Sharp Lc 46hd1e Operation Manual

							
Watching DVB broadcasts
Software update
TV base software and DVB software
To ensure that your TV set is always up to date, from 
time to time SHARP will make updated TV base 
software and DVB software versions available. These 
updates are broadcast via satellite (only via ASTRA1).
•  This function is not available in some countries.
Automatic search for new software via satellite
The set automatically determines whether a new 
software version is available via satellite during the night 
when the EPG data are updated. However the TV set 
must remain in standby mode for this (do not switch off 
the set with the power switch).
If a new software version has been found, the set 
informs you with an on-screen message the next time 
it is switched on (see right column – “Loading new 
software”).
Manual search for new software via satellite
If it is not automatically displayed that a new software is 
available when switching on the set, you can also run a 
manual search. 
The system first checks whether a software update is 
available via satellite.Press  MENU  and the TV menu screen displays.
Press  c/d  to select “Setup”, and then press  b 
to move down.
Press  c/d  to select “Miscellaneous”, and then 
press  b to move down.
Press  c/d  to select “Software update”, and 
then press  OK.
•  The software versions currently loaded in the set are 
listed.
Software update -> Software type
TV base software
DVB software
Press  a/b  to select the desired option, and 
then press  OK to start the search.
•  If new versions are available then a subsequent 
screen message will be displayed.
1
2
3
4
5
Loading new software
The following will appear if a new software is found via  
the search.
Software update -> Update options
Load new software now
Load new software after switch off to standby
Keep current software
Proceed to the next steps by following the 
screen prompts.
•  A bar is displayed to inform you of the progress of the load process. During the loading process do not 
switch off your device via the power switch! This may 
last up to 20 minutes. You will be informed when it is 
finished.
At the end of loading: 
Turn off the TV set off with the power switch, 
unplug the AC cord, and turn it on again. 
•  If a new software has not been updated via satellite, you will be reminded of this several times after 
switching on the set.
6
7
 29
LC -5 2H D1E -g b.i n dd   2 9LC-52HD1E-gb.indd   292008/0 3/2 4   1 5:0 1:1 82008/03/24   15:01:18
 
						

							
Watching DVB broadcasts
Radio mode
You can only receive radio stations via DVB.
If you do not have DVB radio reception then you can 
play audio from an external device via the TV set using 
the audio/AV inputs.
 Press RADIO to activate the DVB radio mode.
18:00 - 18:10  Nachrichten Radio: Stereo
EXT6
EXT5
•  An overview of the radio stations displays.
• Press  RADIO again to exit the DVB radio mode.
Switching the screen off and play the radio only
 Press  RED to switch the screen off.
  To switch on the screen, press  RED again.
•  You can still change channels with  Pr /s  or  0 - 9  
on the remote control with the screen turned off.
Using the Radio menu and EPG
Just like in normal TV mode, with the radio menu you 
can set the sound, search for and store radio stations 
(automatically or manually), change stations and set 
switch-off/alarm functions. You can also call up the 
EPG screen for radio stations.
Press  RADIO  to activate the DVB radio mode.
Press  MENU  to display the radio menu screen.
1
2
 30
LC -5 2H D1E -g b.i n dd   3 0LC-52HD1E-gb.indd   302008/0 3/2 4   1 5:0 1:1 92008/03/24   15:01:19
 
						

							
Info display and index feature
We have designed the TV with integrated content-
based information text for each item so that you do not 
have to worry about reading the operation manual each 
time. In conjunction with the index feature, this makes 
a convenient control system.
Using info text
Press INFO with the menu screen active.•  You can see info text only when INFO icon is shown 
on the lower right corner of the screen.
ENDINFO
Setup Εxtended functions Picture Sound Recording
TV menu
AQUOS LINK setup
Stations
Child lock
Timer functions
Language
Miscellaneous
Here, you can search for stations automatically or manually as well as s\
et the menu
language, timer functions, parental lock, on-screen displays, etc. Setup
1
Using Index
Using Index, you can start all wizards and many 
operating functions directly from a single point. The 
complete functional scope of the TV set can thus be 
easily understood.
Alphabetic sorting is preceded by the items 
“Language”, “Integrated features” and “Repeat initial 
installation”. Press  INFO with no other menu screen active.
If “OK” appears in the highlighted line, this 
function can be accessed directly with  OK.
 -zaEND
Index
Language
Integrated features
Repeat initial installation
AV (Audio/Video)
AV equipment
Decoder Camcorder
Activate Previous/next letter Page
Select letter
In the "TV Menu->Setup->Language" menu you can select your language for
operating the TV set.
E Selecting keywords in the Index screen
There are 3 ways to navigate from item to item in the 
index screen.
1
 Select initial letters with  0 - 9 on the remote control 
like with a mobile phone keypad.
2  Press  c/d  to go to the preceding/next letters, or 
press  a/b  to go from line to line.
3  Press  Pr /s  to scroll the page up/down.
1
2
Menu operation
 31
LC -5 2H D1E -g b.i n dd   3 1LC-52HD1E-gb.indd   312008/0 3/2 4   1 5:0 1:2 02008/03/24   15:01:20
 
