Sharp LC-70C8470U, LC-60C8470U, LC-70C7450U, LC-60C7450U HDTV Owners Guide

							59
Presetting Remote Control Function
You can operate the connected AV products (AV 
receiver, cable box, SAT tuner, DTV, VCR, BD, DVD, 
LD) using the presetting manufacturer function of your 
remote control unit.
14
12
11
6
13
10
8
9
7
54 32
1
Presetting manufacturer codes
1   Press an appropriate button (STB,DVD•VCR or 
AUDIO) to operate the connected equipment.
2   Press an appropriate button (STB,DVD•VCR or 
AUDIO) and DISPLAY at the same time to enter 
the code registration mode.
3   Press 0–9 to enter the manufacturer code. (See 
page 60.)
•  Preset mode is fi nished once the LED no longer lights 
up.
4   After registering the code, the LED will stop blinking 
then turn off after one second. (If you perform an 
incorrect operation, the LED will blink quickly then 
turn off.)
Operating the Connected Equipment
To operate the connected equipment, press STB,
DVD•VCR or AUDIO to select your device. (STB 
(cable/satellite set-top box), BD, DVD, VCR or AUDIO.) 
The remote control unit button will function as follows.
•  When you operate VCR, DVD or BD, press INPUT to select 
the terminal connected to your device. 
•  CABLE and SAT cannot be selected at the same time.
1 POWER (SOURCE)  • Turns the connected equipment power on and off.
2,• Starts playback. (VCR, BD, DVD)
3*• Rewinds the tape and allows picture search. (VCR)
• Hold down to go in reverse. (BD, DVD)
4+• Stops the tape transport. (VCR)
• Playback stops when pressed. With some Blu-ray disc/
DVD players, pressing the button twice may open the 
disc tray. (BD, DVD)
5.• Pressing quickly once takes you to the start of the chapter 
currently playing. Each time you press it, you move back 
to the start of the previous chapter. (BD, DVD)
6 0–9,•(DOT) (STB)• Press a button (or buttons) that corresponds to the 
channel that you wish to watch.
7-• Rapidly advances the tape and allows picture search. 
(VCR)
• Hold down to fast forward. (BD, DVD)
8)• Sets pauses and still pictures. (VCR, BD, DVD)
9/• Pressing quickly once takes you to the start of the next 
chapter. Each time you press it, you move ahead to the 
start of the next chapter. (BD, DVD)
10(REC• Starts recording. (VCR)
11 FLASHBACK• Press to switch between the current channel and the 
channel you were watching immediately before. Some 
manufacturers do not preset FLASHBACK. (STB)
12CH
U/
V• Press CHU or CHV to tune in to a higher or lower 
channel. (STB)
• Press to select the channel of the TV tuner on the VCR. 
(VCR)
13 MENU• When this button is pressed, the BD/DVD menu will 
display. (BD, DVD)
14a/
b/
c/
d,ENTER•
a/
b/
c/
d: Press the button to select items on the STB 
GUIDE screen or STB MENU screen. (STB)
  Press the button to select items on the BD/DVD menu 
screen. (BD, DVD)
•ENTER: Press to activate the selected function. (STB, 
BD, DVD)
Other Viewing Options
-$@$6@6@&JOEC


-$@$6@6@&JOEC








 
						

