Sharp MX M160 User Manual

79
SYSTEM SETTINGS GUIDE
7
ACCOUNT CONTROL
These programs are used to control use of the 
machine by account. To access one of these 
programs, select ACCOUNT CONTROL in the mode 
selection screen, select the desired program in the 
account control screen, and press the [OK] key.
AUDITING MODE
This program is used to enable auditing mode for 
copy, print, and scan mode. To enable auditing mode 
for fax mode, see the Operation manual (for 
facsimile).
When auditing mode is enabled, a count is kept of the...

80
SYSTEM SETTINGS GUIDE
Resetting a single account
1Select RESET 1 ACC. with the [ ] or [ ] 
key and then press the [OK] key.
2Select the desired account with the [ ] or 
[ ] key.
If ---,--- appears for a page limit, a limit has not been 
set.
3Select the desired mode with the [ ] or 
[ ] key and then press the [OK] key.
4Press the [ ] or [ ] key to select YES 
and then press the [OK] key.
5If you wish to reset the page counts of 
another account, repeat steps 2 to 4.
6To exit, press the [BACK] key...

81
SYSTEM SETTINGS GUIDE
7
ACCOUNT LIMIT
This program is used to set limits for the number of 
pages that can be printed by each account in print 
mode and copy mode.
Select ACCOUNT LIMIT and press the [OK] key. The 
following screen appears.
Limiting the number of pages used by an 
account
1Select SINGLE ACC. LIMIT with the [ ] 
or [ ] key and then press the [OK] key.
2Select COPIER or PRINTER mode with 
the [ ] or [ ] key.
3Press the [OK] key.
4Enter the desired account number with the 
numeric keys....

82
SYSTEM SETTINGS GUIDE
DEVICE CONTROL
These programs are used to configure settings for 
hardware functions of the machine. To access one of 
these programs, select DEVICE CONTROL in the 
mode selection screen, select the desired program in 
the device control screen, and press the [OK] key.
WAITING COPY LAMP SETTING
This program is used to select whether the copy lamp 
(light source) is on or off when the machine is in standby 
mode. If the copy lamp (light source) is set to turn off in 
standby mode,...

83
SYSTEM SETTINGS GUIDE
7
RETURN FROM COPY MODE TIMING
When there are print jobs or fax print jobs waiting to be 
printed after copy job is finished, this program is used 
to set a brief wait time until printing of those jobs 
begins. Setting a brief wait time allows another copy 
job to be performed following the previous copy job.
Time selections are 0 sec., 10 sec., 30 sec., and 
60 sec..
The factory default setting is 30 seconds.
Select RETURN FROM COPY MODE TIMING and 
press the [OK] key. The...

84
SYSTEM SETTINGS GUIDE
Select MESSAGE TIME and press the [OK] key. The 
following screen will appear.
1Select the desired display time with the 
[ ] or [ ] key.
2Press the [OK] key.
KEY TOUCH SOUND
This program is used to set the volume of the key 
touch sound that is heard each time a key is pressed.
The initial factory setting is SHORT.
Select KEY TOUCH SOUND and press the [OK] key. 
The following screen will appear.
1Select the desired volume with the [ ] or 
[ ] key.
To turn the key touch sound...

85
SYSTEM SETTINGS GUIDE
7
To enable the setting, select DISABLE PAPER 
SIZE SET and press the [OK] key so that a 
checkmark appears in the checkbox.
To disable the setting, select DISABLE PAPER 
SIZE SET once again and press the [OK] key so 
that the checkmark is cleared from the checkbox.
ENERGY SAVE
These programs are used to configure energy saving 
settings. To access one of these programs, select 
ENERGY SAVE in the mode selection screen, and 
select the desired program in the energy save screen,...

86
SYSTEM SETTINGS GUIDE
COPY SETTINGS
These programs are used to enable various copy 
functions. To access one of these programs, select 
COPIER in the mode selection screen, select the 
desired program in the copy settings screen, and 
press the [OK] key.
EXPOSURE ADJUST
This program is used to adjust the exposure level 
when AUTO is used for the exposure mode. The 
auto exposure level can be set separately for the 
document glass and the SPF.
One of five levels can be selected, with the left end of...

87
SYSTEM SETTINGS GUIDE
7
Select DEFAULT TRAY SET and press the [OK] key. 
The following screen will appear.
1Select the tray with the [ ] or [ ] key.
2Press the [OK] key.
DEFAULT EXPOSURE
This program is used to select the exposure 
mode/level that is initially selected when the 
[EXPOSURE] key is pressed.
The factory default setting is AUTO.
Select DEFAULT EXPOSURE and press the [OK] 
key. The following screen will appear.
1Select the exposure mode with the [ ] or 
[ ] key.
2If you selected TEXT or...

88
SYSTEM SETTINGS GUIDE
RESOLUTION IN AUTO/TEXT MODE
This program is used to set the resolution used when 
the exposure mode is set to AUTO or TEXT. When 
300dpi is selected, the first copy time is shorter than 
when 600dpi is selected.
The factory default setting is 300dpi.
Select RESOLUTION IN AUTO/TEXT MODE and 
press the [OK] key. The following screen will appear.
1Press the [ ] or [ ] key to select the 
resolution.
2Press the [OK] key.
PHOTO MODE DEFAULT
This program is used to select the method of...