						

							
Sound menu
Various sound-related settings can be optimised.
Sound
TV menu
DYNAMIC
Treble
Bass
Loudness
Dolby Virtual Speaker
Auto volume 0
0
off
on
off
off
Balance 0
AV output signal Sound 1+2
Headphone volume 50
Switch on volume 30
Volume adjustment for current station 0
ResetRecording Connections Setup Εxtend
✔
 Sound menu items
Items
Treble*
Bass*
Loudness
Dolby Virtual Speaker (See page 33 for its functions.)
Auto volume
Balance
Loudspeaker sound
AV output signal
Headphone volume
Switch on volume
Volume adjustment for current station
Reset
NOTE
•  Items with * can be adjusted and reset for each individual  AV mode.
•  Some items do not appear depending on the type of  received signal.
• Press  a/b  to select “more...”, if the item you want to 
adjust is not displayed.
Menu operation
Picture menu
Various picture-related settings can be optimised.
Picture Sound Recording
TV menu
AV mode Standard
Contrast
Brightness
Colour
Sharpness
Colour temperature 18
10
10
1
medium
DNR high
Auto format off off
Picture quality enhancement on
100Hz off Film mode
Optical power control (OPC) off
ResetSetuConnections
Press  MENU  and the TV menu screen displays.
Press  c/d  to select “Picture”, and then press 
a /b  to select a desired item.
Press  c/d  to set/adjust. When you exit the 
menu the change is adopted.
✔  Picture menu items
Items
AV mode
Contrast*
Brightness*
Colour*
Tint*
Sharpness*
Colour temperature*
Colour standard
DNR
Move picture up/down
Auto format
Film mode
Picture quality enhancement
100Hz
Optical power control (OPC)
Reset
NOTE
•  Items with * can be adjusted and reset for each individual  AV mode.
•  Some items do not appear depending on the type of  received signal.
• Press  a/b  to select “more...”, if the item you want to 
adjust is not displayed.
•  100Hz will have no effect in the following cases.
  1) The type of signal received is a PC signal.
  2) An OSD is being displayed.
  3) Teletext is activated.
1
2
3
AV mode
AV mode gives you five viewing options to choose from 
to best match the system environment, which can vary 
due to factors like room brightness, type of programme 
watched or the type of image input from external 
equipment.
Item
Standard : For a highly defined image in a normally bright 
room (Enhanced Picture Contrast: On)
Soft : Creates a softer image. (Enhanced Picture Contrast: 
On)
Eco : Reduces power consumption. (Enhanced Picture 
Contrast: Off)
Dynamic : For a clear-cut image emphasising high 
contrast for sports viewing. (Enhanced Picture Contrast: 
On)
User : Allows the user to customise settings as desired. 
You can set the mode for each external source. 
(Enhanced Picture Contrast: Off)
NOTE
•  You can adjust the factory presets given in “Standard”,  “Soft”, “Eco” and “Dynamic”.
•  You can assign different AV mode to each external source.
•  Enhanced Picture Contrast technology detects the source  video characteristics and smoothly adjusts the screen 
brightness accordingly, enabling deeper black levels.
•  Enhanced Picture Contrast is activated when you turn  the OPC function off for the items “Standard”, “Soft” and 
“Dynamic” in AV mode.
 32
LC -5 2H D1E -g b.i n dd   3 2LC-52HD1E-gb.indd   322008/0 3/2 4   1 5:0 1:2 12008/03/24   15:01:21
 
						

