Sharp Projector Pg Ls2000 User Manual

							
9
IntroductionCaution regarding usage of the projector
If you are not to use the projector for a long 
time or before moving the projector, make 
certain you unplug the power cord from the 
wall outlet, and disconnect any other 
cables connected to it.
Do not carry the projector by holding the 
lens.
Do not expose the projector to direct 
sunlight or place next to heat sources. 
Doing so may affect the cabinet color or 
cause deformation of the plastic cover.
Other connected equipment
When connecting a computer or other 
audio-visual equipment to the projector, 
make the connections AFTER unplugging 
the power cord of the projector from the 
AC outlet and turning off the equipment to 
be connected.
Please read the operation manuals of the 
projector and the equipment to be 
connected for instructions on how to make 
the connections.
Using the projector in other countries
The power supply voltage and the shape of 
the plug may vary depending on the region 
or country you are using the projector in. 
When using the projector overseas, make 
sure you use an appropriate power cord for 
the country you are in.
■
■
■
■
■
■
Temperature monitor function
If the temperature inside the projector 
increases, due to blockage of the air vents, 
or the setting location, the temperature 
warning indicator will blink. And if the 
temperature keeps on rising, “
” will 
illuminate in the lower left corner of the 
picture with the temperature warning 
indicator blinking. If this state continues, 
the lamp will turn off, the cooling fan will 
run and then the projector will enter 
Standby mode. Refer to “Maintenance 
Indicators” on pages 
54 and 55 for details.
Info
The cooling fan regulates the internal 
temperature, and its performance is automatically 
controlled. The sound of the fan may change 
during projector operation due to changes in the 
fan speed. This does not indicate malfunction.
■
•
Closed Caption uses Bitstream Vera fontsCopyright (c) 2003 by Bitstream, Inc. All Rights Reserved. Bitstream Vera is a trademark of Bitstream, Inc.
Permission is hereby granted, free of charge, to any person obtaining a copy of the fonts accompanying this 
license (“Fonts”) and associated documentation fi  les (the “Font Software”), to reproduce and distribute the 
Font Software, including without limitation the rights to use, copy, merge, publish, distribute, and/or sell 
copies of the Font Software, and to permit persons to whom the Font Software is furnished to do so, subject 
to the following conditions:
The above copyright and trademark notices and this permission notice shall be included in all copies of one 
or more of the Font Software typefaces.
The Font Software may be modifi ed, altered, or added to, and in particular the designs of glyphs or 
characters in the Fonts may be modifi ed and additional glyphs or characters may be added to the Fonts, 
only if the fonts are renamed to names not containing either the words “Bitstream” or the word “Vera”.
This License becomes null and void to the extent applicable to Fonts or Font Software that has been 
modifi  ed and is distributed under the “Bitstream Vera” names.
The Font Software may be sold as part of a larger software package but no copy of one or more of the Font 
Software typefaces may be sold by itself.
THE FONT SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANT Y OF ANY KIND, EXPRESS OR 
IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTIES OF MERCHANTABILIT Y, FITNESS FOR A 
PARTICULAR PURPOSE AND NONINFRINGEMENT OF COPYRIGHT, PATENT, TRADEMARK, OR OTHER 
RIGHT. IN NO EVENT SHALL BITSTREAM OR THE GNOME FOUNDATION BE LIABLE FOR ANY CL AIM, 
DAMAGES OR OTHER LIABILIT Y, INCLUDING ANY GENERAL, SPECIAL, INDIRECT, INCIDENTAL, OR 
CONSEQUENTIAL DAMAGES, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING 
FROM, OUT OF THE USE OR INABILIT Y TO USE THE FONT SOFT WARE OR FROM OTHER DEALINGS IN 
THE FONT SOFTWARE.
Except as contained in this notice, the names of Gnome, the Gnome Foundation, and Bitstream Inc., shall 
not be used in advertising or otherwise to promote the sale, use or other dealings in this Font Software 
without prior written authorization from the Gnome Foundation or Bitstream Inc., respectively. For further 
information, contact: fonts at gnome dot org. 
						

