Sharp Projector Pg M25x User Manual

							Basic Operation
-37
Z
o
o
m
 
in
Z
o
o
m
 o
u
t
Selecting the On-screen
Display Language
•The on-screen display language of the pro-
jector can be set to English, German, Span-
ish, Dutch, French, Italian, Swedish, Por-
tuguese, Chinese, Korean or Japanese.
•The following explanation uses operations
from the projector as example.
1Press .
•The menu will be displayed.
2Press  or  to select
“Language”.
3Press  or  to select
the desired language, and then
press 
.
4Press .
•The desired language will be set as
the on-screen display.
Adjusting the Lens
The image is focused and adjusted to the
desired size using the focus ring or zoom
knob on the projector.
1The focus is adjusted by rotat-
ing the focus ring.
2Zooming is adjusted  by mov-
ing the zoom knob.
Zoom knob
Focus ring
PG-M25X#E#p33_49.p6502.4.29, 3:12 PM 37 
						

							Correcting the Trapezoidal Distortion (Keystone Correction)
Correcting the Trap-
ezoidal Distortion
This function allows for Keystone (On-screen
Trapezoidal Distortion) Correction.
The following explanation uses operations
from the projector as example.
Note
•Keystone Correction is the correction for
trapezoidal distortion that occurs when
the image is positioned away from the
center axis of the screen.
•
The trapezoidal distortion can be corrected
up to an angle of approximately ±35 degrees.
•The projector can be adjusted to a
maximum of 10 degrees.
1Press .
•Pressing  again while the BORDER,
STRETCH or SMART STRETCH
screen is displayed will star t the Digital
Shift function. See page 39.
•You can also use  on the
GyroRemote.
2Press    or  to
adjust the Keystone correction.
•If you want to make more detailed cor-
rections, press 
 to display the test
pattern, and then press 
  
or  to make the adjustments.
•Adjustments can also be done using
the 
 or  button on the
GyroRemote.
Note
•Since the trapezoidal distortion of
the image can be corrected up to
an angle of approximately ±35 de-
grees, the actual screen can be di-
agonally set up to that angle as well.
•Press 
 to cancel Keystone
Correction.
•You can delete using the 
 button
on the GyroRemote.
LENS button
Adjustment
buttons
(
"'\ | "'\ |"'\ | "'\ |
"'\ |)
UND)O
button
ENTER button
Normal screenKeystone Correction screen
Compresses upper side.
Compresses lower side.
-38
PG-M25X#E#p33_49.p6502.4.29, 3:12 PM 38 
						

							Basic Operation
-39
3Press .
Note
•You can use the same settings used
in NORMAL mode 4:3 for 16:9.
•Straight lines or the edges of images
may appear jagged while adjusting
the image.
•The Digital Shift function is
displayed when a wide screen from
video or digital video is displayed.
When using the GyroRemote:
•You can use the                 button to move the screen up or down.
•Press         to return to the original position.
•The Digital Shift function works with STRETCH or SMART STRETCH screen. For details, see page 83.
Digital Shift SettingFor easier viewing, this function shifts the image projected on the 
screen up or down eliminating either the upper or lower black band 
found in 16:9 and other wide aspect ratios.
Note
UNDO button
Press          to move the 
projected image upwards.
Press          to reset the 
image.
Press          to move the 
projected image 
downwards.
Press          to reset the 
image.
PG-M25X#E#p33_49.p6502.4.29, 3:12 PM 39 
						