							
Recording menu
You can set timer programmed recordings with the 
integrated HDD Digital Recorder or other connected 
recording devices. Further information on HDD 
recording is provided in the chapter “HDD Digital 
Recorder operation ”.
•  The internal HDD DIGITAL Recorder cannot record signals 
from the following terminals: EXT 3 (COMPONENT input), 
EXT 5, 6 (HDMI input), and EXT 7 (PC input).
Recording
TV menu
Recording wizard
Timer list
Pre-record time
Post-record time 00 min
05 minSetup Εxtended functionConnections
✔
 Recording menu items
Items
Recording wizard Via EPG
Via teletext (VPS)
Manual
Timer list
Pre-record time
Post-record time
Recording wizard
To record TV programmes, you can use the data from 
EPG, teletext or enter the data manually.
E Via  EPG
Press  MENU  and the TV menu screen displays.
Press  c/d  to select “Recording”, and then 
press  OK.
Press  a/b  to select “Recording wizard”, and 
then press  OK.
Press  a/b  to select “Via EPG”, and then press 
OK .1
2
3
4
Menu operation
Dolby Virtual Speaker
The Dolby Virtual Speaker effect simulates a surround 
sound environment with only two speakers. You can 
choose between two different settings for the width of 
the generated sound characteristics.
Item
off : No effect
Reference Mode : Creates a convincing five-speaker 
surround sound listening experience from just two 
speakers. In this mode, the apparent width of the 
sound across the front image is defined by the distance 
between the two speakers.
Wide Mode : Provides a wider, more spacious front audio 
image from two speakers placed close together, with 
the same realistic five-speaker surround sound as 
Reference mode.
15:57-16:59 arte    Charmed - Zauberhafte Hexen
16:00-16:15 MDR FERN...   Hier ab vier
16:00-16:10  EinsExtra   EinsExtra Aktuell
16:00-17:15 SAT.1   Richter Hold
16:00-16:30 ProSieben   M. Asam - Mode
16:00-16:55  ZDFtheater...   Waschtag
16:05-17:00  Bayrische...   Wir in Bayern
16:05-16:45 KiKa   Skippy, der Buschpilot
16:05-17:00 KABEL1   Star Trek - Das nächste Jah... EPG (Electronic Programme Guide) Mon 31.07./16:05
Date
Time
Stations
Topics Mon 31.07
Now
all
all Tue 01.08
Wed 02.08 Thu 03.08 Fri 04.08
•  The EPG screen displays.
•  You may be routed to the “Time and date” entry 
screen if the TV does not recognise the current time.
Press  a/b /c /d  to select the programme you 
want to record, and then press  RED.
•  Select a programme that has not yet started.
•  A message appears if there is a conflict between two 
programmes. Follow the screen prompts and choose 
the one that has priority.
The timer list screen appears, outlining each 
setting used for the upcoming recording. 
Confirm with  OK. You can make adjustments 
as explained in step 3 in the following  Manual 
section.
Once completed, a red dot will appear in front 
of the programme as identification.
•  To cancel the recording, select a title from the list 
and press  RED. If the timer list has already been 
transferred to an external recorder, then the timer 
must also be deleted there.
E Via teletext (VPS)
Select “Via teletext (VPS)” instead of “Via EPG” 
in step 4 in  Via EPG.
•  The station selection screen displays.
•  You may be routed to the “Time and date” entry 
screen if the TV does not recognise the current time.
Press  a/b /c /d  to select the station you want 
to record from, and then press  OK.
Press  a/b  to select the programme you want 
to record, and then press  OK.
•  Select a programme that has not yet started.
•  A message appears if there is a conflict between two 
programmes. Follow the screen prompts and choose 
the one that has priority.
Timer list screen appears, outlining each setting 
used for the upcoming recording. Confirm with 
OK . You can make adjustments as explained in 
step 3 in the following  Manual section.
NOTE
•  Select the teletext start page according to the station (the 
default setting is “301”).
  For the selection method, follow these steps: 1  while in the teletext mode, press  MENU to display the 
Teletext menu
2  select “Setup”
3  press  OK on the remote control
4  select “Preview pages”, and then input the selection 
value
5
6
7
1
2
3
4
 33
L C -5 2H D1E -g b.i n dd   3 3LC-52HD1E-gb.indd   332008/0 3/2 4   1 5:0 1:2 32008/03/24   15:01:23
 
						

