Sharp Projector Dt 200 User Manual

							E-30
Basic Operation
Adjusting the Picture
Adjusting the Color Temperature
This function allows for selecting the desired color
temperature from six settings. With the lower value
selected, the projected image becomes warmer,
reddish and incandescent-like while with the higher
value, the image becomes cooler, bluish and
fluorescent-like.
Description of Color Temperature
1Press MENU. The “Picture” menu screen appears.
2Press 
/ to select “CLR Temp”, and then press
.
3Press 
/ to select the desired color
temperature setting.
4Press ENTER to save the setting.
5To exit the menu screen, press MENU.
•Values on “CLR Temp” are only for general standard
purposes. The less the value is set to, the warmer, reddish,
incandescent-like the image becomes. The more the value
is set to, the cooler, bluish, fluorescent-like the image
becomes.
•“CLR-Temp” cannot be used in the DIGITAL INPUT mode.
On-screen Display
2, 3 41, 5
Emphasizing the Contrast
This function emphasizes the bright por tions of images
to obtain a higher contrast image.
Description of White Emphasis
1Press MENU. The “Picture” menu screen appears.
2Press 
/ to select “White Emphasis”.
3Press 
/ to select the desired white emphasis
setting.
4To exit the menu screen, press MENU. On-screen Display
1, 42, 3
Description Selected item
For emphasizing the bright portions of images
For disabling “White Emphasis”ON ()
OFF (
)
DT-200(E)#p26_32.p6502.11.21, 11:38 AM 30 
						

							E-31
Basic Operation
Gamma Correction Function
Gamma is an image quality enhancement function.
Four gamma settings are available to allow for
differences in the brightness of the room.
Description of Gamma Modes
Description Selected Mode
Standard
Black Detail
White Detail
BrightenStandard picture without gamma correction
Gives greater depth to darker portions of
images for a more exciting theater experience.
Emphasizes the gradation of the intermediate
to high brightness portions of the image for
more detailed expression.
Brighten the darker portions of images for
easier viewing in a dimly lit room.
1Press MENU. The “Picture” menu screen appears.
2Press 
/ to select “Gamma”, and then press
.
3Press 
/ to select the desired gamma mode.
4Press ENTER to save the setting.
5To exit the menu screen, press MENU.
•Gamma cannot be used in the DIGITAL INPUT mode.
On-screen Display
Standard Black Detail
White Detail Brighten
2, 3 41, 5
Adjusting the Picture
DT-200(E)#p26_32.p6502.11.21, 11:38 AM 31 
						

							E-32
Basic Operation
Picture Setting Function
This function stores all items set in “Picture”. Five
settings can be stored separately in “Memory 1” to
“Memory 5”. Each stored setting is reassigned to each
input mode (INPUT 1 to INPUT 4 and DIGITAL).
Even when the input mode or signal is changed, you
can easily select optimal settings from the stored
settings.
•This function can be operated using the PICTURE SETTING
button on the projector or on the remote control, as well as
the OSD menu screen.
Description of Picture Setting
Memory 1-5Settings of all items in “Picture” can be stored for
the respective input modes. The stored settings
can be selected in any input modes.
MemoryBesides “Memory 1” to “Memory 5”, other settings
OFFcan be stored for each input mode. “Memory OFF”
can be selected for each input mode.
Selecting “Memory 1-5” or “Memory
OFF” Using the PICTURE SETTING
Button
1Press PICTURE SETTING, Each time PICTURE
SETTING is pressed, the memory number
changes as shown below.
Memory 1 Memory 2 Memory 3
Memory OFF Memory 5 Memory 4
Storing the Adjustment Values for
each Memory Number
1Press MENU. The “Picture” menu screen
appears.
2Press 
/ to select “Picture Setting”, and then
press 
.
3Press 
/ to select the desired memory number
for the picture settings.
4Press ENTER to save the settings. Adjust the
settings described on pages 29 to 31. The values
that are adjusted are stored.
5To exit the menu screen, press MENU. On-screen Display
1
Selected item Description
Adjusting the Picture
2, 3 41, 5
DT-200(E)#p26_32.p6502.11.21, 11:38 AM 32 
						

