Sharp Ux 510 Plain Paper Fax Operation Manual

1Press the keys shown at right.
OPTION SETTING will appear in the
display.FUNCTION4
2Press the keys shown at right.
DISTINCTIVE RING will appear in the
display.
3Select a ring pattern by entering the ap-
propriate number (1 to 5 as shown in
the list on the previous page).
STOP
1
(Example)
4Press the STOP key.
Note:If you are using an answering machine with your distinctive ring serv-
ice, the answering machine must be connected to a separate wall jack. Do not
connect it directly to your fax.
Chapter 2...

Storing Numbers for Automatic Dialing
Automatic dialing is a quick and convenient way of dialing which is done by
either pressing a Rapid Key (Rapid Key Dialing), or pressing the SPEED DIAL
key and entering a 2-digit number (Speed Dialing). Automatic dialing can be
used for both fax transmissions and voice calls.
To use automatic dialing, you must first store the full number in your fax and as-
sign a 2-digit Speed Dial number to it. You can also enter a name which appears
in the display when the number...

3Enter a two-digit number (from 01 to
99) by pressing the number keys. This
will be the Speed Dial number.
(Example)
4Enter the fax or voice number by press-
ing the number keys (max. of 32 digits in-
cluding pauses).
(Example)
5Press the START key.
6Enter the name of the location or party
by pressing the appropriate number key
for each letter several times until the let-
ter appears in the display (max. of 20
characters). (See Entering Letters for
Names in this chapter for more details.)
If you don’t...

Clearing numbers
1Press the keys shown at right.
FAX/TEL. # MODE will appear in the
display.
2Press 2 to select CLEAR.
3Enter the Speed Dial number that you
want to clear by pressing the number
keys.
(Example)
4Press the START key.
5Return to Step 3 to clear another num-
ber, or press STOP to exit.
Step 3 or
Making changes
To make changes in a number previously stored, repeat the storing procedure.
Select the Speed Dial number for which you want to make changes in Step 3,
and then change the number...

Storing numbers in Group Keys
Group Keys allow you to dial a group of fax numbers by simply pressing the ap-
propriate Group Key once. They are convenient for the Broadcasting function,
which is used to transmit a document to a group of fax machines.
Rapid Keys 18/G1 and 19/G2 can be programmed as Group Keys. To program
or clear a Group Key, follow the steps below. Note that one key cannot be simul-
taneously programmed as both a Rapid Key and a Group Key.
¨Up to 20 fax numbers can be stored in one Group...

Volume Adjustment
You can adjust the volume of the speaker, handset, and ringer using the UP and
DOWN keys on the operation panel.
Speaker
The speaker has three volume levels: HIGH, MIDDLE, and LOW. To adjust the
volume of the speaker, press the SPEAKER key and then press the UP or
DOWN key until the desired level appears in the display. Press the SPEAKER
key again to turn the speaker off.
Handset
The handset receiver has two volume levels: HIGH and MIDDLE. To adjust the
volume of the handset receiver,...

5.8
(148 mm)
8.5(216 mm)
 14 lbs.36 lbs.5.0(128 mm)39.4(1.0 m)
(52 g/m2)
(135 g/m2)
5.8
(148 mm)8.5(216 mm)
5.0(128 mm)11(279 mm)
(75 g/m2)
 14 lbs.20 lbs.
(52 g/m2)
Chapter3Sending
Documents
Transmittable Documents
Your fax can transmit most standard office documents. Specific guidelines are
as follows:
Size and weight
The size and weight of documents which you can load in the document feeder
depend on whether you load one sheet at a time or several sheets at once.
One sheet at a time:
Several sheets at...

Loading the Document
Up to 20 pages can be placed in the feeder at one time. The pages will be auto-
matically fed into the fax starting from the page on the bottom.
¨If you need to send or copy more than 20 pages, place the additional pages
gently and carefully in the feeder just before the last page is scanned. Do
not try to force them in, as this may cause double-feeding or jamming.
¨If your document consists of several large or thick pages which must be
loaded one at a time, insert each page into the...

Optional Transmission Settings
If desired, there are several transmission settings which are possible before dial-
ing and transmitting the document.
Note:To make the settings, the document must first be loaded in the feeder.
Resolution
Your fax has 4 resolution settings. If you do not make a setting, the fax will auto-
matically send the document in STANDARD resolution.
STANDARD: Use STANDARD for ordinary documents. This setting
gives you the fastest and most economical transmission.
FINE: Use FINE for...

Cover Sheet
You can have your fax generate a cover sheet and send it as the last page of the
transmission. The cover sheet includes the date and time, the sender’s name and
number, and the receiver’s name and number if an automatic dialing number is
used. The total number of pages sent is indicated on the bottom.
¨Your name and number must be programmed in order for them to appear
on the cover sheet. (See Entering Your Name and Fax Number in Chap-
ter 2.)
To include a cover sheet with each transmission,...