Sharp Lc 42x20e Operation Manual

							
Quick guide
Initial auto installation
When the TV powers on for the first time after 
purchase, the initial auto installation wizard appears. 
Follow the menus and make the necessary settings 
one after another.
Checking signal strength and 
channel strength
If you install a DVB-T antenna for the first time or 
relocate it, you should adjust the alignment of the 
antenna to receive a good reception while checking the 
antenna setup screen.Press  MENU  and the menu screen displays.
Press  c/d  to select “Setup”. 
Press  a/b  to select “Aerial Setup-DIGITAL”, 
and then press  OK.
E Checking signal strength
 Press  a/b  to select “Signal Strength”.
Signal Strength  Supply Voltage 
Channel Strength 
Signal Strength 
Quality Current Max 
0 
CH No.
21 
0 
Current Max  0 0
E Checking channel strength
 Press a/b  to select “Channel strength”, and 
then press  OK.
•  You can input a specified frequency band using  0 -  9 
numeric buttons.
Signal Strength  Supply Voltage 
Channel Strength 
Signal Strength 
Quality Current Max 
0 
CH No.
21 
0 
Current Max  0 0 2 6 5 . 2 MHz
Position and align the antenna so that the 
maximum possible values for “Signal Strength” 
and “Quality” are obtained.
NOTE
•  The values of “Signal Strength” and “Quality” indicate when 
to check the appropriate alignment of the antenna.
1
2
3
4
Press  a on the TV.•  The initial auto installation wizard appears.
Setting the on-screen display language
English
Italiano
Svenska
Setting the country (Location of TV set screen)
Austria A  B/G
Finland 
FIN B/G
Greece GR B/G
•  The Location of TV set screen only appears during  the first installation.
Starting channel search
Analogue Search
Digital Search
 
•  If you want to search for more broadcasts, execute 
“Auto Installation” again from the Setup menu.
1
2
3
4
Confirm the following  before turning on 
the power
E  Is the antenna cable connected?
E  Is the AC cord plugged in?
Press  a/b /c /d  to select the desired language, 
and then press  OK. 
Press  a/b /c /d  to select your country or area, 
and then press  OK.
Press  c/d  to select “Digital Search” or “Analogue 
Search”, and then press  OK. 
The TV searches for, sorts and stores all the 
receivable TV stations according to their 
settings and the connected antenna.
•  To abort the initial auto installation in progress, press 
END .
NOTE
•  If you turn off the power on the TV after performing step 4,  the initial auto installation wizard does not appear. The auto 
installation function allows you to execute the installation  
again from the Setup menu. (Page 26)
•  The initial auto installation wizard will go off if you leave  the TV unattended for 30 minutes before searching for 
channels in step 5.
5
 9
LC -4 2X 20E -g b.in dd   9LC-42X20E-gb.indd   92 007/0 9/0 4   1 6:3 1:1 92007/09/04   16:31:19
 
						

							
Watching TV
TV indicator status
B indicator Status
Off Power off
Green Power on
Red Standby
NOTE
•  If you are not going to use this TV for a long period of time,  be sure to remove the AC cord from the power outlet.
•  A small amount of electric power is still consumed even  when  a is turned off.
Changing channels
With P r/Ps :   With 0 - 9:
Switching between analogue and 
digital broadcasts
Selecting external video source
Once the connection is made, press 
b  to display the INPUT SOURCE 
screen, and then press  a/b  to switch 
over to the appropriate external source 
with  OK.INPUT SOURCE 
TV  EXT1
EXT2
EXT3
EXT4
EXT5
INPUT SOURCE 
TV  EXT1
EXT2
EXT3
EXT4
EXT5
Selecting Sound mode
DTV mode:
E If multi sound modes are received, each 
time you press  2 the mode switches as 
follows.
Audio (ENG) : STEREO
L/R LRLR
Audio (ENG) : CH A
CH A CH B CH AB
Audio (ENG) : MONO
E Press c/d  to select L or R sound when 
the STEREO or DUAL MONO screen is 
displayed.
Audio (ENG) : STEREO
L/R LRLR
NOTE
•  The sound mode OSD disappears in 6 seconds.
•  Selectable items vary depending on the received 
broadcasts.
ATV mode:
Each time you press  2, the mode switches as 
illustrated in the following tables. 
NICAM TV broadcasts selection
Signal Selectable items
Stereo NICAM STEREO, MONO
Bilingual
NICAM CH A, NICAM CH B, NICAM CH AB, 
MONO
Monaural NICAM MONO, MONO
A2 TV broadcasts selection
Signal Selectable items
Stereo STEREO, MONO
Bilingual CH A, CH B, CH AB
Monaural MONO
NOTE
•  When no signal is input, the sound mode will display 
“MONO”.
•  However, please bear in mind 
that EPG data (electronic 
programme guide) will be 
lost, and programmed 
timer recordings will not be 
performed by the TV.
Daily operation
Switching on/off
Turning on/off the power
Press  a on the TV.
Switch it off by pressing  a on the TV. 
E Watching analogue 
broadcastsE Watching digital 
broadcasts  
Standby mode
E To standby mode
If the TV set is switched on, you can switch it to 
standby by pressing 
B on the remote control.
E Switching on from standby
From standby, press  B on the remote control.
 10
LC -4 2X 20E -g b.in dd   1 0LC-42X20E-gb.indd   102007/0 9/0 4   1 6:3 1:2 02007/09/04   16:31:20
 
