Sharp MX M160 User Manual

59
COPY FUNCTIONS
4
TWO-SIDED COPIES OF TWO-SIDED ORIGINALS 
(ONLY WHEN USING THE RSPF)
 Paper sizes that can be used are A3, B4, A4, A4R, B5, B5R, A5, 11 x 17, 8-1/2 x 14, 8-1/2 x 13, 8-1/2 x 11 
and 8-1/2 x 11R.
 Automatic two-sided copying is not possible when the bypass tray is used.
 This copy function cannot be used in combination with dual page copy.
1Make sure that an original does not 
remain on the document glass, and 
then adjust the original guides to the 
width of your originals and place...

60
COPY FUNCTIONS
ONE-SIDED COPIES OF TWO-SIDED ORIGINALS 
(ONLY WHEN USING THE RSPF)
 Paper sizes that can be used are A3, B4, A4, A4R, B5, B5R, A5, 11 x 17, 8-1/2 x 14, 8-1/2 x 13, 8-1/2 x 11 
and 8-1/2 x 11R.
 Automatic two-sided copying is not possible when the bypass tray is used.
 This copy function cannot be used in combination with dual page copy.
1Make sure that an original does not 
remain on the document glass, and 
then adjust the original guides to the 
width of your originals and place the...

61
4
TWO-SIDED COPIES USING THE 
BYPASS TRAY
Follow the steps below to perform two-sided copying manually.
Example: Copying original A and original B onto both sides of the paper
1Copy original A.
2Place original B as shown below.
Vertically-oriented 
original:
If the original is oriented 
vertically, place it in the 
same orientation as 
original A.
Horizontally-oriented 
original:
Place in the opposite 
orientation (rotated 180 
degrees) to that of 
original A.
3Turn the copy of original A over, and...

62
DUAL PAGE COPY(Dual page copy)
The dual page copy function produces separate copies of open bound original pages. This function is convenient 
when you wish to make a separate copy of each page of a book or other bound document.
1Place the original on the document 
glass, aligning the division between 
the pages with the size marker (see 
below). Close the SPF.
Copying will begin from the 
page to the right of the size 
marker.
2Press the [SPECIAL FUNCTION] key.
The special function 
screen will...

63
4
INTERRUPTING A COPY RUN
(Interrupt copying)
A copy run can be temporarily interrupted to allow another copy job to be performed. (Interrupt copying)
When the other job is finished, the copy run will resume using the original copy settings.
 Interrupt copying is not possible when the document glass is being used for a copy job and NO SORT is 
selected.
 When 2 in 1 or 4 in 1 is selected, interrupt copying is not possible.
 Sort copying, 2 in 1, and 4 in 1 and automatic two-sided copying cannot be...

64
5
CONVENIENT COPY 
FUNCTIONS
Select convenient copy functions after pressing the [COPY] key to select copy mode.
ROTATING THE IMAGE 90 DEGREES
(Rotation copy)
When Auto paper select mode or automatic ratio selection are in operation and the original is placed in a different 
orientation (vertical or horizontal) from the paper, the original image will be automatically rotated 90 degrees to 
enable correct copying onto the paper.
This function is convenient for copying B4 or A3 (8-1/2 x 14 or 11 x 17)...

65
CONVENIENT COPY FUNCTIONS
5
1Place the originals in the document 
feeder tray or the first original on the 
document glass.
If the originals are placed in the 
document feeder tray, sort 
mode will be automatically 
selected. This can be changed 
to no sort in the system settings. 
(Page 87)
If the first original is placed on the document glass, no 
sort mode will be automatically selected.
2Press the [OUTPUT] key.
The output mode 
selection screen will 
appear.
3Select NO SORT or SORT with the 
[ ]...

66
COPYING MULTIPLE ORIGINALS ONTO A 
SINGLE SHEET OF PAPER
(2 in 1 / 4 in 1 copy)
Multiple originals can be copied onto a single sheet of paper in a selected layout.
This function is convenient when you wish to present multiple pages in a compact format, or show a view of all 
pages in a document.
One of two layouts can be selected for 2 in 1 copy, and one of four layouts can be selected for 4 in 1 copy.
Border line selections are solid line, broken line, or none.
2 in 1 copy layouts
4 in 1 copy...

67
CONVENIENT COPY FUNCTIONS
5
5Select 2in1/4in1 with the [ ] or [ ] 
key.
6Press the [OK] key.
The 2 in 1 / 4 in 1 
selection screen will 
appear.
7Select 2in1 or 4in1 with the [ ] or 
[ ] key.
8Press the [OK] key.
The settings for 2 in 1 or 
4 in 1 will appear.
9Select the layout with the [ ] or [ ] 
key.
For the layouts that can be 
selected, see 2 in 1 copy 
layouts or 4 in 1 copy layouts 
on page 66.
10Select the borderline setting with the 
[] or [] key.
Select solid line, broken line, or none....

68
CREATING MARGINS WHEN COPYING(Margin shift)
The margin shift function shifts the image to create a margin at the edge of the paper. By default the function creates 
a 10 mm (1/2) margin at the left edge of the paper.
 You can select whether to create a margin at the top edge or at the left edge of the paper.
 Five selections are available for the margin width: 0 mm, 5 mm, 10 mm, 15 mm, 20 mm (0, 1/4, 1/2, 3/4, 1). 
(The default setting is 10 mm (1/2).)
 When making two-sided copies, a margin is...