							
10
Part Names and Functions
Numbers in Z refer to the main pages in this operation manual where the 
topic is explained.
13
11
12
1
2
5
6
3
4
7
9
8
1014
15 1617
Front View
  1  Temperature warning indicator 54
  2   Lamp indicator 54
  3   Power indicator 54
  4  STANDBY/ON button 23    For turning the power on and putting the  
projector into Standby mode.
  5  ENTER button 35   For setting items selected or adjusted on 
the menu.
  6  VOL ( Volume) buttons  (–O /Q +) 27    For adjusting the speaker sound level.
  7  AUTO SYNC button 31    For automatically adjusting images when 
connected to a computer.
  8  Adjustment buttons  (P /R /O /Q )35    For selecting menu items.
  9  INPUT buttons  (P /R )27    For switching Input mode.
10  MENU button 35    For displaying adjustment and setting 
screens.
To p  V i e w
11   Zoom ring 25    For enlarging/reducing the picture.
12 Focus ring 24    For adjusting the focus.
13   Intake vent 53
14   Security bar
15    HEIGHT ADJUST lever 25
16   Adjustment foot 25
17    Remote control sensor 13 
						

							
11
Introduction
12345
8
9
10 6
7
Rear View (Terminals)
  1 HDMI terminal
 (PG-LX2000 only) 19, 20, 21
Terminal for HDMI input.
  2   AUDIO input terminal 21
  3   VIDEO input terminal 20  Terminal for connecting video equipment.
4  COMPUTER/COMPONENT input  terminal 19, 20Terminal for computer RGB and 
component signals.
  5 RS-232C terminal 22  Terminal for controlling the projector using  a computer.
  6   Exhaust vent 53
  7   Speaker 46
8   Kensington Security Standard connector
  9   Rear adjustment foot 25
10  AC socket 21Connect the supplied power cord. Using the Kensington Lock
This projector has a Kensington Security 
Standard connector for use with a 
Kensington MicroSaver Security System. 
Refer to the information that came with the 
system for instructions on how to use it to 
secure the projector.
• 
						

							
12
Part Names and Functions (Continued)
Numbers in Z refer to the main pages in this operation manual where the 
topic is explained.
2
3
4
8
10
11
6 1
7
9
12
13
14
16
18
20
21
22
19 17
515
Adjustment buttons ( P/R /O /Q )35For selecting and adjusting menu items.9
ON button 23For turning the power on.1
STANDBY button 23For putting the projector into the Standby 
mode.2
BREAK TIMER button 30For displaying the break time.5
MAGNIFY buttons 31For enlarging/reducing part of the image.3
POINTER button 30For displaying the pointer.8
INPUT buttons  (P /R )27For switching Input mode.14
EFFECT button 30For changing the pointer or spot area.10
KEYSTONE button 26For entering the Keystone Correction 
mode.11
AUTO SYNC button 31, 46For automatically adjusting images when 
connected to a computer.16
FUNCTION button 49For operating and executing a function 
assigned to “FUNCTION Button”.12
ECO+QUIE T but ton 30For lowering the noise of the cooling fan 
and extending the lamp life.21
FREEZE button 31For freezing images.4
AV MUTE button 27For temporarily displaying a black screen 
and turning off the sound.6
VOL +/– ( Volume) buttons 27For adjusting the speaker sound level.13
SPOT button 30For displaying the spotlight.7
ENTER button 35For setting items selected or adjusted on 
the menu.19
RETURN button35For returning to the previous menu screen 
during menu operations.20
MENU button 35For displaying adjustment and setting 
screens.18
RESIZE button 28For switching the picture size (NORMAL, 
16:9, e tc.).17
3D MODE button 52
For displaying the 3D MODE menu screen.
22
PICTURE MODE button 31For selecting the appropriate picture.15 
						

							
13
IntroductionInserting the Batteries
1  Pull down the tab on the cover and remove the cover towards the direction of the arrow.
2  Insert the batteries.Insert the batteries making sure the polarities correctly match 
the  m and  n marks inside the battery compartment.
3  Insert the lower tab of the cover into the opening, 
and lower the cover until it clicks in place.
Incorrect use of the batteries may cause them to leak or explode. 
Please follow the precautions below
Caution
Danger of explosion if battery is incorrectly replaced.
Replace only with alkaline or manganese batteries.
Insert the batteries making sure the polarities correctly match the  m and  n marks inside the batter y 
compartment.
Batteries of different types have different properties, therefore do not mix batteries of different types.
Do not mix new and old batteries. 
This may shorten the life of new batteries or may cause old batteries to leak.Remove the batteries from the remote control once they have run out, as leaving them in can cause them to leak.Battery fl uid from leaked batteries is harmful to skin, therefore ensure you wipe them fi rst and then 
remove them using a cloth.
The batteries included with this projector may run down in a short period, depending on how they are kept. 
Be sure to replace them as soon as possible with new batteries.
Remove the batteries from the remote control if you will not be using the remote control for a long time.
Comply with the rules (ordinance) of each local government when disposing of worn-out batteries.
•
•
•
•
•
•
•
•
•
1
2
3
Usable Range
The remote control can be used to control the 
projector within the ranges shown in the 
illustration.
The signal from the remote control can be 
refl ected off a screen for easy operation. 
However, the effective distance of the signal 
may differ depending on the screen material.
•
Note
When using the remote controlEnsure that you do not drop it or expose it to 
moisture or high temperature.
The remote control may malfunction under a 
fl uorescent lamp. In this case, move the 
projector away from the fl uorescent lamp.
•
•
Remote control sensor
Remote control signal 
transmitters
Remote control 33
n (10 m)
30°
30°Remote control sensor
Remote control signal 
transmitters
Remote control 33
n (10 m)
30°
30° 
						