						

							
Watching TV
EPG (Electronic Programme Guide)
EPG (Electronic Programme Guide) is a programme list that is displayed on the screen. With the EPG, you can 
check the schedule of DTV/RADIO/DATA, view detailed information about them, tune to an event currently on-air 
and set a timer for future events.
EPG Overview
E Basic functionsE Useful functions
E Select a programme using EPG (Page 12)
E  Check programme information (Page 12) E
 Search for a programme by category (Page 12)
E  Search for a programme by date and time    
 (Page 12)
E  Timer recoding using EPG (Page 13)
Useful settings for using EPG
Press  MENU  to display the menu screen.
Press  c/d  to select “Digital Setup”.
MENU    [
Digital Setup  ... 
EPG Setup]
Digital Setup  Information 
REC Picture Size
Download Setup
EPG Setup
Subtitle
CI Menu [Yes]
[16:9 TV]
Press 
a/b  to select “EPG Setup”, and then 
press  OK.
Ye s No
EPG Setup
Display Range Setup
Genre Icon Setup
Press 
c/d  to select “Yes” or “No”, and then 
press  OK.
1
2
3
4E EPG Setup (setting for receiving EPG data)
If you want to use the EPG for digital stations, select 
“Yes”. The EPG data must be automatically captured 
while the TV set is in standby mode. After setting to 
“Yes”, it may take some time to turn off the power 
using the remote control due to the process of the data 
capture.
NOTE
•  If the TV main power is switched off, the EPG data will not 
capture.
E Display Range Setup
The Display range setup allows you to select three 
types of time spans for display on the screen.
E Genre Icon Setup
You can grey out or place a mark on desired genres 
and smoothly search for programmes you frequently 
watch.
Genre Icon List
Icon Genre Icon Genre
Movie/Drama Music/Ballet/Dance
News/Current affairs Arts/Culture (without 
music)
Show/Game show Social/Political Issues/
Economics
Sports Education/Science/
Factual Topics
Children’s/Youth 
programmes Leisure hobbies
Item
Wide Angle:  Display six hours of programme information.
Zoom:  Display three hours of programme information.
Vertical Angle:  Change to the EPG display format with a 
vertical time span.
Common OperationEPG display settings
 11
L C -4 2X 20E -g b.in dd   1 1LC-42X20E-gb.indd   112007/0 9/0 4   1 6:3 1:2 02007/09/04   16:31:20
 
						

