Sharp Pn S525 Operation Guide

11E
You can return the settings to their factory-preset values and 
restrict operations.
1. After pressing 
SIZE for about 5 seconds, press  , 
 ,  , and  in that order.
OFF 
UNLOCKED  ON 
ON 
LED 
OFF 
FUNCTION 1/1 
ALL  RESET 
ADJUSTMENT LOCK 
RS-232C/LAN 
OSD DISPLAY  
LED 
TEMPERAT URE ALERT 
ST AT US  ALERT 
END…
[MENU]
2.  Select and set the items.
ALL RESET
Resets the settings to the factory default settings.  
Press 
 , select the resetting method, and then press MENU.
After initialization, turn...

12E
Controlling the Monitor with a PC (RS-232C)
You can control this monitor from a PC via RS-232C (COM 
port) on the PC.
You can also connect multiple monitors via a daisy chain by 
using a PC. By assigning ID numbers to each monitor (see 
page 13), you can make input mode selection/adjustment or 
can check the status of a specific monitor.
Caution
• To control the monitor via RS-232C, set RS-232C/LAN 
SELECT to RS-232C.
•  You cannot use RS-232C and LAN control simultaneously.
PC connection
nOne-to-one...

E13
Controlling the Monitor with a PC (RS-232C)
n Response code format
When a command has been executed correctly
O 
K Return code
(0DH, 0AH)
A response is returned after a command is executed.
*  If an ID number has been assigned
O  K SPC  0 0  1 
ID number of responding monitor 
Space (20
H) Return code
(0DH, 0AH)
When a command has not been executed
R 
R 
E Return code
(0DH, 0AH)
*  If an ID number has been assigned
R  R 
E  SPC 0 0  1 
ID number 
Space (20H)  Return code
(0DH, 0AH)
TIPS
• 
“ERR” is...

E14
Controlling the Monitor with a PC (RS-232C)
n Commands for ID control
The command examples shown on this page assume the 
following connection and ID number set up.
ID number: 1 
ID number: 2  ID number: 3 ID number: 4
IDST .........  A monitor receiving this command sets its own ID 
number in the parameter field.
 Example: IDST0001
OK 
  001 ←The ID number of this monitor is set to 1.
TIPS
You can automatically assign ID numbers by using the IDST 
command with the Repeater control (see “Repeater...

E15
Controlling the Monitor with a PC (RS-232C)
n Repeater control
This system has a function to allow setting of multiple 
monitors connected in a daisy chain using a single command. 
This function is called repeater control. You can use Repeater 
control function without assigning ID numbers.
[Example] 
Set 1 
  Set 2 
Set 3S et 4
*  If monitors are connected as shown above, you can 
execute a command like “Set all monitors’ input settings to 
PC1 DVI-D”.
nRepeater control command
Repeater control is...

E16
RS-232C command table
How to read the command tableCommand:  Command field (See page 12.)
Direction:  W When the “Parameter” is set in the parameter field (see page 12), the command functions as described 
under “Control/Response Contents”.
  R The returned value indicated under “Reply” can be obtained by setting “????”, “
?” or “???+” 
(repeater control) in the parameter field (see page 12).
Parameter:  Parameter field (See page 12.)
Reply:  Response (Returned value)
*:  “A” indicates a command...

E17
PICTURE menu
FunctionCommandDirectionParameter Reply Control/Response contents *
AUTO AGINW 1When the input mode is PC3, PC4. -
CONTRAST CONTWR 0-600-600-127 on PC3/PC4.
B
BLACK LEVEL
BLVLWR 0-600-600-127 on PC3/PC4.
TINT TINTWR 0-600-60
COLORS COLRWR 0-600-60
SHARPNESS SHRPWR 0-240-24
ADVANCED
(When the input 
mode is AV.) FLESH TONE
FLESWR 0-20-20: OFF, 1: LOW, 2: HIGH
B
3D-NR
TDNRWR 0-20-20: OFF, 1: LOW, 2: HIGH
MPEG-NR MPNRWR 0-10-10: OFF, 1: ON
3D-Y/C YCSPWR 0-10-10: OFF, 1: ON   (When the input...

E18
SETUP menu
FunctionCommandDirectionParameter Reply Control/Response contents *
OSD H-POSITION  OSDHWR 0-1000-100
B
OSD V-POSITION OSDVWR 0-1000-100
MONITOR STDRWR 0-10-10: LANDSCAPE, 1: PORTRAIT B
LANGUAGE LANGWR 1414ENGLISH
B
1
1DEUTSCH
2 2FRANÇAIS
3 3ITALIANO
4 4ESPAÑOL
5 5РУССКИЙ
6 6
 
HDMI AUTO VIEW HDAWWR 0-10-10: OFF, 1: ON B
Power On Delay PWODWR 00OFF
B
1-60 1-60ON
STANDBY MODE STBMWR 0-10-10: STANDARD, 1: LOW POWER B
RS-232C/LAN SELECT CTLSWR 0-10-10 : RS-232C 1 : LAN B
RS-232C/LAN COMMAND...

E19
ENLARGE menu (When the input mode is PC)
FunctionCommandDirectionParameter Reply Control/Response contents *
ENLARGE MODE EMAGWR 0-40-40: OFF, 1: 2 x 2, 2: 3 x 3, 3: 4 x 4, 4: 5 x 5
-
EMHV
WR 11-5511-551 x 1 (OFF) to 5 x 5 (“m x n” is expressed as “mn”, where m and n are 
the numbers of monitors specified for the longest direction and the 
shortest direction respectively.)
BEZEL WIDTH WIDTH OF THE
SHORTER SIDEBEZH
WR 0-1000-100
WIDTH OF THE
LONGER SIDE BEZV
WR 0-1000-100
IMAGE POSITION (M x N) EPHVWR...

E20
Controlling the Monitor with a PC (RS-232C)
PIP/PbyP menu
FunctionCommand DirectionParameter Reply Control/Response contents *
PIP MODES MWINWR 0-30-30: OFF, 1: PIP, 2: PbyP, 3: PbyP2 B
PIP SIZE MPSZWR 1-121-12 B
PIP POS THE LONGEST 
DIRECTION MHPS
W 0-100 B
R 0-100 B
THE SHORTEST  
DIRECTION MVPS
W 0-100 B
R 0-100 B
PIP POS LD+SD BATCH MPOSW 0-100,0-100 Specify the position in MPOSxxxyyy format. 
(xxx: Longer side, yyy: Shorter side position) B
R 0-100,0-100Returns a response in (xxx,yyy) format....