							
14
Easy Start
This section shows the basic operation (projector connecting with the computer). For details, 
see the page described below for each step.
Setup and Projection
In this section, connection of the projector and the computer is explained using one example.
STANDBY button8
KEYSTONE button5 3
ON button
6INPUT buttons
5Adjustment 
buttons 
(P /R /O /Q )
O /Q  buttons6
STANDBY/ON 
button3
8
Focus ring4
HEIGHT 
ADJUST lever4
Zoom ring4
INPUT buttons6
6
1. Place the projector facing a wall or a screen       BP.  1 6
When connecting equipment other than a computer, see pages 20 and 21.
2. Connect the projector to the computer and plug the power 
cord into the AC socket of the projector
B PP. 19, 21
Press  STANDBY/ON  on the projector or  ON on the remote control.
3. Turn the projector on
BP.  2 3 
						

							
15
Easy Start
1  After the projector turns on, the Setup Guide appears.
  (When “Setup Guide” is set to “On”. See page 
45.)
2Follow the steps in the Setup Guide and adjust the focus, height (angle) and picture size.
3  After adjusting the focus, height (angle) and picture size, press  ENTER to fi nish the 
Setup Guide.
4.  Adjust the projected image with the Setup Guide
B P.  2 4
Correcting trapezoidal distortion using Keystone Correction.
On the remote control Shrinks 
upper side. Shrinks 
lower side.
5. Correct trapezoidal distortion
B P.  2 6
Press  INPUT P/R  to display the INPUT list. Use  INPUTP/R  to select the Input mode.
On the 
projector On the remote 
control
INPUT list (e.g. PG-L X2000)
AudioINPUT
H
V
COMPUTER
HDMI
VIDEO
[PG-LX2000 only]
When you select HDMI input, use  O/Q  to select the audio input terminal (HDMI or AUDIO).
6. Select the Input mode
B P.  2 7
7. Turn the computer on
Press  STANDBY/ON  on the projector or  STANDBY on the remote control, and then press 
the button again while the confi rmation message is displayed to put the projector into 
Standby mode.
On-screen display
On the 
projector On the remote 
control
8. Turn the power off
BP.  2 3 
						

							
16
Setting Up the Projector
Video Setup
If using this projector outside the U.S.A., please change setting to “0 IRE” in Video Setup. (See 
page 42.)
Setting Up the Projector
For optimal image quality, position the projector perpendicular to the screen with the projector's 
feet fl at and level. Doing so will eliminate the need for Keystone correction and provide the best 
image quality. (See page 
26.)
Standard Setup (Front Projection)
Place the projector at the required distance from the screen according to the desired picture 
size. (See page 17.)
Indication of the Projection Image Size and Projection Distance
Example: 4:3 Signal Input (Normal Mode)
300" (762 cm)
200" (508 cm)
100" (254 cm)
40" (102 cm)
5'2"–6'2"
(1.6 m – 1.9 m) 12'11"–15'6"
(3.9 m – 4.7 m)
25'10"–30'11"
(7.9 m – 9.4 m)38'9"–46'5"
(11.8 m – 14.2 m)
240" ×180"
(610 cm  ×457 cm)
160"×120"
(406 cm 
×305 cm)80"×60"(203 cm ×152 cm)32"×24"(81 cm ×61 cm)
Picture Size
Projection
Distance
■ 
						

