Sharp MX M363N User Manual

2-109
COPIER
Contents
4
Touch the [OK] key.
You will return to the special modes screen. Touch the [OK] key 
to return to the base screen of copy mode.
5
Press the [START] key.
Copying will begin.
If you have selected sort mode, change originals and press the [START] key. Repeat until all pages have been scanned and 
then touch the [Read-End] key.
To cancel scanning and copying...
Press the [STOP] key ( ).
 The original must be placed on the document glass.
 Overlap of sections of image
- There will be a...

2-110
COPIER
Contents
REVERSING THE IMAGE (Mirror Image)
This feature is used to make a copy that is a mirror image of the original.
1
Place the original.
Place the original face up in the document feeder tray, or face down on the document glass.
2
Select the special modes.
(1) Touch the [Special Modes] key.
(2) Touch the   keys to switch through the screens.
(3) Touch the [Image Edit] key.
☞[Image Edit] KEY (page 2-104)
3
Select Mirror Image.
(1) Touch the [Mirror Image] key so that it is 
highlighted....

2-111
COPIER
Contents
COPYING A3 (11 x 17) ORIGINALS WITH NO EDGE 
CUT-OFF (A3 (11 x 17) Full Bleed)
This feature lets you copy an entire A3 (11 x 17) size original at full size with no image cut-off at the edges.
A3W (12 x 18) size paper is used, which is slightly larger than A3 (11 x 17) size.
1
Place the original face down on the 
document glass.
2
Select the special modes.
(1) Touch the [Special Modes] key.
(2) Touch the   keys to switch through the screens.
(3) Touch the [Image Edit] key.
☞[Image...

2-112
COPIER
Contents
4
Place A3W (12 x 18) paper in the 
bypass tray.
Pull out the extension tray, adjust the guides to the width of 
A3W (12 x 18) paper, and place the paper in the bypass tray.
After loading the paper, configure the bypass tray settings as 
explained in MAKING COPIES USING THE BYPASS TRAY 
(page 2-38).
5
Press the [START] key.
Copying will begin.
If you have selected sort mode, change originals and press the [START] key. Repeat until all pages have been scanned and 
then touch the...

2-113
COPIER
Contents
COPYING IN THE CENTRE OF THE PAPER (Centring)
This is used to centre the copied image on the paper.
This lets you place the image in the centre of the paper when the original size is smaller than the paper size or when the 
image is reduced.
Not using the centring functionUsing the centring function
1
Place the original.
Place the original face up in the document feeder tray, or face down on the document glass.
2
Select the special modes.
(1) Touch the [Special Modes] key.
(2) Touch...

2-114
COPIER
Contents
 The image can be reduced when using the centring function, but not enlarged.
 When the original size or the paper size is displayed as a special size, this function cannot be used.
To cancel centring...
Touch the [Centring] key in the screen of step 3 so that it is not highlighted.
Downloaded From ManualsPrinter.com Manuals 

2-115
COPIER
Contents
ADJUSTING THE SHARPNESS OF AN 
IMAGE (Sharpness)
This is used to sharpen an image or make it softer.
1
Place the original.
Place the original face up in the document feeder tray, or face down on the document glass.
2
Select the special modes.
(1) Touch the [Special Modes] key.
(2) Touch the   keys to switch through the screens.
(3) Touch the [Sharpness] key.
3
Adjust the image.
(1) Touch the [Soft] key or the [Sharp] key so 
that it is highlighted.
(2) Touch the [OK] key.
You will...

2-116
COPIER
Contents
CHECKING COPIES BEFORE PRINTING
(Proof Copy)
This feature prints only one set of copies, regardless of how many sets have been specified. After the first set is checked 
for errors, the remaining sets can be printed. Previously it was necessary to re-scan the original each time changes to 
settings were required. However, this feature makes it possible to change settings for the scanned original without 
scanning it again, allowing you perform copying more efficiently.
1
Place the...

2-117
COPIER
Contents
4
Set the number of copies (number of 
sets) with the numeric keys.
If you will copy multiple originals using the document glass, 
switch to sort mode after this step.
☞Sort mode (page 2-33)
Up to 999 copies (sets) can be set.
If an incorrect number of copies is set...
Press the [CLEAR] key ( ) and then enter the correct number.
5
Press the [START] key.
One set of copies is printed.
If you are using the document glass to copy multiple originals, change originals and press the...

2-118
COPIER
Contents
7
Change the settings.
(1) Touch the key of the setting that you want 
to change.
The setting screen of the touched key opens. Change the 
settings and touch the [OK] key.
(2) Touch the [OK] key.
 To change the number of sets printed, set the desired number of copies (sets) with the numeric keys. After changing 
the number of sets, touch the [End] key in the touch panel (not the [START] key) to print the sets.
 Special modes that can be adjusted are Margin Shift, Pamphlet Copy,...