							60
Manufacturer codes Other Viewing Options
AUDIO DYNAMICS
BROCKSONIC
CANON
CRAIG
CURTIS MATHIS
DBX
EMERSON
GE
INSTANT REOLYA
JC PENNEY
JVC
KENWOOD
MAGNAVOX
MAGNIN
MEMOREX
MONTGOMERY  WARD
NEC
PANASONIC
PENTAX
PHILCO
PHILIPS
QUASAR
REALISTIC
SAMSUNG
SHARP
SONY
SYLVANIA
TATUNG
TEAC
TMK
YAMAHA09
13
04
12
04
09
10, 13, 14
04
04
04
09, 16, 17, 22
09
04, 05, 06
12
04
02
09
04, 18, 19, 20, 21
05
04, 05
04, 05, 06
04
01, 02
11, 12
01, 02, 03
07, 08, 15
04, 05, 06
09
09
10
09
REMOTE CONTROL CODE 
NUMBER VCR BRAND
DENON
JVC
KENWOOD
MAGNAVOX
MARANTZ
MITSUBISHI
PANASONIC
PHILIPS
PIONEER
PROSCAN
RCA
SAMSUNG
SHARP
SONY
TOSHIBA
YAMAHA
ZENITH24
31
36
26
26
28
24, 37
26, 38
30, 33, 35
25
25, 39
29, 34
23, 32, 41, 42
27, 40
26
24
26
REMOTE CONTROL CODE 
NUMBER BD/DVD/LD BRAND
•  Depending on the brand, the codes of some BD players 
may not be supported.
ANVISION
CABLE STAR
DISH NETWORK
DIRECTV
EAGLE
G.INSTRUMENT
GERROLD
JERROLD
MAGNAVOX
MOTOROLA
OKA SIGMA
PANASONIC
PHILIPS
PIONEER
RANDTEK
RCA
S.ATLANTA
VIEWSTAR
ZENITH04, 05
04, 05
39, 40
41
05
02, 03, 10, 11, 17, 20
17
02, 03, 10, 11, 12, 20, 
25-34
04, 05, 08, 12, 15, 16, 
18, 19, 22, 23
38
07
14, 21
04, 05, 08, 13, 15, 16, 
18, 19, 22, 23
07
04, 05
14, 36*, 37*
01, 09, 24
04, 05, 08, 13, 15, 16, 
18, 19, 22, 23
06, 35
REMOTE CONTROL CODE 
NUMBER STB BRAND
•  Numbers marked with * are SAT codes, all others are STB 
codes.
SHARP
SHARP (SOUND BAR)01
02
AUDIO BRANDREMOTE CONTROL CODE 
NUMBER
-$@$6@6@&JOEC


-$@$6@6@&JOEC








 
						

							61
Using AQUOS LINK
Controlling HDMI Equipment Using AQUOS LINK
What’s AQUOS LINK?
•  Using the HDMI CEC (Consumer Electronics Control) protocol, with AQUOS LINK you can interactively operate 
compatible system equipment (Blu-ray disc equipment, AV amplifi er, DVD).
•  By connecting AQUOS LINK-compatible devices with HDMI-certifi ed cables to the TV, you can control a 
recorder or AV amplifi er using the remote control of the TV.
•  AQUOS LINK allows you to operate the HDMI-connected equipment with one remote control.
Back panel 
vertical inputs Back panel 
horizontal inputs
Example
AQUOS LINK-compatible 
Audio system AQUOS BD Player
HDMI-certified cable *
* Use HDMI 1 to connect 
   ARC-compatible equipment.
HDMI-certified cable  Optical fiber cableConnecting AQUOS 
BD Player via AQUOS 
LINK-compatible
Audio system 
•  For connecting the TV to AQUOS LINK-compatible equipment, use commercially available cables.
•  Point the remote control toward the TV, not to connected HDMI equipment.
•  Video noise may occur depending on the type of HDMI cable used. Make sure to use an HDMI-certifi ed cable.
•  Up to 3 pieces of HDMI recording equipment and one AV amplifi er can be connected using this system.
•  These operations affect the HDMI equipment selected as the current input source. If the equipment does not operate, turn on 
the equipment and select the appropriate input source using INPUT.
•  The AQUOS LINK feature may not operate properly when an HDMI splitter or AV selector unit is used. These devices may 
cause interruptions to the image and/or sound.
Connected AQUOS LINK-compatible devices can be operated without 
changing the settings of the remote control unit. 
OPTION button will function only when AQUOS LINK is used.
■ One Touch Play
While the TV is in standby mode, it automatically turns on and plays back the 
image from the HDMI source.
■
 One Touch Recording
Press
(REC while you are viewing a broadcast received with the AQUOS 
LINK-compatible recorder. The AQUOS LINK automatically recognizes the 
connected HDMI device and starts recording.
■
 Single remote control
The AQUOS LINK automatically recognizes the connected HDMI device and 
you can control the TV and the devices as if using a universal remote control.
■
 Control the AQUOS LINK-compatible audio system
Set the volume of AQUOS LINK-compatible audio system.
•  The above description is an example of the AQUOS LINK function.
•  The steps in “AQUOS LINK Setup” on page 62 need to be completed beforehand.
•  Refer to this operation manual and the operation manual of the AQUOS LINK device 
to be used with this TV.
-$@$6@6@&JOEC