							
E Manual
You may enter the necessary information for recording 
manually.Select “Manual” instead of “Via EPG” in step 4 
in Via EPG .
•  The station selection screen displays.
•  You may be routed to the “Time and date” entry 
screen if the TV does not recognise the current time.
Press  a/b /c /d  to select the station you want 
to record from, and then press  OK.
Timer list screen appears, outlining each setting 
used for the upcoming recording. Set the 
following settings as necessary. Confirm with 
OK .
1 Recorder: Selection of the recording device.
2  Date: Date of recording
3  Recording time: Time of recording
4  VPS: Selection of using VPS signal
5  Recording type: Selection of recording frequency 
(once only, Mon-Fri, daily, weekly or serial [if EPG 
data is available]).
•  A message appears if there is a conflict between two  programmes. Follow the screen prompts and choose 
the one that has priority.
NOTE
•  If you use an external recorder without AV Link, you have to  select the recording source in the recorder (e.g. AUX, refer 
to your recorder’s operation manual). In case of recording 
DVB programmes, the TV’s tuner is used, not the VCR’s 
tuner.
•  If you use an external recorder with AV Link, this recording  source selection is controlled automatically.
Timer list
Here you will find a list of channels already 
programmed for recording. From here, you can 
also change the recording data  (GREEN), delete 
programmed recordings completely  (YELLOW), or 
programme a new recording  (RED) by pressing the 
assigned colour buttons.
Pre- and post record time
If you record a programme without VPS, you can 
specify a time span by which your programme 
time should be brought forward/prolonged so that 
programmes which begin/end too early/late are 
recorded from start to finish.
1
2
3
Menu operation
Timer recording with external 
devices
E Recorder with AV Link
If you use an externally connected recorder with AV 
Link or a similar system, the TV set and connected 
recorder exchange its own station/timer data.
Please consult the operating manual of your recorder 
to find out if your recorder is AV Link compatible. 
In addition use only Euro SCART cables for the 
connection between the TV set and recorder.
Analogue stations
The timer data is transmitted automatically from the TV 
set to the recorder after programming is complete.
The recording is then controlled by the recorder 
and the recorder tuner is used for reception of the 
programme.
The recording data is not saved in the timer list of the 
TV set. Consequently if you want to change or delete 
the timer data then you must do so on the recorder.
Digital stations
If you want to record digital stations with an externally 
connected recorder, then the DVB tuner is used and 
the TV device takes over control of the recorder. Then 
the station on the TV set is locked during the timer 
recording.
E Recorder without AV Link
If you cannot programme your externally connected 
recorder from the TV set, but it supports AV Link, the 
receiver of the TV set is always used. 
AV Link must be switched on on the recorder. Read the 
operating instructions of your recorder.
In addition use only Euro SCART cables for the 
connection between the TV set and recorder.
Analogue and digital stations
You can control the recording from the TV set. The 
recorder must be set manually to the AV input to which 
the TV is connected. Then the station on the TV set is 
locked during the timer recording.
Copy protection
Copy-protected programs will not be output on the 
EURO SCART sockets for legal reasons.
 34
L C -5 2H D1E -g b.i n dd   3 4LC-52HD1E-gb.indd   342008/0 3/2 4   1 5:0 1:2 42008/03/24   15:01:24
 
						

							
Connections menu
Use this menu when connecting recorders, DVD 
recorder, etc. There is a wizard which will guide you 
through the individual steps.
TV menu
AV setup
Sound components
Antenna DVB
AV-Link
MiscellaneousSetup Εxtended functions Picture
Connections
✔
 Connections menu items
Items
AV setup Connection wizard
Sound components TV speakers
HiFi/AV amplifier
Antenna DVB Antenna DVB-T Antenna wizard
Antenna DVB-S Antenna wizard
AV-Link  Start transmission/Stop transmission
Miscellaneous Manual adjustment 
of AV standard
At EXT1/EXT2/EXT4
Assign digital audio input
Allow switching voltage
RGB insertion at EXT1
AV setup
The integrated Connection wizard shows you which 
terminal you should connect your equipment to. Then 
connect the equipment according to the diagram and 
follow the messages one after another.
A detailed step-by-step explanation is provided on 
page 16.
Antenna DVB
You can reconfigure the antenna setting after 
performing initial installation. Read the on-screen 
instructions carefully or see page 10 for each setting.
AV Link
With this function you can transfer the station data 
of the TV (such as station preset numbers/names/
channels/frequencies) to the recorder if the recorder is 
set up for AV Link.
Miscellaneous
Here you can change the AV standards, assign the 
digital audio input, switch the switching voltage on/off 
and allow RGB settings.
Menu operation
 35
L C -5 2H D1E -g b.i n dd   3 5LC-52HD1E-gb.indd   352008/0 3/2 4   1 5:0 1:2 42008/03/24   15:01:24
 