							
17
Setup
Screen Size and Projection Distance
ScreenLens center
H L
4:3 Signal Input (Normal Mode)
Picture (Screen) size Projection distance [L]Distance from the lens center
to the bottom of the image [H]Diag. [ F
] Width Height Minimum [L1] Maximum [L2]300" (762 cm) 610 cm (240") 457 cm (180") 11.8 m (38' 9") 14.2 m (46' 5")17 cm
(6 23/32")250" (635 cm) 508 cm (200") 381 cm (150") 9.9 m (32' 4") 11.8 m (38' 8")14 cm
(519/32")200" (508 cm) 406 cm (160") 305 cm (120") 7.9 m(25' 10")9.4 m(30' 11")11 cm(4 31/64")150" (381 cm) 305 cm (120") 229 cm (90") 5.9 m (19' 5") 7.1 m (23' 3")9 cm(323/64")120" (305 cm) 244 cm (96") 183 cm (72") 4.7 m (15' 6") 5.7 m (18' 7")7 cm(211/16")100" (254 cm) 203 cm (80") 152 cm (60") 3.9 m(12' 11")4.7 m (15' 6")6 cm(215/64")80" (203 cm) 163 cm (64") 122 cm (48") 3.2 m (10' 4") 3.8 m (12' 5")5 cm
(1 51/64")70" (178 cm) 142 cm (56") 107 cm (42") 2.8 m (9' 1") 3.3 m(10' 10")4 cm(1 9/16")60" (152 cm) 122 cm (48") 91 cm (36") 2.4 m (7' 9") 2.8 m (9' 3")3 cm(1 11/32")40" (102 cm) 81 cm (32") 61 cm (24") 1.6 m (5' 2") 1.9 m (6' 2")2 cm(57/64")
16:9 Signal Input (16:9 Mode)
Picture (Screen) size Projection distance [L]Distance from the lens 
center to the bottom  of the image [H]Adjustable range of image position [S]
Diag. [ F
] Width Height Minimum [L1] Maximum [L2]
300" (762 cm) 664 cm (261") 374 cm (147") 12.9 m (42' 3") 15.4 m (50' 7") 81 cm(31 53/64")±62 cm(±24 33/64")
250" (635 cm) 553 cm (218") 311 cm (123") 10.7 m (35' 3") 12.8 m (42' 2") 67 cm(2617/32")±52 cm(±20 27/64")200" (508 cm) 443 cm (174") 249 cm (98") 8.6 m (28' 2") 10.3 m (33' 9") 54 cm(21 7/32")±42 cm(±16 11/32")150" (381 cm) 332 cm (131") 187 cm (74") 6.4 m (21' 2") 7.7 m (25' 3") 40 cm(15 59/64")±31 cm(±12 1/4")120" (305 cm) 266 cm (105") 149 cm (59") 5.2 m (16' 11") 6.2 m (20' 3") 32 cm(12 47/64")±25 cm(±9 13/16")100" (254 cm) 221 cm (87") 125 cm (49") 4.3 m (14' 1") 5.1 m (16' 10") 27 cm(10 39/64")±21 cm(±8 11/64")80" (203 cm) 177 cm (70") 100 cm (39") 3.4 m (11' 3") 4.1 m (13' 6") 22 cm(831/64")±17 cm(±6 17/32")60" (152 cm) 133 cm (52") 75 cm (29") 2.6 m (8' 5") 3.1 m (10' 1") 16 cm(6 23/64")±12 cm(±4 29/32")40" (102 cm) 89 cm (35") 50 cm (20") 1.7 m (5' 8") 2.1 m (6' 9") 11 cm(4 1/4")±8 cm(±3 17/64")
When using the projector with screen sizes not listed in the above charts, calculate the values according to the formulas.
4:3 Signal 16:9 Signal
[m/cm] [Feet/inches] [m/cm] [Feet/inches]
L1: Minimum projection distance (m/ft) 0.03941
F0.03941F / 0.3048 0.04294F0.04294F / 0.3048
L2: Maximum projection distance (m/ft) 0.04717F0.04717F / 0.3048 0.05139F0.05139F / 0.3048
H:
Distance from the lens center to the bottom of the image (cm/in)0.05689F0.05689F / 2.54 0.26952F0.26952F / 2.54
S:
Adjustable range of image position (cm/in)See page  43.— — ±0.20754F±0.20754F / 2.54
F
 : Picture diagonal size : 40-300
Allow a margin of error in the values in the 
diagrams below.
•
Note
Allow a margin of error in the values in the 
diagrams below.
•
Note 
						

							
18
Setting Up the Projector (Continued)
Projection (PRJ) Mode
The projector can use any of the 4 projection modes shown in the diagram below. Select the 
mode most appropriate for the projection setting in use.  ( You can set the PRJ mode in “SCR-
ADJ” menu. See page 
45.)
Table mounted, front projection
[Menu item➞ “Front”]
Table mounted, rear projection
(with a translucent screen)
[Menu item ➞ “Rear”]
■
■ Ceiling mounted, front projection
[Menu item
➞“Ceiling + Front”]
Ceiling mounted, rear projection
(with a translucent screen)
[Menu item ➞“Ceiling + Rear”]
■
■
a
Ceiling-Mount Setup
It is recommended that you use the optional Sharp ceiling-mount adaptor and unit for this 
installation. Before mounting the projector, contact your nearest Sharp Authorized Projector 
Dealer or Service Center to obtain the recommended ceiling-mount adaptor and unit (sold 
separately).