-$@$6@6@&JOEC








 
						

							62
AQUOS LINK Setup
Menu
System Options
AQUOS LINK Setup
System
Options
AQUOS LINK Control
[On]Auto Power On[Yes]
[Auto]
Selecting Recorder
Channel Select Key
Audio Return Channel
Example
1   Press MENU to display the MENU screen, and then 
press
c/
d to select "System Options".
2   Press 
a/
b to select “AQUOS LINK Setup”, and 
then press ENTER.
3   Press 
a/
b to select a specifi c item, and then press 
ENTER.
4   Press 
a/
b (or 
c/
d ) to select the desired setting, 
and then press ENTER.
5   Press MENU to exit.
AQUOS LINK Control
Select AQUOS LINK Control to disable AQUOS LINK 
function even when an AQUOS LINK-compatible HDMI 
device is connected to the TV. This function prevents 
the device from starting to operate unexpectedly.
On:  You can operate AQUOS LINK-compatible 
equipment.
Off:  AQUOS LINK function does not work.
Auto Power On
If this is activated, the One Touch Play function is 
enabled.
Yes: While the TV is in standby mode, it automatically 
turns on and plays back the image from the HDMI 
source.
No: This function does not work.
Selecting Recorder
When multiple AQUOS LINK-compatible devices are 
connected, this function allows you to set the recorder 
for recording when you press 
(REC on the TV’s 
remote control unit.
Press
a/
b to select the recorder for recording.
Using AQUOS LINK
Channel Select Key
This function can be set for each input terminal.
On:The remote control unit of the TV can be used to 
select the channel, display program information, and 
perform other operations of the connected AQUOS 
LINK-compatible equipment.
Off:This function does not work.
Audio Return Channel
This function allows you to listen to the TV audio via 
audio equipment without using an optical fi ber cable, 
which conventionally is required.
Requirements for using an ARC-compatible AV 
amplifi er:
•  ARC-compatible AV amplifi er connected to the ARC-
compatible HDMI terminal (HDMI 1).
(Refer to the operation manual of the ARC-compatible 
equipment for details.)
•  Use of an ARC-compatible cable.
Auto:You can listen to the TV audio with ARC-
compatible audio equipment.
Off: This function does not work.
•  If the TV audio cannot be output from the AV amplifi er even 
after making the necessary settings, connect the TV to the 
AV amplifi er with an optical fi ber cable and select “Off”.
One Touch Playback
AQUOS LINK allows you to operate the HDMI-
connected equipment with one remote control.
Press
d to start playing back a title.
•  The last played program is played back. You can use the 
following buttons during broadcast viewing.
Buttons Description
POWER
(SOURCE)Turns the power of the HDMI connected devices 
on and off.
*Hold down to go in reverse.
,Starts playback.
-Hold down to fast forward.
+Playback stops.
)Sets pauses and still pictures.
7Pressing quickly once takes you to the start of the 
chapter currently playing. Each time you press it, 
you move back to the start of the previous chapter.
8Pressing quickly once takes you to the start of the 
next chapter. Each time you press it, you move 
ahead to the start of the next chapter.
• The buttons 7/8 do not function with the following 
Blu-ray disc players currently available.
- BD-HP20U, BD-HP50U
-$@$6@6@&JOEC


