Sharp MX 2700N User Manual

40
FINISHER
The finisher is equipped with the offset function, which offsets each set of output from the previous set.
In addition, each set of sorted output can be stapled.
An optional hole punching unit can also be installed to punch holes in output.
PART NAMES
The following parts can be accessed when the finisher is open.
(1) Output tray
Stapled and offset output is delivered to this tray.
The tray is slidable. Extend the tray for large output 
(A3W, A3, B4, 12 x 18, 11 x 17, 8-1/2 x 14 and 
8-1/2 x...

41
FINISHER MAINTENANCE
When the staple cartridge runs out of staples, a message will appear in the operation panel. Follow the procedure below 
to replace the staple cartridge.
Replacing the staple cartridge
1
Open the cover.
2
While pressing the lever over to the left, 
slide the finisher to the left until it stops.
Gently slide the finisher until it stops.
3
Lower the staple case release lever and 
remove the staple case.
Pull the staple case out to the right.
4
Remove the empty staple cartridge from...

42
Removing staple jams
Follow the steps below to remove a staple jam.
6
Replace the staple case.
Push the staple case in until it clicks into place.
7
Slide the finisher back to the right.
Gently slide the finisher back to the right until it locks into its 
original position.
8
Close the cover.
Make a test print or copy in staple sort mode to verify that stapling takes place correctly.
1
Open the cover.
2
While pressing the lever over to the left, 
slide the finisher to the left until it stops.
Gently...

43
3
Lower the staple case release lever and 
remove the staple case.
Pull the staple case out to the right.
4
Raise the lever at the front end of the 
staple case and remove the jammed 
staple.
Remove the leading staple if it is bent. If bent staples remain, a 
staple jam will occur again.
5
Lower the lever at the front end of the 
staple case.
6
Replace the staple case.
Push the staple case in until it clicks into place.
7
Slide the finisher back to the right.
Gently slide the finisher back to the...

44
Discarding punch waste (when a punch module is installed)
1
Open the cover.
2
Grasp the punch waste box handle, 
gently pull out the box, and discard the 
punch waste.
Discard the punch waste in a plastic bag or other container, 
taking care not to let the waste scatter.
3
Gently push the box back in.
4
Close the cover.
Downloaded From ManualsPrinter.com Manuals 

45
SADDLE STITCH FINISHER
The saddle stitch finisher is equipped with the offset function that offsets each set of output from the previous set, the 
staple sort function that staples each set of output, and the saddle stitch function that automatically staples and folds 
each set of output at the centreline.
An optional hole punching unit can also be installed to punch holes in output.
PART NAMES
(1) Stapler compiler
This temporarily stacks paper to be stapled.
(2) Output tray
Stapled and offset output...

46
SADDLE STITCH FINISHER MAINTENANCE
When the staple cartridge runs out of staples, a message will appear in the operation panel. Follow the procedure below 
to replace the staple cartridge.
Replacing the staple cartridge
1
Open the front cover.
2
Pull out the stapler section.
Pull out until the stapler section until it stops.
3
Turn roller rotating knob A in the 
direction of the arrow to move the staple 
unit out to the front.
Turn the roller rotating knob as shown until the triangle mark is 
aligned...

47
6
Insert a new staple cartridge into the 
staple case.
Push the staple cartridge in until it clicks into place.
Do not remove the seal from the cartridge before inserting the cartridge into the case.
7
Pull the seal that holds the staples 
straight out.
8
Replace the staple case.
Push the staple case in until it clicks into place.
9
Push the stapler section back in.
Push the stapler section back in until it locks into its original 
position.
10
Close the front cover.
Make a test print or copy in...

48
Removing staple jams
Follow the steps below to remove a staple jam.
1
While pulling the lever, slide the saddle 
stitch finisher to the left until it stops.
2
Open the front cover.
3
Turn roller rotating knob B as shown 
until the blue indicator is visible.
4
Remove any paper from the stapler 
compiler.
Be careful not to tear the paper during removal.
5
If the saddle stitch function was being 
used, open the saddle stitch section 
cover.
BlueRoller rotating knob B
Downloaded From ManualsPrinter.com...

49
6
Remove the misfed paper.
Be careful not to tear the paper during removal.
7
Close the saddle stitch section cover.
8
Pull out the stapler section.
Pull out until the stapler section until it stops.
9
Turn roller rotating knob A in the 
direction of the arrow to move the staple 
unit out to the front.
Turn the roller rotating knob until the triangle mark is aligned 
with the indicator.
10
Remove the staple case.
11
Raise the lever at the front end of the 
staple case and remove the jammed 
staple....