							E-33
Basic Operation
When displaying computer patterns which are very
detailed (tiling, vertical stripes, etc.), interference may
occur between the DMD pixels, causing flickering,
vertical stripes, or contrast irregularities in portions of
the screen. Should this occur, adjust “Clock”, “Phase”,
“H-Pos” and “V-Pos” for the optimum computer image.
• “Clock”, “Phase”, “H-Pos” and “V-Pos” cannot be used in the
DIGITAL INPUT mode and the Component mode.
• Computer image adjustments can be made easily by pressing
AUTO SYNC (
) on the remote control. See page 35 for details.
1Press MENU. The “Picture” menu screen appears.
2Press 
/ to display the “Fine Sync” menu
screen.
3Press  
/  to select a specific adjustment item.
4Press 
/ to move the  mark of the selected
adjustment item to the desired setting.
5To exit the menu screen, press MENU.
• To reset all adjustment items, select “Reset” on the “Fine Sync”
menu screen and press ENTER.
• The adjustable area of each item may be changed according to
the input signal.
On-screen Display
Adjusts vertical noise.
Adjusts horizontal noise (similar to tracking on your VCR).
Centers the on-screen image by moving it to the left or right.
Centers the on-screen image by moving it up or down.
All computer image adjustment items are returned to the factory
preset settings.Clock
Phase
H-Pos
V-Pos
Reset
Description of Adjustment Items
2
Description Selected item
Adjusting the Computer and DVD/DTV Images
3
2,3,4
1, 5
DT-200(E)#p33.p6502.11.21, 11:44 AM 33   
						

							E-34
Basic Operation
Adjusting the Computer and DVD/DTV Images
Special Modes Adjustment
Ordinarily, the type of input signal is detected and the
correct resolution mode is automatically selected.
However, for some signals, the optimal resolution mode
in “Special Modes” on the “Fine Sync” menu screen
may need to be selected to match the computer display
mode.
1Press MENU. The “Picture” menu screen appears.
2Press 
/ to display the “Fine Sync” menu
screen.
3Press 
/ to select “Special Modes”, and then
press 
.
4Press 
/ to select the optimal resolution.
5Press ENTER to save the setting.
6To exit the menu screen, press MENU.
• Avoid displaying computer patter ns which repeat every other line
(horizontal stripes). (Flickering may occur, making the image hard
to see.)
• When inputting DTV 1080i signal, select the corresponding type of
signal in step 4 above.
• When inputting 720P RGB signal, select the corresponding type
of signal in step 4 above.
• “Special modes” cannot be used in the DIGITAL INPUT mode.
On-screen Display
On-screen Display
Checking the Input Signal
This function allows you to check the current input signal
information.
1Press MENU.  The “Picture” menu screen appears.
2Press 
/ to display the “Fine Sync” menu
screen.
3Press 
/ to select “Signal Info” to display the
current input signal.
4To exit the menu screen, press MENU.
2,3,41, 6
5
2,31, 4
DT-200(E)#p34_35.p6502.11.21, 11:43 AM 34 
						

							E-35
Basic Operation
Adjusting the Computer and DVD/DTV Images
Auto Sync Adjustment
•Used to automatically adjust a computer image.
•Select whether the image is to be synchronized
automatically when switching the signal with “ON” or
“OFF”.
OFF (
)
•Synchronized adjustment is not automatically
performed.
•Press AUTO SYNC to perform manual adjustment.
ON (
)
•Synchronized adjustment is automatically performed.
1Press MENU. The “Picture” menu screen appears.
2Press 
/ to display the “Fine Sync” menu
screen.
3Press 
/ to select “Auto Sync”.
4Press 
/ to select “ON” or “OFF”.
5To exit the menu screen, press MENU.
•When the optimum image cannot be achieved with Auto
Sync adjustment, use manual adjustments. (See page 33.)
•The Auto Sync adjustment may take some time to complete,
depending on the image of the computer connected to the
projector.
•“Auto Sync” cannot be used in the DIGITAL INPUT mode.
On-screen Display
2,3,41, 5
AUTO SYNC
button
Auto Sync Adjustment Using the
Remote Control
1Press AUTO SYNC button on the Remote Control.
Synchronized adjustment starts.
FREEZE
AUTO SYNC
button
DT-200(E)#p34_35.p6502.11.21, 11:43 AM 35 
						