-$@$6@6@&JOEC








 
						

							63
Link Operation Menu
Recorder Power On/Off
Device Operation panel
[By AQUOS SP]
Play from Rec. List
Show Start Menu
Change Media of Device
Link Booking (Rec. Book)
Change Audio Output Device
Change Surround Mode
HDMI Device Selection
AQUOS LINK Setup Link Operation
MenuLink
Operation
Start Recording
Stop Recording Link Operation
MenuLink
Operation
The Link Operation Menu allows you to make 
adjustments during operation of AQUOS LINK-
compatible equipment.
1   Press OPTION to display the Link Operation Menu.
2   Press a
/
b to select the desired item, and then 
pressENTER.
•  Specifi c operations differ depending on the item you 
select. Following are the basic operations for each item.
Using AQUOS LINK
One Touch Recording
This function allows easy one-touch recording of the 
program being viewed on the TV to AQUOS LINK-
compatible equipment with a recording function by 
simply pressing 
(REC on the remote control.
Prepare the connected AQUOS LINK-compatible 
recorder for recording. Check the following items.
•  Make sure that the antenna cable is connected.
•  Check that there is suffi cient available space on the 
recording media (HDD, DVD, etc.).
•  On the TV, use “AQUOS LINK Setup” and “Selecting 
Recorder” to select the equipment for recording.
•  By default, the recorder connected to HDMI 1 is selected 
for recording.
1 Press (REC to start recording.
•  When you are viewing a broadcast received with the 
AQUOS LINK-compatible recorder selected in "Selecting 
Recorder", recording to the AQUOS recorder of the 
broadcast being viewed starts.
•  When you are viewing a broadcast received with 
equipment other than the AQUOS LINK-compatible 
recorder selected in "Selecting Recorder" or other 
external input equipment, pressing 
(REC on the remote 
control does not start recording.
2  Use the Link Operation Menu to stop recording.
1PressOPTION to display the Link Operation 
Menu screen.
2Pressa
/
b to select “Stop Recording”, and 
then press ENTER.
Start/Stop Recording
You can also use the Link Operation Menu for 
recording on the connected AQUOS LINK-compatible 
equipment.
1 Press OPTION to display the Link Operation Menu 
screen.
2  Select “Start Recording”, and then press ENTER to 
start recording.
•  You can also start recording by pressing (REC on the 
remote control unit.
3  Select “Stop Recording”, and then press ENTER to 
stop recording.
-$@$6@6@&JOEC


-$@$6@6@&JOEC








 
						