							
Selecting a programme using EPG
3 Check programme information
Press a/b /c /d  to select the programme you 
want to check.
Press  R.
EPG    [Mon]16/04  10:57 AM
[DTV-TV] Today (Tue)20 (Wed)21  (Thu)22  (Fri)23 (Sat)24 (Sun)25 (Mon)26
040
10 : 00AM - 1 : 00 AM BBC News 24
BBC News
Programme Info.
Back to EPG The BBC’s rolling news service with headlines every 15 minutes.
10 AM11 0 PM 1 2 3
BBC TWO    002
BBC THREE   007
BBC FOUR    010
BBC FIVE    012
CBBC Channel  030
BBC 1     061
BB22     062
BBC NEWS 24  340
BBCi     351
BBC ONE    999 SIT 1      994
SIT 4      997 This is BBC THREE 
BBC NEWS BBC NEWS 
BBC NEWS BBC NEWS 
This is BBC THREE 
BBCi BBCi 
This is BBC THREE 
RNextB
OK: Select : Enter6: BackEPG: Exit
 Press 
OK to tune to the selected programme.
4 Search a programme in a category
Press  G.
Press  a/b  to select the desired genre, and 
then press  OK.
Press  a/b  to select a programme you want to 
watch, and then press  OK.
EPG    [Mon]16/04  10:57 AM
[DTV-TV] Today  (Tue)20  (Wed)21   (Thu)22   (Fri)23  (Sat)24  (Sun)25  (Mon)26
Back to EPG
CBBC Cahnnel  030  time   Mon 19/05  10 : 50 AM - 11 : 05 AMBBC TWO  002  School is Lock   Mon 19/05  10 : 50 AM - 11 : 10 AMCBBC Cahnnel  030  Words and Pictures   Mon 19/05  11 : 05 AM - 11 : 20 AM
ROK: Select : Enter6: BackEPG: Exit
Movie/Drama
News/Current affairs
Show/Game show
Sports
Children’s/Youth programmes
Music/Ballet/Dance
Arts/Culture (without music)
Social/Political Issues/EconomicsEducation/Science/Factual TopicsLeisure hobbies
Today [AM] Today [PM]  [Tue] 20 AM [Tue] 20 PM
•  Refer to page 11 for the genre setting. 
1
2
3
1
2
3
5 Search for a programme by date/time
Press  Y.
Press  c/d  to select the desired time span and 
then press  OK.
EPG    [Mon]16/04  10:57 AM
[DTV-TV] Today (Tue)20 (Wed)21  (Thu)22  (Fri)23 (Sat)24 (Sun)25 (Mon)26
Search by Time
Back to EPG
10 AM11 0 PM 1 2 3
BBC TWO    002
BBC THREE   007
BBC FOUR    010
BBC FIVE    012
CBBC Channel  030
BBC 1   061
BB22     062
BBC NEWS 24  340 This is BBC THREE 
BBC NEWS BBC NEWS 
BBC NEWS BBC NEWS 
This is BBC THREE 
RNextNextB
OK: Select
: Select Time
: Enter6: BackEPG: Exit
Enter +1 WeekGYOK: Enter0 AM - 
6 AM
6 AM - 
0 PM 0 PM - 
6 PM 6 PM - 
0 AM
To d a y
BBC ONE    999 SIT 1   994
SIT 4   997This is BBC THREE 
Press 
a/b  to select the desired programme, 
and then press  OK.
1
2
3
Basic Operation
E Display the EPG screen
Selecting a programme
NOTE
•  When you select a programme outside of the current time 
span, the timer setting screen displays. (Page 13)
Press  EPG.EPG    [Mon]16/04  10:57 AM
[DTV-TV] Today (Tue)20 (Wed)21  (Thu)22  (Fri)23 (Sat)24 (Sun)25 (Mon)26
040
10 : 00AM - 1 : 00 AM BBC News 24
BBC News
10 AM11 0 PM 1 2 3
BBC TWO    002
BBC THREE   007
BBC FOUR    010
BBC FIVE    012
CBBC Channel  030
BBC 1   061
BB22     062
BBC NEWS 24  340
BBCi     351
SIT 3   996
BBC ONE    999 SIT 1   994
SIT 2   995
SIT 5   998 SIT 4   997 This is BBC THREE 
BBC NEWS BBC NEWS 
BBC NEWS BBC NEWS 
This is BBC THREE 
BBCi BBCi 
This is BBC THREE 
OK: Select : Enter6: BackEPG: Exit Programme info.Search By GenreSearch By DateTimer ListRG YB
E Select a programme
1  Press  c/d  to select the time 
span you want to search.
• Continue to press  d to display 
programmes in the next time span.
2  Press  a/b  to select the desired programme.
• If  a or  b are displayed on the left of the services, continue to press 
a /b  to display next or previous screen.
E Close the EPG screen
Press  EPG again.
2 1
345
Programme Information
Watching TV
 12
L C -4 2X 20E -g b.in dd   1 2LC-42X20E-gb.indd   122007/0 9/0 4   1 6:3 1:2 12007/09/04   16:31:21
 
						

