Sharp MX M452N User Manual

							39
MAINTENANCE
REPLACING THE TONER COLLECTION CONTAINER
The toner collection container collects excess toner that is produced during printing. When the toner collection container 
becomes full, Replace used toner container. will appear. Follow the procedure below to replace the toner collection 
container.
1Open the front cover.
2Remove the toner collection container. 
(1) Tilt the toner collection container forward.
Grasp the corners of the toner collection container with 
both hands as shown and tilt it forward until it stops.
(2) Slowly lift the toner collection container up.
3Place the box on a flat surface.
Place a sheet of newspaper on the surface before placing the 
box.
Do not point the holes down as used toner will spill out.
4Remove the provided cap from the side 
of the toner collection container.
Grasp the end of the cap and pull forward.
Downloaded From ManualsPrinter.com Manuals 
						

							40
MAINTENANCE
5Plug the hole in the toner collection 
container with the cap.
Push the cap in firmly so that toner will not leak out.
Do not discard the toner collection container. Place it in a plastic bag and keep it until your service technician comes to 
perform maintenance. Your service technician will collect the toner collection container.
6Install the new toner collection 
container.
Insert the box from above at a slant. 
7Push the toner collection container into 
the machine.
Push the box in until it clicks into place.
8Close the front cover.
Caution
Do not throw the toner collection container into a fire. Toner may fly and cause burns.
 Store the toner collection container out of the reach of small children.
When replacing the toner collection container, be aware that it may soil your clothes or the immediate surroundings.
Downloaded From ManualsPrinter.com Manuals 
						

							41
MAINTENANCE
REPLACING THE STAMP CARTRIDGE
If a stamp unit (AR-SU1) is installed on the automatic document feeder and the stamp has become faint, replace the 
stamp cartridge (AR-SV1).
Supplies
Stamp cartridge (2 in package) AR-SV1
1Open the automatic document feeder.
2Open the holders on the automatic 
document feeder that hold the original 
pressure sheet.
Open the holders (two) on the left and right sides.
3Grasp the tab on the stamp unit and pull 
the unit out.
4Remove the stamp cartridge (A).
Tab
(A)
Downloaded From ManualsPrinter.com Manuals 
						

							42
MAINTENANCE
5Install a new stamp cartridge.
6Push the stamp unit back in.
Push the stamp unit in until it clicks into place.
7Replace the original pressure sheet.
Push the holders in until they click into place.
8Close the automatic document feeder.
Downloaded From ManualsPrinter.com Manuals 
						

							43
REMOVING MISFEEDS
When a paper misfeed occurs, the message A misfeed has occurred. will appear in the touch panel and printing and 
scanning will stop. In this event, touch the [Information] key in the touch panel. When the key is touched, instructions for 
removing the misfeed will appear. Follow the instructions. When the misfeed is cleared, the message will automatically 
clear.
The blinking   mark in the image at left indicates the approximate position of the misfeed.
For detailed procedures for removing misfeeds, see REMOVING MISFEEDS in 8. TROUBLESHOOTING in the 
Operation Guide.
1Touch the [Information] key to display the following screen.
(A) Instructions for removing the misfeed appear here.
(B) Animation showing what to do.
(C) Display the previous screen or the next  screen.
(D) This closes the information screen.
The information screen cannot be closed until the misfeed 
is removed.
InformationOK
ExitOpen the centre cover and remove the misfed originals.Misfeed Removal
BackNext
A misfeed has occurred.
Turning M/C off now causes data loss.
(C)
(B)
(A)
(D)
Misfeed location
 While the message appears, printing and scanning cannot be resumed.
 If the message does not clear even after the misfeed has been removed, the causes below are possible. Check  once again.
 The misfeed was not correctly removed.
 A torn piece of paper remains in the machine.
 A cover or unit that was opened or moved to remove the misfeed was not returned to its original position.
Downloaded From ManualsPrinter.com Manuals 
						