							64
Recorder Power On/Off
You can manually turn on/off the power of the 
connected AQUOS LINK-compatible equipment.
Each time you press ENTER, the connected 
equipment switches on or off.
Device Operation Panel
You can use the device operation panel to control 
playback operations.
Pressa
/
b/c
/d
 to select the desired operation.
•  This function works only when AQUOS LINK-compatible 
equipment with the Device Operation Panel function is 
connected.
Play from Rec. List
This function allows you to display the title list for the 
connected equipment and to play back the title you 
want to enjoy.
Before using this function.
Power on the AQUOS LINK-compatible equipment, 
and select the appropriate external input.
Select the title with a
/
b/c
/d
, and then press d
 to 
start playback.
•  This function works only when AQUOS LINK-compatible 
equipment is connected.
Show Start Menu
You can call up a setup menu from the connected 
AQUOS LINK-compatible equipment.
•  Depending on the status of the equipment (recording or in 
standby mode, etc), the setup menu will not be displayed.
•  The setup menu will not be displayed with the player BD-
HP20U currently available.
Change Media of Device
You can switch the media (HDD or DVD) for playback 
or recording on the AQUOS LINK-compatible recorder.
•  The Media type toggles each time you press ENTER in 
"Change Media of Device".
Using AQUOS LINK
Link Booking (Rec. Book)
You can call up the AQUOS LINK-compatible 
recorder's EPG and preset timer recordings using the 
TV's remote control.
Select the program on the recorder's EPG.
•  You can use a
/
b/c
/d
,ENTER,RETURN,EXIT and the 
colored buttons.
•  This function works only when an AQUOS LINK-compatible 
recorder is connected.
•  Refer to the operation manual of the recorder for details.
Change Audio Output Device
You can select to listen to the TV sound only from the 
AQUOS LINK-compatible audio system.
By AQUOS audio SP: The sound from the TV speaker is 
muted and only the sound from the AQUOS LINK-
compatible audio system is audible.
• You can use VOL+/- and MUTE.
By AQUOS SP: The sound is output from the TV 
speaker.
Change Surround Mode
You can manually change the AQUOS AUDIO speaker 
system's sound mode.
The sound mode changes each time you press 
ENTER.
•  Refer to the operation manual of the AQUOS LINK-
compatible audio system for details.
HDMI Device Selection
If multiple HDMI devices are connected in a daisy 
chain, you can specify which device to control here.
Pressa
/
b to select the desired device from a list of 
connected HDMI devices, and then press ENTER.
AQUOS Link Setup
You can also display the AQUOS LINK Setup screen 
from the Link Operation Menu.
-$@$6@6@&@JOEE


-$@$6@6@&@JOEE








 
						

							65
Using AQUOS LINK
Using a Smartphone with the TV
This function enables you to connect the TV to a smartphone that supports Mobile High-Defi nition Link (MHL) 
using an MHL-compatible cable.
To connect the TV to your MHL-compatible smartphone, be sure to use an MHL-compatible cable (commercially 
available).
•  You can view pictures and video on a large screen.
•  You can play back music fi les.
MHL-compatible cable
Back panel vertical inputs
•  An MHL-compatible portable device is required to use this function. Connect the device to the HDMI 4 terminal.
■ Auto Power On
When an MHL-compatible device is connected to the TV, the TV turns on 
automatically.
•  This function operates when "AQUOS LINK Control" is set to "On". (See page 62.)
■ Auto Input Selection
When an MHL-compatible device is connected while the TV is on, the input 
mode is selected automatically.
•  This function operates when "AQUOS LINK Control" is set to "On". (See page 62.)
■ Operation Using the Remote Control
The remote control of the TV can be used to operate a portable device.
•
a/
b/
c/
d,ENTER,EXIT,0-9,•(DOT),ENT, etc.
•  The operations vary depending on the connected equipment and content being 
viewed.
-$@$6@6@&@JOEE


-$@$6@6@&@JOEE








 
						

							66
VIEW MODE
You can select the screen size.
1   Press VIEW MODE.
•  The View Mode menu displays.
•  The menu lists the View Mode options selectable for the type of video signal currently 
being received.
2   Press VIEW MODE or 
a/
b while the View Mode menu is displayed to select a 
desired item on the menu.
•  You can sequentially select a View Mode that has its own aspect ratio.
•  Connect the PC before making adjustments. (See page 18.)
•  Selectable screen size may vary with input signal type.
•  You can have the same settings by choosing "View Mode" on the menu items. (See page 33.)•  You may not be able to change the View Mode while in 3D mode.
Example: Screen size images
Input signalNormal Zoom Stretch Dot by Dot
4:3Keeps the original 
aspect ratio in a full 
screen display.For viewing 
widescreen
programs. The top 
and bottom of the 
image is cropped.An image fully fi lls the 
screen.Detects the resolution 
of the signal and 
displays an image with 
the same number of 
pixels on the screen.
Input signalStretch Dot by Dot
16:9An image fully fi lls the 
screen.Detects the resolution 
of the signal and 
displays an image with 
the same number of 
pixels on the screen.
Using a PC
Displaying a PC Image on the Screen
-$@$6@6@&JOEC


