Sharp Lc 46hd1e Operation Manual

Initial installation
Initial installation overview
Follow the below steps one by one when using the TV for the first time. \
Some steps may not be necessary 
depending on your TV installation and connection.
 9
n Connect the AC cord (Page 5)
o Connect antenna (Page 5)
Analogue/DVB-C/DVB-T antenna:
Plug the antenna of antenna system, cable system, or room antenna to ANT 2.
Cable is already connected between ANT 1 and ANT OUT at the factory.
Satellite antenna:
Connect an antenna plug, e.g., from the...

Initial installation
Initial installation wizard
When the TV powers on for the first time after 
purchase, the initial auto installation wizard appears. 
Follow the menus and make the necessary settings 
one after another.
Proceed
Initial installation -> Language
NOTE
•  You can repeat this installation process by conducting the “Repeat initial installation” command. Press  INFO, the 
option is located in the third line from the top.
Buttons to be used:
a /b /c /d :
  Move the cursor and select the...

Initial installation
Positioning/aligning DVB-T antenna
If you are receiving one or more DVB-T stations with 
picture and sound interference then you should change 
the installation location and alignment of the antenna. 
Ask your dealer to tell you which channels are used to 
broadcast the DVB-T stations in your region.
 Prerequisite : In normal TV mode, with no other 
menu screen active, and a DVB-T station is 
received and selected.
Press  MENU  and the TV menu screen displays.
Press  c/d  to select...

Switching on/off
Turning on/off the power
Press a on the TV.
Switch it off by pressing  a on the TV.
•  However, please bear in mind that EPG data (electronic 
programme guide) will be lost, and programmed timer 
recordings will not be performed by the TV.
Standby mode
If the TV set is switched on, you can switch it to 
standby by pressing  B on the remote control.
Switching on from standby
From standby, press  B on the remote control or 
pressing any of the numeric buttons  0 - 9.
Or, switch on the TV...

With the favourites lists:
You can save and select your favourite stations 
in 6 favourites lists (e.g. for multiple users). Each 
favourites list can contain up to 99 stations. After initial 
installation, 10 stations from the station list are already 
stored in the first list. Change the favourites list to suit 
your requirements (see “Select/change favourites” on 
page 37).Press  OK with no other menu screen active.
Favourites -> FavouriteList1
Press  RED to display the favourite list.
Press  0 - 9...

Connecting external devices
The TV’s integrated Connection wizard helps you connect new external devices and make cable changes. Before 
actually connecting the external device, run the Connection wizard and register the equipment to be connected.
E Before connecting ...
Carefully read the operation manual of each external device for possible connection types. This also helps you get 
the best possible audiovisual quality to maximise the potential of the T\
V set and the connected device. Make a 
note...

Connection wizard
The integrated Connection wizard shows you which 
terminal you should connect your equipment to. 
Connect the equipment according to the diagram and 
follow the messages one after the other.
NOTE
•  New devices should not be connected until they have been  registered in the connection wizard.
Press  MENU  and the TV menu screen displays.
Press  c/d  to select “Connections”, and then 
press  b to move down.
Press  a/b  to select “AV setup”, and then press 
OK .
•  The connection wizard...

Connecting external devices
HDMI connection
The HDMI connections (High Definition Multimedia 
Interface) permit digital video and audio transmission 
via a connection cable from a player.
The digital picture and sound data are transmitted 
without data compression and therefore lose none of 
their quality. Analogue/digital conversion is no longer 
necessary in the connected devices, which also would 
result in quality losses.
HDMI/DVI conversion
Using a DVI/HDMI adapter cable, the digital video 
signals...

Connecting external devices
Audio connection
Analogue audio:
  Connect the analogue audio signal from the PC or the SetTopBox via stereo cable to the AUDIO 
IN (L/R) jack on the TV set.
•  The sound is played via the speakers connected to 
the TV set or a speaker system.
Digital audio:•  An external digital audio signal can be reproduced via the integrated Dolby Digital Decoder or via an 
externally connected digital audio amplifier.
Connect the digital audio signal from the PC or 
the SetTop-Box via a...

Connecting external devices
PC compatibility chart
ResolutionHorizontal 
Frequency Vertical 
Frequency Analogue (D-
Sub) Digital (HDMI) VESA Standard
VGA 640 g 480 31.5 kHz 60 Hz
✔✔
g
SVGA 800 g 600 37.9 kHz 60 Hz
✔✔
g
XGA
1024  g 76848.4 kHz 60 Hz
✔✔
g
SXGA 1280 g 1024 64.0 kHz 60 Hz
✔✔
g
FULL HD 1920 g 1080 67.5 kHz 60 Hz
✔
NOTE
•  This TV has only limited PC compatibility, correct operation 
can only be guaranteed if the video card conforms exactly 
to the VESA 60Hz standard. Any variations from this...