							44
SUPPLIES
Standard supplies for this product that can replaced by the user include paper, toner cartridges, and staple cartridges for 
the finisher.
Be sure to use only SHARP-specified products for the toner cartridges, finisher staple cartridge, saddle stitch finisher 
staple cartridge, and transparency film.
Storage of supplies
Proper storage
1. Store the supplies in a location that is: clean and dry,
 at a stable temperature,
 not exposed to direct sunlight.
2. Store paper in the wrapper and lying flat.
3. Paper stored in packages standing up or out of the wrapper may curl or become damp, resulting in paper misfeeds.
Storing toner cartridges
Store a new toner cartridge box horizontally with the top side up. Do not store a toner cartridge standing on end. If stored 
standing on end, the toner may not distribute well even after shaking the cartridge vigorously, and will remain inside the 
cartridge without flowing out.
Staple cartridge
The finisher and saddle stitch finisher require the following staple cartridge:
MX-SCX1 (for finisher and saddle stitch finisher)
Approx. 5000 per cartridge x 3 cartridges
AR-SC2 (for finisher (large stacker))
Approx. 5000 per cartridge x 3 cartridges
AR-SC3 (for saddle stitch finisher only)
Approx. 2000 per cartridge x 3 cartridges
Supply of spare parts and consumables 
The supply of spare parts for repair of the machine is guaranteed for at least 7 years following the termination of 
production. Spare parts are those parts of the machine which may break down within the scope of the ordinary use of 
the product, whereas those parts which normally exceed the life of the product are not to be considered as spare parts. 
Consumables too, are available for 7 years following the termination of production. For best copying results, be sure to use only Sharp Genuine Supplies which are designed, 
engineered, and tested to maximize the life and performance of Sharp products. Look for the 
Genuine Supplies label on the toner package.
GENUINE SUPPLIES
Downloaded From ManualsPrinter.com Manuals 
						

							45
SPECIFICATIONS
Machine specifications / copier specifications
*1 Warm-up time may vary depending on some environments.
*2 First print time may vary depending on the status of the machine.
NameDigital Multifunctional System MX-M282N/MX-M362N/MX-M452N/MX-M502N
TypeDesktop
Photoconductive typeOPC drum
Printing methodElectrophotographic system (laser)
Developer systemDry-type two-component magnetic brush development
Fusing systemHeat rollers
Scanning resolutionDocument glass600 x 300 dpi (factory default values), 600 x 400 dpi, 600 x 600 dpi
Automatic document feeder600 x 300 dpi (factory default values), 600 x 400 dpi, 600 x 600 dpi
Printing resolution600 x 600 dpi
Scanning gradation256 levels
Printing gradationEquivalent to 256 levels
Original sizes / typesMax. A3 (11 x 17) / sheets, bound documents
Copy sizesMaximum: A3W (12 x 18) Minimum: A5R (5-1/4 x 5-3/4)
Print marginsLeading edge / trailing edge: total 8 mm (21/64) or less, 
near edge / far edge: total 4 mm ±2 mm (11/64 ±3/32) or less
Warm-up time*120 seconds or less
First-copy time*2MX-M282N/MX-M362N: 4.6 seconds or less
MX-M452N/MX-M502N: 3.9 seconds or less
Copy ratios
Variable: 25% to 400% in increments of 1%, total 376 increments (25% to 200% when the automatic document feeder is used)
Fixed presets:
25%, 50%, 70%, 81%, 86%, 100%, 115%, 122%, 141%, 200% and 400% for AB sizes;
25%, 50%, 64%, 77%, 100%, 121%, 129%, 200% and 400% for inch sizes
.
Two reduction ratios and two enlargement ratios can be stored.
Continuous copy999 copies
Automatic document 
feederSee Automatic document feeder specifications.
Tray 1 / Tray 2
Paper sizes: A3, B4, A4, A4R, B5, B5R, A5R, 11 x 17, 8-1/2 x 14, 8-1/2 x 13-1/2,  8-1/2 x 13-2/5, 8-1/2 x 13, 8-1/2 x 1 1, 8-1/2 x 11R, 7-1/4 x 10-1/2R, 
5-1/2 x 8-1/2R, 8K, 16K, 16KR
Paper weight: Plain paper (60 g/m
2 to 105 g/m2 (16 lbs. to 28 lbs.)), heavy paper (106 g/m2 to 
209 g/m2 (28 lbs. bond to 110 lbs. index))
Paper capacity: Plain paper (80 g/m2 (21 lbs.)) 500 sheets, heavy paper 200 sheets
Paper types: SHARP-recommended plain paper, recycled paper, coloured paper, and heavy paper
Downloaded From ManualsPrinter.com Manuals 
						