							E-36
Basic Operation
Turning On/Off the On-screen Display
This function allows you to turn on or off the on-screen
messages that appear during input select.
1Press MENU. The “Picture” menu screen appears.
2Press 
/ to display the “Options” menu screen.
3Press 
/ to select “OSD Display”.
4Press 
/ to select “ON” () or “OFF” ().
5To exit the menu screen, press MENU.On-screen Display
Description Selected item
ON (
)
OFF (
)
Description of OSD Display
All On-screen Display are displayed.
INPUT is not displayed.2,3,41, 5
2,3,41, 5
On-screen DisplayThis function allows you to select the input signal type
Component or RGB for INPUT 2.
1Press MENU. The “Picture” menu screen appears.
2Press 
/ to display the “Options” menu screen.
3Press 
/ to select “Signal Type”, and then
press 
.
4Press 
/ to select “RGB” or “Component”.
5To exit the menu screen, press MENU.
“RGB” or “Component” can be selected with the
RGB/COMP. button on the remote control only in
INPUT 2.
Selecting the Signal Type
RGB/COMP.  button
DT-200(E)#p36_40.p6502.11.21, 11:42 AM 36 
						

							E-37
Basic Operation
Selecting a Background Image
On-screen DisplayThis function allows you to select the image displayed
when no signal is being sent to the projector.
Description of Background Images
1Press MENU. The “Picture” menu screen appears.
2Press 
/ to display the “Options” menu screen.
3Press 
/ to select “Background”.
4Press 
/ to select the background image you
want to display on the screen.
5To exit the menu screen, press MENU.
Selected item
Blue (
)
None (
)Description
Blue screen
Black screen2,3,41, 5
Setting the Video Signal (VIDEO menu only)
The video input system mode is preset to “Auto”;
however, it can be changed to a specific system mode
if the selected system mode is not compatible with the
connected audiovisual equipment.
1Press MENU. The “Picture” menu screen appears.
2Press 
/ to display the “Options” menu screen.
3Press 
/ to select “Video Systems”, and then
press 
.
4Press 
/ to select the desired video system
mode.
5Press ENTER to save the setting.
6To exit the menu screen, press MENU.
•When the system mode is set to “Auto”, you may not receive
a clear picture due to signal differences. Should this occur,
switch to the video system of the source signal.
•“Auto” cannot be set for PAL-M and PAL-N input signals.
Select “PAL-M” or “PAL-N” in “Video Systems” menu for
PAL-M and PAL-N input signals.
2,3,41, 6
5
On-screen Display
DT-200(E)#p36_40.p6502.11.21, 11:42 AM 37 
						

							E-38
Basic Operation
Adjustments for the Screen Position and Size
On-screen DisplayYou can adjust settings according to the position and
size of the screen.
Description of Adjustment Items
Digital Shift Setting
This function allows you to adjust the vertical position
of the image.
Description of Digital Shift
1Press MENU. The “Picture” menu screen appears.
2Press 
/ to display the “Options” menu screen.
3Press 
/ to select “Digital Shift”.
4Press 
/ to move the  mark of the Digital Shift
setting.
5To exit the menu screen, press MENU.
•The “Digital Shift” cannot be adjusted when Keystone
correction is applied.
2,3,41, 5
Digital Shift
Subtitle
ResetAdjusts the vertical position of the image.
Adjusts the vertical size of the image.
Digital Shift and Subtitle adjustments are
returned to the factory preset settings.
Description Selected item
The image moves down.The image moves up.
 button button
DT-200(E)#p36_40.p6502.11.21, 11:42 AM 38 
						

							E-39
Basic Operation
1Press MENU. The “Picture” menu screen appears.
2Press 
/ to display the “Options” menu screen.
3Press 
/ to select “Subtitle”.
4Press 
/ to move the  mark of the Subtitle
setting.
5To exit the menu screen, press MENU.
•When changing the screen with the Subtitle setting, not only
the bottom of the screen rises, but also the upper part is
changed to a certain point.
•The subtitle setting can be adjusted more effectively with
the Digital Shift function.
•The “Subtitle” cannot be adjusted when Keystone correction
is applied.
Adjustments for the Screen Position and Size
On-screen Display
2,3,41, 5
Subtitle Setting
With this function, you can adjust the vertical size of the
display to allow for subtitles.
Description of Subtitle Setting
The image is enlarged by
adjusting the ver tical size of the
display.The image is compressed by
adjusting the vertical size of the
display.
 button button
DT-200(E)#p36_40.p6502.11.21, 11:42 AM 39