Sharp Pn V601 Operation Guide

E11
Menu Items
AUDIO LEVEL(STEREO MINI)
Selects the maximum audio input level of the audio input 
terminal.
SELF ADJUST
On a PC D-SUB/PC RGB screen, specify whether to 
perform screen adjustment automatically or not. When ON 
is selected, the screen is automatically adjusted when its 
resolution is 800 x 600 or higher and the timing of input 
signals changes. “ADJUSTING” appears on the screen 
during the adjustment. For images with black edges, etc., 
depending on the signal, adjustment may not be...

E12
Menu Items
n MULTI
ENLARGE (See page 13.)
Sets whether or not to use the enlarge function.
ADVANCED (ENLARGE)
ENLARGE H / ENLARGE V
 .........   Sets the number of screen splits (number of 
monitors) in the horizontal/vertical direction used for 
the enlargement.
ENLARGE-POS  .........   Specify the split screen to be displayed when the 
enlargement function is used.
H-POS / V-POS  .........   Adjust the horizontal/vertical position of the enlarged 
screen.
BEZEL ADJUST
Sets whether or not to use the...

E13
Menu Items
n Enlarge
• 
You can align several monitors and integrate them into a 
single large screen to display.
•  Up to five monitors can be aligned in both the horizontal 
and vertical directions.
•  Each monitor displays enlarged views of separated images.
(Example)
Horizontal direction: 2 monitor s
Ve rtical direction: 2 monitor s
Horizontal direction: 3 monitor s
Ve rtical direction: 2 monitor s
Setting procedure
Set using the MULTI menu.
1.  Set ENLARGE to ON.
2.   Select ADVANCED (ENLARGE)....

E14
nSCHEDULE
You can set the time to switch the monitor on and off.
Set this function with “SCHEDULE” in the OPTION menu. (See 
page 11.)
SCHEDULE
 
No.  POWER  DAY OF  THE WEEK TIME INPUT 
XXXX/XX/XX XXX  XX:XX:XX 
(2) 
OK…
[MENU] 
1366x768 V: 60 Hz    H: 47.7 kHz
(1)  (3) 
(4)  (5)
PC D-SUB
1.  Press  or  to select the SCHEDULE number, and 
press 
.
2.   Set the SCHEDULE. (See the description below.)
Press 
 or  to select items, and press  or  to 
change the setting.
3.   Press 
MENU.
SCHEDULE becomes...

E15
nADVANCED items (AV input) (See page 9 
for additional Menu item details.)
FLESH TONE
Adjust the hue control.
3D-NR
Reduce the noise of playback images on video.
Setting a higher level reduces more noise. However, it may 
cause blurring on an image.
MPEG-NR
Reduce block noise caused by digital compression.
3D-Y/C (AV VIDEO)
Specify whether to perform 3-dimension Y/C separation.
If dot interference or cross-color is occurring in fast-motion 
scenes, selecting “OFF” may improve the image quality....

16E
You can return the settings to their factory-preset values and 
restrict operations.
1. If using the remote control unit, press 
SIZE until “F” 
is displayed in the upper left area of the screen, then 
while “F” is being displayed, press 
, , , and 
 in that order.
  If using the monitor buttons, press 
 and  at the 
same time until “F” is displayed in the upper left area 
of the screen, then while “F” is being displayed, press 
 and  at the same time.
OFF
UNLOCKED ON
ON
LED
OFF
FUNCTION 1/1 
ALL...

17E
Controlling the Monitor with a PC (RS-232C)
You can control this monitor from a PC via RS-232C (COM 
port) on the PC.
You can also connect multiple monitors via a daisy chain by 
using a PC. By assigning ID numbers to each monitor (see 
page 18), you can make input mode selection/adjustment or 
can check the status of a specific monitor.Precautions when the PN-ZB02 (optional) is attached
•  To control the monitor via RS-232C, set RS-232C/LAN 
SELECT to RS-232C.
•  You cannot use RS-232C and LAN...

E18
Controlling the Monitor with a PC (RS-232C)
n Response code format
When a command has been executed correctly
O 
K Return code
(0DH, 0AH)
A response is returned after a command is executed.
*  If an ID number has been assigned
O  K SPC  0 0  1 
ID number of responding monitor 
Space (20
H) Return code
(0DH, 0AH)
When a command has not been executed
R 
R 
E Return code
(0DH, 0AH)
*  If an ID number has been assigned
R  R 
E  SPC 0 0  1 
ID number 
Space (20H)  Return code
(0DH, 0AH)
TIPS
• 
“ERR” is...

E19
Controlling the Monitor with a PC (RS-232C)
n Commands for ID control
The command examples shown on this page assume the 
following connection and ID number set up.
ID number: 1 
ID number: 2  ID number: 3 ID number: 4
IDST ......... A monitor receiving this command sets its own ID 
number in the parameter field.
 Example: IDST0001
OK 
  001 ←The ID number of this monitor is set to 1.
TIPS
You can automatically assign ID numbers by using the IDST 
command with the Repeater control (see “Repeater...

E20
Controlling the Monitor with a PC (RS-232C)
n Repeater control
This system has a function to allow setting of multiple 
monitors connected in a daisy chain using a single command. 
This function is called repeater control. You can use Repeater 
control function without assigning ID numbers.
[Example] 
Set 1 
  Set 2 
Set 3S et 4
*  If monitors are connected as shown above, you can 
execute a command like “Set all monitors’ input settings to 
PC D-SUB”.
nRepeater control command
Repeater control is...