-$@$6@6@&JOEC








 
						

							67
Using a PC
Example
Menu
View Option
Terminal Setting AQUOS LINK Setup
3D Setup
Menu Design
OtiLkOt System Options
System
Options
1   Press MENUto display the MENU screen, and then 
press
c/
d to select "System Options".
2   Press a
/
b to select "Terminal Setting", and then 
pressENTER.
3   Press 
a/
b to select "PC input" or "Audio Select", 
and then press ENTER.
4   Press 
a/
b to select a specifi c adjustment item, 
and then press ENTERto set each item.
5   Press 
a/
b (or 
c/
d) to select or adjust the desired 
setting, and then press ENTER.
Adjusting the PC Image
Auto Sync. (for Analog PC Input Mode Only)
For automatically adjusting the PC image.
Yes:Auto Sync. starts and "Now adjusting the image." 
displays.
No:This function does not work.
•  When "Auto Sync." is successful, "Completed" displays. If 
not, "Auto Sync." failed.
•  "Auto Sync." may fail even if "Completed" displays.
•  "Auto Sync." may fail if the computer image has low 
resolution, has unclear (black) edges, or is moved while 
executing "Auto Sync.".
•  Be sure to connect the PC to the TV and switch it on before 
starting "Auto Sync.".
Fine Sync.
Ordinarily you can easily adjust the picture as necessary 
to change image position using "Auto Sync.". In some 
cases, however, manual adjustment is needed to 
optimize the image.
H-Pos.:Centers the image by moving it to the left or right.
V-Pos.:Centers the image by moving it up or down.
Clock:Adjust when the image fl ickers with vertical 
stripes.
Phase:Adjust when characters have low contrast or 
when the image fl ickers.
•  For resetting all "Fine Sync." adjustment items to the factory 
preset values, press 
a/
b to select "Reset", and then press 
ENTER.
•  It is not necessary to adjust the "Clock" or "Phase" when a 
digital signal is being input, so it cannot be selected.
•  The default cursor position may not be in the center, 
because the screen position variable ranges may be 
asymmetrical.
•  The screen position variable ranges depend on the View 
Mode or the signal type. The ranges can be seen on the 
position-setting screen.
Setting Audio Input
Audio Select
This function sets the terminal to output the computer 
audio.
The adjustment items vary depending on the input 
source. Select the input source corresponding to the 
terminal connected to the PC and then adjust the 
desired item.
■ PC IN
Video:Select this when the TV and PC are connected 
using an analog RGB cable and the audio is not input.
Video+Audio:Select this when the TV and PC are 
connected using an analog RGB cable and the audio is 
input via a Ø 3.5 mm stereo minijack.
■ HDMI 2HDMI(Digital):Select this when the TV and PC are 
connected using an HDMI-certifi ed cable and audio is 
input via the same cable.
HDMI+Analog:Select this when the TV and PC are 
connected using a DVI-HDMI conversion cable and the 
audio is input via a Ø 3.5 mm stereo minijack.
•  When "Audio Select" is set to "HDMI(Digital)", sound will 
not be produced if you use only an HDMI-certifi ed cable to 
connect HDMI-compatible equipment. To produce sound, 
you should make an analog audio connection.
•  If you want to connect HDMI-compatible equipment 
using only an HDMI-certifi ed cable, set "Audio Select" to 
"HDMI(Digital)".
PC Compatibility Chart
It is necessary to set the PC correctly to display XGA 
and WXGA signal. 
VGA and XGA are registered trademarks of International 
Business Machines Corp.
31.5 kHz
31.5 kHz
37.9 kHz
37.5 kHz
35.1 kHz
37.9 kHz
48.1 kHz
46.9 kHz
48.4 kHz
56.5 kHz
60.0 kHz
47.7 kHz 640 x 480 720 x 400
VGA
800 x 600 SVGA
XGA 1024 x 768
WXGA 1360 x 76870 Hz
60 Hz
72 Hz
75 Hz
56 Hz
60 Hz
72 Hz
75 Hz
60 Hz
70 Hz
75 Hz
60 HzO
O
O
O
O
O
O
O O
O
O
64.0 kHz SXGA 1280 x 1024 60 Hz O
65.3 kHz SXGA+ 1400 x 1050 60 Hz O
75.0 kHz UXGA 1600 x 1200
60 Hz
67.5 kHz 1080p 1920 x 1080 60 HzO
Horizontal
FrequencyVESA
Standard ResolutionVertical
Frequency
-$@$6@6@&JOEC