							-40
Using the GyroRemote
Before Using the
GyroRemote
Make sure that the antenna on the projector
is fully extended before operating the projector
with the GyroRemote.
Info
•The control range under actual operating
conditions may be less than optimum
depending on where the projector is
placed and the radio signal environment.
•If the GyroRemote does not operate, press
 on the GyroRemote.
Gesture Operation
(Selecting OSD Menus,
Operating Presentation Tools)
The GyroRemote accurately tracks your hand
movements in the air while holding it and
performs the following operations.
•Bright and easy-to-see screen pointer.
(See page 44.)
•Operate the menu with a simple wave
of the hand. (See pages 54, 55.)
•Press ASSIGN to toggle and display
the 5 “Button ASSIGN” lists one-by-
one.
Each “Button ASSIGN” list has 4
selection items. (See page 41.)
•With the GyroRemote you can operate
your computer with the same feeling
as operating a normal mouse by
connecting the projector and a
computer using the included USB
cable. (See page 47.)
Function 1
buttonFunction 2
button
Function 4
buttonASSIGN
button
Mouse Control Function 3
button
PG-M25X#E#p33_49.p6502.4.29, 3:12 PM 40 
						

							Basic Operation
-41
Function Assign
The Button Assign function on the
GyroRemote, consists of 5 items (1/5 to 5/5)
and within each, there are 4 function buttons
(Function 1 to 4.)
Selecting the function buttons for assigning
items is done via the projector.
1Press  on the GyroRemote.
•Each time you press  the Button
Assign selection changes as shown
below.
1/52/53/54/55/5
2Press 
•The Button Assign selection display
disappears.
Function 1 button
Function 2 button
Function 3 button
Function 4 button
Function 1 buttonFunction 2
button
Function 3
button
Function 4
button
ASSIGN buttonUNDO
button
All Button Assign selections
•The list can also be displayed using 
: ASSIGN button: LEFT-CLICK/ENTER button: RIGHT-CLICK/UNDO button
PG-M25X#E#p33_49.p6502.4.29, 3:12 PM 41 
						

							Using the GyroRemote (cont.)
GyroRemote Channel
Setting
The GyroRemote uses radio signals, which
can receive interference under certain
conditions. To avoid interference, when using
multiple GyroRemotes, register a different
channel for each GyroRemote in the projector.
The GyroRemote has 8 channels for U.S.,
Canada, etc. and 4 channels for Europe,
Australia, Oceania and Aisa.
1Press  located on the
GyroRemote.
•You can also confirm the RF channel
by the number of times the LED
indicator flashes.
(Ex: RF Channel 3 if the LED indicator
flashes 3 times.)
2Hold  for more than 1 sec.
•Each time you press for over 1 sec.
the RF channel changes as shown
below.
For U.S., Canada, etc.
12345678
For Europe, Australia, Oceania and Asia1234
Registering the GyroRemote
in the Projector
When using one GyroRemote with multiple
projectors or one projector with multiple
GyroRemotes, the GyroRemote(s) should be
stored in the projector.
1Select “Register R/C” in the
Option (1) menu.
2On the “Do you want to enter the
Learn MOde?” (If the Gyro is
connected to projector by cable,
temporarily unplug the cable
from the projector and  press
ENTER button.) message,
select “Ye s” using 
 or , and
press 
.
RF CH : 3
LED
indicator
RF CH+ button
Adjustment button
(
"'\ | "'\ |"'\ | "'\ |
"'\ |)
ENTER button
-42
PG-M25X#E#p33_49.p6502.4.29, 3:12 PM 42 
						

							Basic Operation
-43
3Press  on the GyroRemote
you want to register.
•The LED indicator on the GyroRemote
lights up.
•“Register” is displayed at the bottom
of the screen for a few seconds and
registration starts.
When storing is complete, “Learn
Mode” is displayed.
Note
•If no action is taken for more than 5
minutes, the projector exits from the
Learn mode.
4Press 
•This completes the Registration mode.
Registering Multiple
GyroRemotes in One
Projector
A maximum of 8 GyroRemotes for U.S.,
Canada, etc. and 4 for Europe, Australia,
Oceania and Asia can be registered.
1Set the same channel for the
RF channel of the GyroRemote
you want to register.
2Using step 2 in page 42, press
 on the GyroRemotes to
be used.
•When registering other GyroRemotes
continuously, after each GyroRemote
is registered and the Registration
mode message is displayed, proceed
with the next GyroRemote.
•After 8 GyroRemotes for U.S., Canada
and 4 for Europe, Australia, Oceania
and Asia have been registered, the
Registration mode will automatically
terminate.
3Press  when the number of
registered GyroRemotes is
fewer than 8 for U.S., Canada
and 4 for Europe, Australia,
Oceania and Asia.
•This ends the Registration mode.
TEACH buttonLED
indicator
Register
TEACH buttonENTER button
PG-M25X#E#p33_49.p6502.4.29, 3:13 PM 43 
						