							
Watching TV
Timer recording using EPG
You can record TV programmes using data from the 
EPG.Press  EPG.
Press  a/b /c /d  to select the programme you 
want to record, and then press  OK.
Press  c/d  to select the preferred timer setting, 
and then press  OK.
EPG    [Mon]16/04  10:57 AM
[DTV-TV] Today (Tue)20 (Wed)21  (Thu)22  (Fri)23 (Sat)24 (Sun)25 (Mon)26
040
10 : 00AM - 1 : 00 AM BBC News 24
BBC News
Programme Info.
Back to EPG [Age 5 - 7] Paul Ewing reads the story of a bear
and a lunch and looks at the end sound the words
bug and dog.
RNextB
OK: Select : Enter6: BackEPG: Exit
Watch
Record No
•  If you select “No”, the TV returns to the EPG screen.
E Selecting “Watch” in the timer setup 
screen
This setting allows you to switch to a programme at a 
set time.
1  Press  c/d  to select “Watch”, and then press  OK.
2  Press  c/d  to select “Yes”, and then press  OK.
•  The selected TV programme is marked with an icon.
E Selecting “Record” in the timer setup 
screen
This setting allows you to record a programme at a set 
time.
1  Press  c/d  to select “Record”, and then press  
  OK.
2  Press  c/d  to select the preferred timer recording  
  type, and then press  OK.
1
2
3
Item
AQUOS LINK:  Record a programme at a set time when a 
device compatible with AQUOS LINK is connected.
AV LINK:  Record a programme at a set time when a 
device compatible with AV LINK is connected.
VHS tape:  Record a programme at a set time when a 
device compatible with VHS tape is connected.
Cancelling the timer recording
Press  EPG.
Press  a/b /c /d  to select the programme on 
timer setup, and then press  OK.
Press  c/d  to select “Cancel” , and then press 
OK .
E Cancelling using B button on the remote 
control
Press  EPG.
Press  B to display the timer recording screen.
Press  a/b  to select a programme with a set 
timer recording you want to change, and then 
press  OK.
Press  c/d  to select “Cancel” and then press 
OK .
1
2
3
1
2
3
4
NOTE
•  Refer to pages 15-17 and 21 for connecting external 
devices.
• 
The selected TV programme is marked with an icon.
 13
L C -4 2X 20E -g b.in dd   1 3LC-42X20E-gb.indd   132007/0 9/0 4   1 6:3 1:2 12007/09/04   16:31:21
 
						

							
Buttons for teletext operations
Buttons Description
P ( r /s ) Increase or decrease the page number.
Colour 
(R/G/Y/B) Select a group or block of pages displayed 
in the coloured brackets at the bottom of the 
screen by pressing the corresponding 
Colour 
(R/G/Y/B)  on the remote control unit.
0 - 9 Directly select any page from 100 to 899 by 
using 0 - 9.
v  (Top/
Bottom/Full) Switch the Teletext image to Top, Bottom or 
Full.
k  (Reveal 
hidden Teletext) Reveal or hide hidden information such as an 
answer to a quiz.
3  (Freeze/
Hold) Stop updating Teletext pages automatically or 
release the hold mode.
[  (Subtitle for 
Teletext) Display the subtitle or exit the subtitle screen.
•  Subtitles will not be displayed when 
the service does not contain subtitle 
information.
1  (Subpage) Reveal or hide subpages.
• 
R button: Move to the previous subpage.
•  G button: Move to the following subpage.
•  These two buttons are shown on the  screen by the signs  l and  k.
Using the MHEG5 application (UK 
only)
Some services bring you programmes with the MHEG 
(Multimedia and Hypermedia Expert Group) application 
encoded, letting you experience DTV interactively.
When provided, the MHEG5 application will start when 
you press  m.
Sample MHEG5 screen
Watching TV
Teletext
What is Teletext?
Teletext broadcasts pages of information and 
entertainment to specially equipped television sets. 
Your TV receives Teletext signals broadcast by a TV 
network, and decodes them into graphical format for 
viewing. News, weather and sports information, stock 
exchange prices and programme previews are among 
the many services available.
Turning on and off Teletext Select a TV channel or external source 
providing a Teletext programme.
Press  m to display the Teletext.
  100  100   ARD-Text           10.09.04       14:14:42ARD TEXT
Teletext im Ersten
Bulmahn: Bildung statt Eigenheim . . . . . . . .    120
Wird auch der Nahverkehr teurer? . . . . . . . .    121
Australien: Keine Zugeständnisse  . . . . . . . .    122
Tote bei Zugunglück in Schweden . . . . . . . .    532
Tennis: Haas unterliegt Hewitt . . . . . . . . . . . .  204
Formel 1: Schumacher erneut vorne . . . . . . .  213
Tagesschau . .  110/112  Kultur. . . . . . . . .    500
Wetter. . . . . . . . . . .  170  Gesellschaft . . .  530
Sport. . . . . . .   200/600  Lotto/Toto . .    666
TV Guide . . .  300/400  Wirtschaft. . . . . .   700
                  Internet: www.ard-text.de
–         +Inhalt       tagesschau
Index
> 101
•  Many stations use the TOP operating system, while 
some use FLOF (e.g. CNN). Your TV supports both 
these systems. The pages are divided into topic 
groups and topics. After switching on the teletext, up 
to 2000 pages are stored for fast access.
• Each time you press  m, the screen switches as 
shown below.
• Press  m again to display the Teletext on the right 
screen and the normal image on the left screen.
•  If you select a programme with no Teletext signal,  “No Teletext available.” displays.
•  The same message displays during other modes if no  Teletext signal is available.
1
2
NOTE
• Teletext will not work if the selected signal type is RGB. (See page 32) TELETEXT
TELETEXT
 14
L
C -4 2X 20E -g b.in dd   1 4LC-42X20E-gb.indd   142007/0 9/0 4   1 6:3 1:2 12007/09/04   16:31:21
 
