Sharp Projector Pg C355w User Manual

-9
Introduction
Caution regarding usage of the projector
■When using the projector, take care not to sub-
ject it to hard impact and/or vibration, as this
can result in damage. Take extra care with the
lens. If you are not to use the projector for a
long time, make certain you unplug the power
cord from the wall outlet, and disconnect any
other cables connected to it.
■Do not carry the projector by holding the lens.
■
When storing the projector, ensure you attach
the lens cap to the projector. (See page...

-10
Accessories
Remote control
Two R-6 batteries
(“AA” size, UM/SUM-3,
HP-7 or similar)
Power cord
*
For U.S., Canada, etc.
(6 (1.8 m))
For Europe, except U.K.
(6 (1.8 m))

*Use the power cord that corresponds to the wall outlet in your country.
■Lamp unit AN-C430LP
■Ceiling-mount adaptor AN-60KT
AN-XGCM55 (for U.S.A. only)
■Universal bracket AN-JT200 (for U.S.A. only)
■Ceiling-mount unit AN-TK201 
AN-TK202 
AN-EP101B 
(for U.S.A. only)
■Remote receiver AN-MR2
■3 RCA to 15-pin D-sub cable (10 (3.0 m))...

-11
Introduction
Optional lenses
■Lens Projection distance for 100 screen size
Wide-zoom lens ( × 1.5 – 1.9) AN-C12MZ 10 5 – 13 1 (3.2 m – 4.0 m)
T ele-zoom lens ( × 2.2 – 2.8) AN-C18MZ 15 7 – 19 10 (4.8 m – 6.0 m)
T ele-zoom lens ( × 3.3 – 5.1) AN-C27MZ 23 2 – 35 8 (7.1 m – 10.9 m)
T ele-zoom lens ( × 5.1 – 7.2) AN-C41MZ 36 2 – 50 10 (11.0 m – 15.5 m)
The standard zoom lens is attached to the projector.
The optional lenses from Sharp are also available for specialized applic\
ation. Please see
your...

-12
43MENU buttonFor displaying adjustment 
and setting screens.
44
35AUTO SYNC buttonFor automatically adjusting 
images when connected to 
a computer.
ENTER buttonFor setting items selected 
or adjusted on the menu.
32KEYSTONE buttonFor entering the Keystone 
Correction mode.
30STANDBY/ON buttonFor turning the power on and 
putting the projector into 
standby mode.
15Remote control
sensor
43Adjustment buttons 
('/"/\/|)
For selecting and adjusting 
on-screen items.
51Speaker
33Focus ringFor...

-13
Introduction
Projector (Rear View)
* Using the Kensington Lock
•This projector has a Kensington Security Standard connector for use with a Kensington MicroSaver Security
System. Refer to the information that came with the system for instructions on how to use it to secure the
projector.
56Intake ventCarrying handle
15Remote control 
sensor
56Exhaust vent
30AC socketConnect the supplied  power cord.* Kensington Security 
Standard connector
LAN terminalTerminal for controlling the 
projector using a...

-14
Remote Control
30STANDBY buttonFor putting the projector into  
standby mode.
32KEYSTONE buttonFor entering the Keystone 
Correction mode.
35FREEZE buttonFor freezing images.
36MAGNIFY (Enlarge/Reduce) 
buttons
For enlarging/reducing part of the 
image.
44
39
ENTER buttonFor setting items selected or 
adjusted on the menu.
35BREAK TIMER  buttonFor displaying the break timer.
34INPUT buttonsFor switching to the respective 
input modes.
35AUTO SYNC buttonFor automatically adjusting images 
when...

-15
IntroductionUsing the Remote Control
Inserting the Batteries
1Pull down the tab on the cover and
remove the cover towards the di-
rection of the arrow.
2Insert the included batteries.
•Insert the batteries making sure the po-
larities correctly match the 
 and 
marks inside the battery compartment.
3Insert the lower tab of the cover
into the opening, and lower the
cover until it clicks in place.
Incorrect use of the batteries may cause them to leak or explode. Please follow the precautions below....

-16
Quick Start
7  STANDBY
button
3  ON button
6  COMPUTER 1
    button 37  STANDBY/ON button
6  INPUT buttons
6  ENTER button
4  Height Adjustment buttons
5  Zoom knob
5  Focus ring
4  Tilt dial
Page 18
1.Place the projector facing a screen
Pages 23, 30
Page 30
On the remote control On the projector This section shows the basic operation (projector connecting with the computer). For details, see the page
described below for each step.
Setup and Projection
In this section, connection of the projector and...

-17
Quick Start
Pages 31, 32
4.Adjust the angle
5.Adjust the focus and the zoom
7.Turn the Power off
Page 30
6.Select the INPUT mode
Page 34
•
• •
•
•This projector is equipped with an “Auto V-Keystone
Correction” function that automatically corrects any
trapezoidal distortion within the projected image.
Bring the projected image into focus
•
• •
•
• Bring the projected image into focus by
rotating the focus ring. Adjust the projected image size
•
• •
•
• Adjust the projected image  size by moving the...

-18
Setting Up the Projector
For optimal image quality, position the projector perpendicular to the screen with the projector’s feet flat
and level. Doing so will eliminate the need for Keystone correction and provide the best image quality. (See
page 32.)
Standard Setup (Front Projection)
■Place the projector at the required distance from the screen according
to the desired picture size. (For details, refer to the “SETUP MANUAL” con-
tained on the supplied CD-ROM.)
Example of standard setup
Setting Up...