						

							
Menu operation
Setup menu
You can search for stations automatically or manually as well 
as set the menu language, timer functions, child lock, etc.
SetupΕxtended functions Picture Sound
TV menu
AQUOS LINK setup
Stations
Child lock
Timer functions
Language
Miscellaneous
Items
AQUOS LINK setup Auto power on
Recorder selection
Stations Search wizard
Change search 
settings
Start search/update
Manual tune
Change stations
Select/change favourites
PIP* Type*
Position*
Child lock PIN ???? Lock immediately
Lock daily
Age-related lock
Change PIN
Delete PIN
Timer functions Switch off today only
Switch off daily
One-time reminder
Wake up Mon-Fri
Wake up Sat
Wake up Sun
Wake up with
Wake up signal volume
Language
Miscellaneous Automatic switchoff if no signal
On-screen displays
On-screen display 
time
Volume
Time and date Time
Deviation from 
Universal Time
Date
Beginning of 
daylight-saving time
End of daylight-
saving time
Software update TV base software
DVB software
DVB subtitles
DVB character set
NOTE
*  This item appears only when PIP is activated.
Stations
The menu contains the automatic station search and 
the manual station settings. You can re-sort stations, 
enter and change station names, and delete stations.
E Search  wizard
Use this menu to search for stations automatically once 
certain settings have been made. (See page 10,  Initial 
installation wizard  for details.)
Press  MENU  and the TV menu screen displays.
Press  c/d  to select “Setup”, and then press 
OK .
 Press  a/b  to select “Stations”, and then press 
OK .
 Press  a/b  to select “Search wizard”, and then 
press  OK.
•  You will get a table for the auto station search.
If necessary select “Change search settings”, 
and then press  OK. Otherwise skip to step 6.
Press  a/b /c /d  to select your country or area 
listed on the screen, and then press  OK.
Follow the menus and make necessary settings 
one after another.
Press  a/b  to select “Start search/update”, and 
then press  OK.
NOTE
•  The station search may take some time. 
•  Do not make any entries or switch off the set during this 
time. 
•  When the search has ended you will be shown the found  and stored stations sorted in numerical order. 
•  After the station search has been completed, close the  table by pressing  OK.
1
2
3
4
5
6
 36
LC -5 2H D1E -g b.i n dd   3 6LC-52HD1E-gb.indd   362008/0 3/2 4   1 5:0 1:2 42008/03/24   15:01:24
 
						