-$@$6@6@&JOEC








 
						

							68
•  The TV can be controlled from a PC, control panels 
and other devices using the RS-232C or IP.
•  Use a cross-type RS-232C cable, ETHERNET cable 
(commercially available) or wireless LAN for the 
connections.
•  This operation system should be used by a person who is 
accustomed to using computers.
AQUOS Remote Control
Example
Menu
EZ Setup
Internet Setup
Language
DivX®Setup Broadcasting Setup Initial SetupInitial
Setup[English]
1 Press MENU to display the MENU screen, and then 
press
c/
d to select "Initial Setup".
2 Press a
/
b to select "Internet Setup", and then 
pressENTER.
3 Press a
/
b to select "AQUOS Remote Control", 
and then press ENTER.
■ AQUOS Remote ControlSet this when operating the TV from equipment 
connected by LAN or wireless LAN.
•  When "AQUOS Remote Control" is selected, "Change" will 
be highlighted. Press ENTER.
Enable:Allows operation from the connected equipment.
Disable:This function does not work.
■ Select Device NamesSet the name of the TV displayed on the portable 
device.
•  Use the software keyboard to set the name. See page 73 
for details on the software keyboard.
■ Detailed SettingsMake the detailed settings (Login ID, password, etc.).
Follow the on-screen instructions to confi gure the 
settings.
Control of the TV
Using a PC
Communication Conditions for IP
Connect to the TV with the following settings made for 
IP on the PC.
IP protocol:TCP/IP
Host IP address:Set the IP address on the TV menu
Service:None (Do not select Telnet or SSH)
TCP port#:Set a port number on the TV menu 
(Control port)
When you set your ID and password on the TV menu, 
you need to enter them as soon as you connect to the 
TV.
•  When you use this function, make settings for "AQUOS 
Remote Control".
•  The connection will be cut off when there has been no 
communication for 3 minutes.
Communication Conditions for RS-232C
Set the RS-232C communication settings on the PC to 
match the TV's communication conditions.
The TV's communication settings are as follows:
Baud rate:9,600 bps
Data length:8 bits
Parity bit:None
Stop bit:1 bit
Flow control:None
■ Communication procedure Send the control commands from the PC via the RS-
232C or IP.
The TV operates according to the received command 
and sends a response message to the PC.
Do not send multiple commands at the same time. 
Wait until the PC receives the OK response before 
sending the next command.
■ Command format
Eight ASCII codes 
eCR
Command 4-digits
Parameter 4-digitsReturn code
C1 C2 C3 C4 P1  P2  P3  P4
Command 4-digits: Command. The text of four characters.
Parameter 4-digits: Parameter 0–9, x, blank, ?
■ ParameterInput the parameter values, aligning left, and fi ll with 
blank(s) for the remainder. (Be sure that 4 values are 
input for the parameter.)
When the input parameter is not within an adjustable 
range, “ERR” returns. (Refer to “Response code format”.)
Any numerical value can replace the “x” on the table.
a30 0009 0???? ?
When “?” is input for some 
commands, the 
present setting 
value responds.
■ Response code format
Normal response
Return code (0DH)
Return code (0DH) Problem response (communication 
error or incorrect command)
OKERR
-$@$6@6@&@JOEE


-$@$6@6@&@JOEE