Sharp Xg C330x Projector Quickstart Guide

-11
RS-232C Terminal:9-pin mini DIN female connector
Pin No. Signal Name I/O Reference
1Not connected
2RDReceive Data Input Connected to internal circuit
3SDSend Data Output Connected to internal circuit
4Not connected
5SGSignal Ground Connected to internal circuit
6Not connected
7RSRequest to Send Connected to CS in internal circuit
8CSClear to Send Connected to RS in internal circuit
9Not connected
RS-232C Terminal: 9-pin D-sub male connector of the DIN-D-sub RS-232C adaptor
Pin No. Signal Name I/O...

-12
Connecting Pin Assignments
1724
19168
Pin No. Signal1T.M.D.S. Data 2–
2T .M.D.S. Data 2+
3T .M.D.S. Data 2 Shield
4 Not connected
5 Not connected
6 DDC Clock
7 DDC Data
8 Not connected
9T .M.D.S. Data 1–
10 T.M.D.S. Data 1+
11 T.M.D.S. Data 1 Shield
12 Not connected
D VI-D Input Terminal
Pin No. Signal13 Not connected
14 +5 V Power
15 Ground
16 Hot Plug Detect
17 T.M.D.S. Data 0–
18 T.M.D.S. Data 0+
19 T.M.D.S. Data 0 Shield
20 Not connected
21 Not connected
22 T.M.D.S. Clock Shield
23 T.M.D.S....

-13
Computer control
A computer can be used to control the projector by connecting an RS-232C serial control cable (cross type,
commercially available) to the projector. (See page 27 of the projector’s operation manual for connection.)
Communication conditions
Set the serial port settings of the computer to match that of the table.
Signal format: Conforms to RS-232C standard. Parity bit: None
Baud rate*: 9,600 bps / 38,400 bps / 115,200 bps Stop bit: 1 bit
Data length: 8 bits Flow control: None
*Set the...

-14
RS-232C Specifications and Commands
Commands
Example: When turning on the projector, make the following setting.
→
←POWR _ 1__OK
Projector Computer
CONTROL CONTENTS
Power ONStandby mode
(or 40-second startup time)COMMAND PARAMETERRETURN
Power Off
Power On
Power Status
Projector Condition
Lamp Status
Lamp Power Status
Lamp Quantity
Lamp Usage Time (Hour)
Lamp Life (Percentage)
Model Name Check
Model Name Check
Serial No. Check *1
Projector Name Setting 1 (First four characters) *2
Projector Name...

-15
RS-232C Specifications and Commands
CONTROL CONTENTSPower ONStandby mode
(or 40-second startup time)COMMAND PARAMETERRETURN
S-Video Resize : Normal
S-Video Resize : Stretch
S-Video Resize : Border
S-Video Resize : Area Zoom
S-Video Resize : V-Stretch 
Video Resize : Normal
Video Resize : Stretch
Video Resize : Border
Video Resize : Area Zoom
Video Resize : V-Stretch
COMPUTER 1 Adjustment Reset
COMPUTER 2 Adjustment Reset
DVI Adjustment Reset
S-VIDEO Adjustment Reset
VIDEO Adjustment Reset
COMPUTER 1...

-16
RS-232C Specifications and Commands
CONTROL CONTENTSPower ONStandby mode
(or 40-second startup time)COMMAND PARAMETERRETURN
DVI Progressive : 2D
DVI Progressive : 3D
DVI Signal Type : D. PC RGB
DVI Signal Type : D. PC Comp.
DVI Signal Type : D. Video RGB
DVI Signal Type : D. Video Comp.
DVI Dynamic Range : Standard
DVI Dynamic Range : Enhanced
S-Video Picture Mode : Standard
S-Video Picture Mode : Presentation
S-Video Picture Mode : Movie
S-Video Picture Mode : Game
S-Video Contrast (– 30 - + 30)...

-17
RS-232C Specifications and Commands
PJLinkTM Compliant:
This product conforms with the PJLink standard Class 1 and all Class 1 commands are implemented.
This product confirms with the PJLink standard specification version 1.00.
CONTROL CONTENTS
Power ONStandby mode
(or 40-second startup time)COMMAND PARAMETERRETURN
Internal Speaker : Off
Internal Speaker : On
Audio  Out : FAO
Audio  Out : VAO
PRJ Mode : Reverse Off
PRJ Mode : Reverse On
PRJ Mode : Invert Off
PRJ Mode : Invert On
Fan Mode : Normal
Fan...

-18
Page 19
1.Connecting the projector to a computer
Setting up the Projector Network Environment
This section describes the basic procedure for using the projector via the network.
If the network is already constructed, the projector’s network settings may need to be changed. Please
consult your network administrator for assistance with these settings.
You can make network settings both on the projector and on the computer. The following procedure is for
making settings on the computer.
Network settings...

-19
Setting up the Projector Network Environment
1. Connecting the Pro-
jector to a Computer
Establishing a one-to-one connection from the
projector to a computer. Using a LAN cable
(Category 5, cross-over type) you can config-
ure the projector via the computer.
1Disconnect the computer’s LAN
cable from the existing network.
2Connect a LAN cable (a UTP
cable, Category 5, cross-over
type) to the projector’s LAN ter-
minal and connect the other end
of the cable to the computer’s
LAN terminal.
3Plug the...

-20
Setting up the Projector Network Environment
2. Setting an IP Address
for the Computer
The following describes how to make settings
in Windows® XP (Professional or Home Edi-
tion).
1Log on the network using the
administrator’s account for the
computer.
2Click “Start”, and click “Control
Panel”.
3Click “Network and Internet Con-
nections”, and click “Network
Connections” in the new window.
•This manual uses examples to explain
the operations in Category View. If you
are using Classic View,...