						

							
Connecting external devices
E Before connecting ...
•  Be sure to turn off the TV and any devices before making any connections.
•  Firmly connect a cable to a terminal or terminals.
•  Carefully read the operation manual of each external device for possible connection types. This also helps you get the best possible audiovisual quality to maximise the potential of t\
he TV and the connected device.
Introduction to connections
The TV is equipped with the terminals as showed below. Find the cable corresponding the TV’s terminal and 
connect the device.
NOTE
•  The cables illustrated in pages 15 to 18 are commercially available items.
HDMI device (Page 16)
Game console or 
camcorder (Page 16)
Video recording device  (Pages 16 and 17)
HDMI Cable
DVI/HDMI Cable
ø 3.5 mm stereo minijack cable S-video cable
*
AV cable*
Audio cable
Component cable
SCART cable
or
Audio cable
or
Optical audio cable
Audio device  (Page 18)
or
*  When using an S-video cable, you also need to connect an audio cable (R\
/L).
 15
L C -4 2X 20E -g b.in dd   1 5LC-42X20E-gb.indd   152007/0 9/0 4   1 6:3 1:2 12007/09/04   16:31:21
 
						

							
HDMI connection
Connecting external devices
The HDMI connections (High Definition Multimedia 
Interface) permit digital video and audio transmission 
via a connection cable from a player/recorder. The 
digital picture and sound data are transmitted without 
data compression and therefore lose none of their 
quality. Analogue/digital conversion is no longer 
necessary in the connected devices, which also would 
result in quality losses.
DVI/HDMI conversion
Using an DVI/HDMI adapter cable, the digital video 
signals of a DVD can also be played via the compatible 
HDMI connection. The sound must be fed in 
additionally.
Both HDMI and DVI use the same HDCP copy 
protection method.
NOTE
• If a connected HDMI device is AQUOS LINK compatible, you 
can take advantage of versatile functions. (Pages 20 - 22)
•  Video noise may occur depending on the type of HDMI cable used. Make sure to use certified HDMI cable.
•  When playing the HDMI image, the best possible format for  the picture will be detected and set automatically.
Supported video signal:
576i, 576p, 480i, 480p, 1080i, 720p, 1080p
See page 36 for PC signal compatibility. You will enjoy accurate colour reproduction and 
high quality images through the EXT 8 terminal 
when connecting a DVD recorder or other recording 
equipment.
YPB
(CB)L
RPR
(CR)COMPONENT
AUDIO
Example of connectable devices
E  VCR  E DVD  E Blu-ray player/recorder
Example of connectable devices
E DVD  E Blu-ray player/recorder
Component connectionYPB
(CB)PR
(CR)
You can use the EXT 3 terminal when connecting to a 
game console, camcorder, a DVD recorder and some 
other equipment.
NOTE
•  When using an S-video cable, you also need to 
connect an audio cable (R/L).
•  EXT3: The S-VIDEO terminal has priority over the VIDEO  terminal.
Example of connectable devices
E  VCR  E DVD  E Blu-ray player/recorder 
E  Game console  E Camcorder
S-VIDEO/VIDEO connection
or
DVI/HDMI adapter cable
ø 3.5 mm stereo minijack 
cable HDMI cable
Audio cableComponent 
cable
or
AV cable S-video cable
E After connecting
HDMI Audio Select
After connecting, you must set the audio signal 
compatible with the cable you use for the HDMI 
device. Go to MENU > Option > HDMI Audio Select
Select “Digital” for audio signals via the 
HDMI terminal. Select “Analogue” for audio 
signals via the AUDIO jack (EXT6).
1
2
 16
LC -4 2X 20E -g b.in dd   1 6LC-42X20E-gb.indd   162007/0 9/0 4   1 6:3 1:2 12007/09/04   16:31:21
 