							Using the Presentation Tools
The GyroRemote is equipped with the following presentation tools. These are very useful
when emphasizing a main point during the presentation.
•Pointer function
•Stamp function
•Line function
Using the Pointer
Using the GyroRemote. For details see
page 40.
1Hold the GyroRemote and
move it while pressing 
.
•The pointer moves in accordance with
the GyroRemote’s movements.
•The pointer disappears when 
 is
released.
Note
•When operating the GyroRemote
with multiple projectors, the position
of the pointer may be slightly off in
each projector. This does not
indicate a malfunction.
Function 1 button
ENTER button
Function 3 button
Function 4 button
GYRO ACTIVE
buttonASSIGN buttonUNDO buttonPOINTER buttonFunction 2
button LED lamp
-44
PG-M25X#E#p33_49.p6502.4.29, 3:13 PM 44 
						

							Basic Operation
-45
Using the Stamp Func-
tion
Using the GyroRemote
For details see page 40.
1Press  on the GyroRemote
and then select “Button Assign
1/5”.
•The assign function is displayed at the
bottom right of the screen.
2Press  on the GyroRemote.
•The stamp type will change every time
 is pressed, as shown on the right.
3Press  on the GyroRemote to
select the color.
•The stamp color will change every time
 is pressed, as shown on the right.
4Move the GyroRemote while
holding down 
.
•The stamp will move on the screen.
5Release  at the location
on the screen that you want to
stamp, and press 
.
•The stamp will be fixed at that location.
Note
•If you want to display another stamp, re-
peat steps 2 to 4.
•Press 
 to clear a stamp.
•Even if the GyroRemote is moved, 
will not function if it is not held down.
Red Green Blue Yellow
Black White Purple Light blue
PG-M25X#E#p33_49.p6502.4.29, 3:13 PM 45 
						

							Using the Line Function
Using the GyroRemote, you can draw on the
screen various shapes such as squares, ovals,
horizontal, vertical, perpendicular and free-
style lines.
Using the GyroRemote,
For details see page 40.
1Presson the GyroRemote and
then select “Button Assign 1/5”.
•The assign function is displayed at the
bottom right of the screen.
2Press  on the GyroRemote.
•The type of drawing will change every time
 is pressed, as shown on the right.
3Press  on the GyroRemote to
select the color.
•The Line color will change every time is pressed, as shown on the right.
4Move the cursor to the starting
position while holding down
 on the GyroRemote.
Note
•If you want to display another stamp,
repeat steps 2 to 4.
•Press 
 to delete a stamp just
inserted.
•Press 
 to clear all stamps.
5Release  on the Gyro-
Remote and press 
.
6Move the cursor to the ending
position while holding down
 on the GyroRemote, and
press 
.
Note
•If you want to draw another shape
or line, repeat steps 1 to 5.
•Press 
 to clear any shapes or
lines you have just drawn in.
•Press 
 to clear all shapes or lines
you have drawn in.
Diagonal
lineHorizontal
or vertical
lineBox Circle Free line
11
1
22
2 2
2 1
1
:2:
:
How to drow lines and shapes
Red Green Blue Yellow
Black White Purple Light blue
Using the Presentation Tools (cont.)
Starting point Ending point Drawing direction
-46
PG-M25X#E#p33_49.p6502.4.29, 3:13 PM 46