							46
SPECIFICATIONS
Machine specifications / copier specifications (Continued)
*1 Output tray (Centre tray) cannot be used when the finisher or saddle stitch finisher is installed.
*2 Type A connectors are located on the front of the machine and on the right side of the machine at the back (total of two connectors).
Do not use the connectors simultaneously.
When a keyboard is not connected (MX-KBX2), only one connector can be used; simultaneous use is not possible. If you need to 
change the connector that is used, contact your service technician.
To receive power supplied from a type A connector, the total current consumption of the connected device should not exceed 
500 mA.
Bypass tray
Paper sizes: A3W, A3, B4, A4, A4R, B5, B5R, A5R, envelopes, 12 x 18, 11 x 17, 8-1/2 x 14,  8-1/2 x 13-1/2, 8-1/2 x 13-2/5, 8-1/2 x 13, 8-1/2 x 11, 8-1/2 x 11R, 
7-1/4 x 10-1/2R, 5-1/2 x 8-1/2R, 8K, 16K, 16KR (Includes automatic paper size 
detection function. Entry of paper sizes up to 297 mm x 432 mm (11-5/8 x 17) is 
possible.)
Paper weights:
Thin paper (56 g/m
2 to 59 g/m2 (15 lbs. to 16 lbs.)), plain paper (60 g/m2 to 105 g/m2 (16 lbs. to 
28 lbs.)), heavy paper (106 g/m2 to 209 g/m2 (28 lbs. bond to 110 lbs. index)),
envelopes (75 g/m2 to 90 g/m2 (20 lbs. to 24 lbs.))
Paper capacity: Standard paper 100 sheets
Paper types:
SHARP-recommended plain paper, recycled paper, coloured paper, heavy paper, thin paper, 
transparency film, labels, tab paper, envelopes (Monarch, Com-10, DL, C5)
Duplex module
Paper  sizes: A3, B4, A4, A4R, B5, B5R, A5R, 11 x 17, 8-1/2 x 14, 8-1/2 x 13-1/2, 8-1/2 x 13-2/5,  8-1/2 x 13, 8-1/2 x 11, 8-1/2 x 11R, 5-1/2 x 8-1/2R, 8K, 16K, 16KR
Paper weight: Plain paper (60 g/m2 to 105 g/m2 (16 lbs. to 28 lbs.)), heavy paper (106 g/m2 to 
209 g/m2 (28 lbs. bond to 110 lbs. index))
Paper types: SHARP-recommended plain paper, recycled paper, coloured paper, and heavy paper
Output tray (Centre tray)*1
Output method: Face-down output (A3W and 12 x 18 paper can be output to right tray, finisher, or  saddle stitch finisher)
Output capacity: 400 sheets (using SHARP-recommended A4 or 8-1/2 x 11 paper)
(The maximum number of sheets that can be held varies depending on ambient conditions in the 
installation location, the type of paper, and the storage conditions of the paper.)
Tray full sensor: Yes
Interface port
LAN connectivity: 10Base-T / 100Base-TX / 1000Base-T
USB connectivity:
Type A connector supports USB 2.0*2
Compatibility requirements of USB memory
Memory capacity : Max. 32 GB
Disk Format : FAT32 only
Type B connector supports USB 2.0 (Hi speed)
Required power supplyLocal voltage ±10% (For the power supply requirements, see the name plate in the  lower corner of 
the left side of the machine.)
Power consumption1.84 kW (220-240 V) / 1.44 kW (100-127 V)
Dimensions
645 mm (W) x 695 mm (D) x 953 mm (H) (25-25/64 (W) x 27-3/8 (D) x 37-33/64 (H)) (With the 
reversing single pass feeder installed)
645 mm (W) x 695 mm (D) x 833 mm (H) (25-25/64 (W) x 27-3/8 (D) x 32-51/64 (H)) (With the 
document cover installed)
WeightApprox. 95 kg (209.4 lbs.) (With the reversing single pass feeder installed)
Approx. 88 k
g (194.0 lbs.) (With the document cover installed)
Overall dimensions986mm (W) x 695mm (D) (38-53/64 (W) x 27-3/8 (D)) (when bypass tray is extended)
Downloaded From ManualsPrinter.com Manuals 
						