						

							
SCART connection
Connecting external devices
E When using the EXT 1 (SCART) terminalE When using the EXT 2 (SCART) terminal
If your VCR supports TV-VCR advanced AV Link 
systems, you can connect the VCR using a fully wired 
SCART cable.
Controlling devices with SCART using AV Link 
This TV incorporates four typical AV Link functions for smooth connections between the TV and other audiovi\
sual 
equipment.
One Touch Play
While the TV is in standby mode, it automatically turns on and plays back the image from the audiovisual source 
(e.g. VCR, DVD).
TV Standby
When the TV enters standby mode, the connected audiovisual equipment (e\
.g. VCR, DVD) enters standby mode 
as well.
WYSIWYR (What You See Is What You Record)
When the remote control unit of the connected VCR has the WYSIWYR button, you can automatical\
ly start 
recording by pressing the WYSIWYR button.
Preset Download
Automatically transfers the channel preset information from the tuner on the TV to the one on the connected 
audiovisual equipment (e.g. VCR) via the EXT 2 terminal.
NOTE
•  Refer to the operation manuals of external equipment the details.
•  Only works when the audiovisual equipment is connected to the EXT 2 term\
inal on the TV with AV Link via a fully wired SCART.
•  The use of the AV Link function is only possible if the TV-set has enforced a complete auto installation with the connected  audiovisual equipment. (Page 9, initial auto installation)
  The availability of the AV Link function depends on the audiovisual equipment used. Depending on \
the manufacturer and type 
of equipment used, it is possible that the described functions may be co\
mpletely or partially unusable. 
Example of connectable devices
E  Decoder
Example of connectable devices
E VCR  E DVD recorder
NOTE
•  In cases when the decoder needs to receive a signal from the TV, make sure to select the appropriate input terminal to which 
the decoder is connected in “Manual adjust” in the “Analogue Se\
tting” menu. (Page 27)
•  TV-VCR advanced AV Link systems may not be compatible with some external sources.
•  Do not connect the decoder to the EXT2 terminal.
•  You cannot connect the VCR with Decoder using a fully wired SCART cable when selecting “Y/C” under the EXT2 in the  “Input Select” menu.
SCART cable
Decoder
SCART cable
SCART cable
Decoder
VCR
 17
L C -4 2X 20E -g b.in dd   1 7LC-42X20E-gb.indd   172007/0 9/0 4   1 6:3 1:2 22007/09/04   16:31:22
 
						

							
Connecting external devices
DIGITAL AUDIO INL
R
AUX1 INL
R
AUX OUT
Speaker/amplifier connection
Connect an amplifier with external speakers as shown below.
E Connecting an amplifier with analogue audio inputE Connecting an amplifier with digital audio input
E After  connecting
Digital audio output setting
After connecting an amplifier with digital audio input 
and external speakers as shown, you should set an 
audio output format compatible with the programme 
you are watching or the device connected.
  Go to MENU > Option > Digital Audio Output  > select “PCM” or “Dolby Digital”
Optical AUDIO 
cable
Audio cable
 18
Amplifier with 
analogue audio input
Amplifier with 
digital audio input
L C -4 2X 20E -g b.in dd   1 8LC-42X20E-gb.indd   182007/0 9/0 4   1 6:3 1:2 22007/09/04   16:31:22