Sharp Lc M3700 Operation Manual

US
10
Part Names – Remote Control Unit
INPUT
RETURNMENU
STANDBY/ON
ENLARGEWIDE
LCD MONITOR
ENTER
VOL
Numbers within          refer to the main page(s) where the topic is explained.
Signal transmitterRemote control unit
STANDBY/ON
MENU···································· VOL +/– ··································30
ENLARGE
31 INPUT
31
RETURN
32
32
WIDE·····································
31 Cursor control ('/"/\/|)············
32
ENTER··································
32
31
 

11 US
Introduction
Removing the battery cover
Cautions regarding remote control unit
»Do not expose the remote control unit to shock. In addition, do not
expose the remote control unit to liquids, and do not place it in an
area with high humidity.
»The remote control unit may not work properly if the remote control
sensor is under direct sunlight or strong lighting.
In such cases, change the angle of the lighting or the monitor, or
operate the remote control unit closer to the remote control sensor....

US
12
Make sure the following accessories are provided
with the product.
Remote control unit (× 1)
INPUT
RETURNMENU
STANDBY/ON
ENLARGEWIDE
LCD MONITOR
ENTER
VOL
“AA” size battery (× 2)
Pages 11, 30 - 32 Page 11AC cord, 9 ft.10-
1/8″(3 m) (× 1)
Cable clamp (× 1)
Screw (× 1)
Cable binder (× 3) Page 19
Page 19
Page 29
Supplied Accessories
Terminal cover mounting screw (× 2)
Flat washer (× 2)
Caution:
»This monitor is equipped with a temporary stand when shipped from the factory. Please note this stand is...

13 US
Introduction
Connection
and Installation
INPUT1

 INPUT1: Terminals are provided for two types of video input signal.
 Input Select
No matter which video signal is selected, the system uses the signal input to the audio terminals for
audio.
Related topic:
 Input Select
*1“Auto” (automatic color system detection) is factory preset value. 
 Color System
54
54
57
INPUT 1
AUDIO
VIDEO S-VIDEOR - - L
1
S-videoINPUT1
audioVideo
Connecting Peripheral Equipment
Terminal type
BNC
S terminalCompatible...

US
14
Connecting Peripheral Equipment (Continued)
INPUT2
INPUT 2 (INPUT/OUTPUT)
VIDEOAUDIO R - - L
2
INPUT2
audio
Video
Terminal type
RCACompatible signals
NTSC (3.58/4.43), PAL, SECAM (*2) Video

INPUT2: Input or output can be selected for INPUT2.
 (*1)  INPUT2 Select
This setting cannot be switched when INPUT2 is currently being displayed.
When this is set to “Output”, video signals input from the INPUT1 video input terminal are output. (*3)
An audio signal is output with this setting (i.e. the audio...

15 US
Connection
and Installation
INPUT3


INPUT 3
AUDIO Pr/Cr/R Pb/Cb/B VDHD Y/G
3
Input Select: RGBINPUT3 audio
Input Select:
COMPONENTHorizontal
sync signal (H sync)Vertical
sync signal (V sync)
The signal is input with the Y/Pb/Pr (Y/Cb/Cr) terminals. The HD and VD terminals are 
not used. Video adjustment options on the menu are the AV type.
Compatible input range: 480i/576i, 480p/576p, 1080i (50Hz (*4) /60Hz), 720p (60Hz). (*1)
The monitor operates using Video (RGB) and Sync (HD/VD) signals,...

US
16
PC
Terminal type
D-Sub15-pin
DVI-DCompatible signals
VGA, SVGA, XGA, SXGA and others           Appendix 1
In addition to ordinary Separate Sync (HD/VD) signals, the system is also 
compatible with Composite Sync (Csync) and Sync On Green.  (*1) (*2)
VGA, SVGA, XGA, SXGA and others           Appendix 1 Analog
Digital
68
68
Connecting Peripheral Equipment (Continued)

PC: Terminals for two kinds of PC video input signal are available.
 Input Select
No matter which video signal is selected, the...

17 US
Connection
and Installation
VIDEO OUTPUT

When INPUT2 is displayed, video from INPUT2 is output. Otherwise video from INPUT1 is output.
INPUT3/PC (ANALOG) OUTPUT

When INPUT3 is displayed, video from INPUT3 is output. Otherwise PC (analog) video is output.
RS-232C INPUT/RS-232C OUTPUT

The RS-232C INPUT and RS-232C OUTPUT are used to control this monitor with a PC.
To connect a single monitor to a PC, connect to the RS-232C INPUT terminal.
To connect multiple monitors in a daisy chain for control...

US
18
Connecting External Speakers
Make sure to connect the speaker jack and cable polarity (±, —) properly.

The speaker jacks have plus ± and minus — polarity. Plus is red and minus is black.
The cables are also divided into plus and minus.
When connecting the left/right speakers, be sure to connect the plus/minus jacks with the correct
cables.
»You can output audio from the built-in monitor speaker on the back of the monitor.  See “Monitor Speaker Output”
on page 57 for details.
Speaker...

19 US
Connection
and Installation
Connecting the AC Cord
CautionBe sure to turn the main POWER off when connecting the cord.
»When connecting the power cord to the main unit, always
use the cable clamp to keep the power cord from coming
loose.
Fastening the AC cord
1. Plug the AC cord into the AC input terminal on the back
of the monitor.
»Align the shape of the plug and the connector, and
insert all the way in.
2. Attach the supplied cable clamp to the AC cord.
3. Align the hole of the cable clamp with...