Sharp Lc 60le925 Operation Manual

 9
Using the Remote Control Unit
Use the remote control unit by pointing it towards the 
remote control sensor on the TV. Objects between the 
remote control unit and the remote control sensor may 
prevent proper operation.
30º 30º30º
30º
17´ (5 m)Remote control sensor
■ Cautions regarding the remote control unit
 Do not expose the remote control unit to shock. In addition, 
do not expose the remote control unit to liquids, and do not 
place in an area with high humidity.
 Do not install or place the...

 10
Antennas
To enjoy a clearer picture, use an outdoor antenna. The following is a brief explanation of the types of connections 
that are used for a coaxial cable. If your outdoor antenna uses a 75-ohm coaxial cable with an F-type connector, 
plug it into the antenna terminal at the rear of the TV set. For connecting the antenna cable to the TV, use 
commercially available cables.
300-ohm twin-lead cable 75-ohm coaxial cable (round)
75-ohm coaxial cableIN OUT
300-ohm 
twin-lead cable VHFANTENNAUHF...

 11
Part Names
TV (Front)
*1 OPC: Optical Picture Control
*2 See pages 18 and 24 for using the touch sensor panel.Center Icon illumination
(See page 32.)
Infrared emitter (See page 43.)
POWER  *2 INPUT VOL
l/
k
MENURemote control sensor
OPC sensor *1
(See page 26.)
CH
V/
U
TV (Rear)
RS-232C terminal
Antenna/Cable in
COMPONENT terminalsDIGITAL AUDIO OUTPUT terminal HDMI 3 terminal
HDMI 4 terminal HDMI 1 terminal
ARC:  Audio Return Channel
  (See pages 54 and 55.) PC IN terminal
AUDIO IN terminal 
(shared...

 12
1
18
19
20
21 4 3 2
5
23
24 8 7 6
9
25
26
28
29 15 14 13 12 11 10
16
1727 22
1 POWER: Switch the TV power on or enter standby. (See 
page 18.)
2 TV, STB, DVD•VCR, AUDIO: Switches the remote 
control for TV, STB, DVD, BD, VCR and AUDIO operation. 
(See pages 52 to 53 for details.)
  * To enter the code registration mode, you need to press 
an appropriate button (STB, DVD•VCR or AUDIO) and 
DISPLAY at the same time.
3 External equipment operational buttons: Operate the 
external equipment.
4 OPTION:...

 13
Introduction to Connections
Experiencing HD Images
An HDTV without an HD source is just an ordinary TV.
To enjoy HD images on the TV, you should get HD programming from the following:
Over-the-air broadcasting via HD quality antenna
HD cable/satellite subscription
HD compatible external equipment
For information on updating to HD programming, ask your cable/satellite service provider.
Types of Connection
Image quality differs depending on the terminal used. To enjoy clearer images, check the output...

 14
Connecting to External Equipment
You can connect many types of external equipment to your TV. To view external source images, select the input 
source from INPUT on the remote control unit or on the TV. (See pages 13 and 21.)
For connecting the TV to external equipment, use commercially available cables.
CAUTION
 To protect equipment, always turn off the TV before connecting any external equipment.
 Please read the relevant operation manual (Blu-ray disc player, etc.) carefully before making...

 15
Connecting to External Equipment
■ When using Component cable (COMPONENT):
Blu-ray disc player     DVD player
COMPONENT OUT
Back panel
horizontal inputs
AUDIO-R (Red)
AUDIO-L (White)
Y (Green)PB (Blue) P
R (Red) Audio cable
Component video cable
 To enjoy 1080p display capability, connect your external equipment using an HDMI-certi ed cable or a component cable and 
set the equipment to 1080p output.
 See page 14 for connecting a Blu-ray disc player, DVD player or an HD cable/satellite set-top box to...

16
Connecting to External Equipment
Connecting an Audio Amplifi er
■ When using optical fi
 ber cable:
It is possible to output audio through the DIGITAL AUDIO OUTPUT terminal\
. (See page 31 for details.) PCM audio 
outputs from the terminal.
DIGITAL AUDIO INPUTOPTICAL
Back panel 
vertical inputs
Optical fiber cable
•  Depending on the connected equipment, audio will not output from the DIG\
ITAL AUDIO OUTPUT terminal in HDMI  connection. In this case, set the audio formats of the connected equipme\
nt to...

 17
Connecting a PC
Refer to page 59 for a list of PC signals compatible with the TV.
■ When using HDMI cable (HDMI 1, 2, 3 or 4):
HDMI OUT
Back panel 
vertical inputs
HDMI-certied cable
 Depending on the board, only video signals may be output. In this case, in addition to connecting an HDMI-certi ed cable 
to the HDMI 1 terminal, connect a Ø 3.5 mm stereo minijack cable to the AUDIO IN terminal and set Audio Select to 
HDMI+Analog. (See page 59.)

The HDMI terminals only support digital signal.
■ When...

 18
Turning On/Off the Power
POWER
POWER (On/Standby)
Press POWER on the TV or on the remote control unit 
to turn the power on.
 The Initial Installation starts when the TV powers on for the 
 rst time. If the TV has been turned on before, the Initial 
Installation will not be invoked. For changing the settings of 
the Initial Installation, perform EZ setup on the Initial Setup 
menu on page 33.
Press POWER on the TV or on the remote control unit 
again to turn the power off.
 The TV enters standby and...