							47
SPECIFICATIONS
Continuous copying speeds*
* Copy speed during output of the second copy and following copies when performing continuous one-sided copying of the same page (excluding offset output) using plain one-sided paper from a tray other than the bypass tray.
Chemical emission (measured according to RAL UZ-122: Edition Jan. 2006)
ModelMX-M282N MX-M362N MX-M452NMX-M502N
Copy ratio100% / Reduced / Enlarged
 A3, 11 x 17, 8K15 copies/min. 17 copies/min. 20 copies/min. 22 copies/min.
B4, 8-1/2 x 14, 8-1/2 x 13-1/2, 
8-1/2 x 13-2/5, 8-1/2 x 1317 copies/min. 20 copies/min. 23 copies/min. 25 copies/min.
A4, B5, 8-1/2 x 11, 16K28 copies/min. 36 copies/min. 45 copies/min. 50 copies/min.
A4R, B5R, 8-1/2 x 11R, 
7-1/4 x 10-1/2R, 16KR20 copies/min. 25 copies/min. 30 copies/min. 30 copies/min.
Ambient environment
Ozone1.5 mg/h or less
Dust4.0 m g/h or less
Styrene1.0 m g/h or less
Benzeneless than 0.05 m g/h
TVOC10 m g/h or less
85%
(Humidity)
(Temperature)
60%
20%
10°C
(54°F) 30°C
(86°F) 35°C
(91°F)
Downloaded From ManualsPrinter.com Manuals 
						

							48
SPECIFICATIONS
Acoustic noise emission (measurement according to ISO7779)
Reversing single feeder specifications (MX-RP11)
*1 Scanning in mono 2 mode of one side only is possible in fax and scan send modes. However, when the resolution is 600 x 600 dpi 
in Internet fax mode, the maximum length is 800 mm (31-31/64). When the resolution is 400 x 400 dpi or 600 x 600 dpi in scan 
mode, a long original cannot be scanned.
*2 Paper weights from 35 g/m
2 (9 lbs.) to 49 g/m2 (13 lbs.) require the use of slow scan mode.
Exit tray unit (right tray) specifications
* The maximum number of sheets that can be held varies depending on ambient conditions in the installation location, the type of  
paper, and the storage conditions of the paper. Envelopes and tab paper cannot be output. MX-M282N MX-M362N MX-M452N MX-M502N
Sound power level L
wA
Printing mode (continuous printing)6.4B6.6B6.7B6.8B
Standby mode4.0B4.6B4.6B4.6B
Sound pressure level L
pA (actual measurement)
Printing modeBystander positions50 dB (A) 52 dB (A) 53 dB (A) 54 dB (A)
Operator positions51 dB (A) 52 dB (A) 53 dB (A) 53 dB (A)
Standby modeBystander positions27 dB (A) 32 dB (A) 32 dB (A) 32 dB (A)
Operator positions28 dB (A) 34 dB (A) 32 dB (A) 31 dB (A)
Original sizesA3 to A5, 11 x 17 to 5-1/2 x 8-1/2, long paper 
(max. width 297 mm (11-5/8) x max. length 1000 mm*1 (39-23/64))
Original weightOne-sided 35g/m2  to 128g/m2 (9 lbs. to 32 lbs.)*2
Two-sided 50g/m2 to 105g/m2 (13 lbs. to 28 lbs.)
Capacity100 sheets (80 g/m2 (21 lbs.)) Maximum stack height of 13 mm (1/2)
ModelMX-TRX2
Output methodFace-down output
Output capacity*100 sheets (using SHARP-recommended A4 or 8-1/2 x 11 paper)
Dimensions
When tray is folded up:
314 mm (W) x 405 mm (D) x 52 mm (H) (12-23/64 (W) x 15-61/64 (D) x 2-3/64 (H))
When tray is extended:
444 mm (W) x 405 mm (D) x 52 mm (H) (17-31/64 (W) x 15-61/64 (D) x 2-3/64 (H))
WeightApprox. 0.93 k g (2 lbs.)
Downloaded From ManualsPrinter.com Manuals