							
Menu operation
E Manual  tune
Use the manual tune option when receiving TV signals 
whose TV/Colour standard deviate from the one 
specified. However, this requires detailed knowledge.
E Change  stations
You can move stations, enter or change station names, 
and delete stations. The operation is the same as 
explained on page 12, “To delete, restore, move, 
and rename stations from the station list ”.
E Select/change  favourites
Each favourites list can contain up to 99 stations. 
You can put together the favourites lists to suit your 
requirements (e.g. topic lists). Other persons using this 
TV set can create their own favourites lists. 
The favourites lists also have the advantage that the 
stations from different signal sources can be stored in 
the order of your preference.
Up to 6 favourites list can be stored.
Press  MENU  and the TV menu screen displays.
Press  c/d  to select “Setup”, and then press 
OK .
 Press  a/b  to select “Stations”, and then press 
OK .
 Press  a/b  to select “Select/change 
favourites”, and then press  OK.
All stationsStations of FavouriteList1Select/change favourites Search wizard Manual tune Change stations
Stations
•  “Select/change favourites” screen displays.
GREEN
: Select the next favourites list.
Renaming favourites 
Prerequisite : Favourites list (right column) must 
be selected. If not, change the list with  d.
Press  BLUE to activate the “Rename favourite 
list”, and enter the new name with  0 – 9 as on 
a mobile phone key pad, and then press  OK to 
save the new name.
1
2
1
2
Adding favourites
Prerequisite : The “All stations” screen (left 
column) must be selected. If not, change the list 
with  c.
Using  a/b  or  0 – 9,  mark the stations to be 
added as a new favourite.
Press  OK to add.
All stationsStations of FavouriteList1Select/change favourites Search wizard Manual tune Change stations
Stations
•  The new station is added at the end of the favourites 
list. Once you exit the screen, the change is adopted.
Deleting favourites
Prerequisite : The Favourites list (right column) 
must be selected. If not, change the list with  d.
Using  a/b  or  0 – 9 , mark the stations to be 
deleted.
Press  OK to delete.
 Or
 Press  RED to activate “Clear favourites list”, 
and then press  OK to clear the list.
Moving/sorting favourites Prerequisite : The Favourites list (right column) 
must be selected. If not, change the list with  d.
Using  a/b  or  0 – 9 , mark the stations to be 
moved.
Press  YELLOW  to activate “Move station”.
Select the insertion position with  a/b  or  0 – 9 .
Press  OK to confirm.
Child lock
With the child lock you can bar access to all stations 
immediately or daily for a certain time period.
To use this function, you have first to define your PIN.
NOTE
•  The TV power will be turned off if no PIN is entered for 
several seconds.
•  As a precautionary measure, make a note of your PIN  on the back of this operation manual, cut it out and 
keep it in a safe place that children cannot reach.
•  See page 52 if you lose or forget your PIN.
1
2
3
1
2
3
1
2
3
4
5
 37
L C -5 2H D1E -g b.i n dd   3 7LC-52HD1E-gb.indd   372008/0 3/2 4   1 5:0 1:2 52008/03/24   15:01:25
 
						

							
Menu operation
Geometry menu
In this menu you can set the geometry values of your 
connected PC. First connect PC to EXT7 (ANALOG 
RGB) or to EXT5/6 using HDMI/DVI conversion cable.
Recording
TV menu
Picture horizontal
Picture vertical
Phase position 0
0
0
Geometry
Picture Sound Conn
Items
Picture horizontal
Picture vertical
Phase position*
*  May not be displayable depending on the signal.
Other menu items
Some of the useful features can be directly called up by 
pressing assigned buttons on the remote control.
Extended functions menu
The Extended functions menu provides alternative way 
to access frequently used functions/menus.
Recording
TV menu
DR archive
DVB radio
Favourites
PhotoViewer
Index
Teletext subtitles Εxtended functions
Picture Sound
Items
DR archive
DVB radio
Favourites
PhotoViewer
Index
Teletext subtitles
Timer functions
In this menu you can have the TV set switch off (to 
standby) daily at a certain time automatically. You can 
also have it emit an alarm (reminder) daily at a certain 
time. This is also possible when the TV is in standby 
mode (wake up).
PIP
In this menu, you can adjust all settings for the Picture-
in-Picture display, such as: type, position, window size. 
To call this menu you must activate the PIP mode. See 
page 23 for detailed operation.
Language
You can select a language from the Setup menu. 
Select from among 19 languages. (Czech, Danish, 
Dutch, English, Finnish, French, German, Greek, 
Hungarian, Italian, Norwegian, Polish, Portuguese, 
Russian, Slovak, Slovenian, Spanish, Swedish, Turkish)
Miscellaneous
There is an explanatory text for each function. If the Info 
text is not shown, press  INFO to activate.External sources
Use the External Sources screen to select/check the 
external equipment connected to the terminal(s) on the 
back of the TV.
To watch images from external 
AV equipment, press  b.
•  To close the External Sources 
screen, press  b again.
Press  a/b  to select the 
corresponding terminal, and 
then press  OK.
NOTE
•  If AQUOS LINK-compatible device connected to EXT 5 or 
6 sends model-specific data to the TV, its device name is 
displayed.
1
2External sources
VIDEO
DVD-REC
DVD
EXT3
EXT4
EXT5
EXT6
EXT7External sources
VIDEO
DVD-REC
DVD
EXT3
EXT4
EXT5
EXT6
EXT7
Still image
You can freeze a motion picture on the screen.
Press  3.
Press  3 again to exit still image.
NOTE
•  This function may not be available depending on signal 
condition.
1
2
 38
LC -5 2H D1E -g b.i n dd   3 8LC-52HD1E-gb.indd   382008/0 3/2 4   1 5:0 1:2 72008/03/24   15:01:27