setup [D]Disconnect All
[V]View All Setting [S]Save & Quit [Q]Quit Unchanged
setup>1
Setting up the Projector Using RS-232C or Telnet 
						

							-39
1Click “Start” – “All Programs” –
“Accessories” – “Communica-
tions” – “HyperTerminal”.
•If you do not have HyperTerminal in-
stalled, see the operation manual of your
computer.
•Depending on the settings of your com-
puter, you may be required to enter your
area code and other details. Enter the
information as required.
2Enter a name in the “Name” field,
and click “OK”.
3If you are required to enter the
area code, enter it in the “Area
code” field. From the “Connect
using” drop-down menu, select
“TCP/IP (Winsock)”, and click
“OK”.
4Enter the IP address of the pro-
jector in the “Host address” field
(see “TCP/IP” on the “Network”
menu of the projector), and en-
ter the data port of the projector
in the “Port number” field
(“10002” is the factory default
setting), and click “OK”.
Resetting the Lamp Timer of the Projector via LAN
When the projector is connected to a network, you can use HyperTerminal or a similar com-
munications program to send a command to reset the lamp timer. The example below uses
Windows
® XP as the operating system.
Select
“TCP/IP (Winsock)” 
						

							-40
Resetting the Lamp Timer of the Projector via LAN
5Click “Properties” on the “File”
menu.
6Click the “Settings” tab, and
then click “ASCII Setup”.
7Select the check boxes next to
“Send line ends with line feeds”,
“Echo typed characters locally”,
and “Append line feeds to in-
coming line ends”, and click
“OK”.
•The LAMPRESET Properties window
appears, click “OK”.
8If a user name and/or password
is set for the projector, enter the
user name and password.
9Send the lamp reset command
“LPRE0001”.
•This command can only be sent when
the projector is in standby mode.
•When “OK” is received, this indicates
that the lamp was successfully reset.
10Close HyperTerminal.