Sharp Lc 42sb55 Operation Manual

LC-26SB25E 
LC-26SB25S
LC-32SB25E
LC-32SB25S
LC-42SB55E
LC-42SB55S
LCD COLOUR TELEVISION
LCD-FARBFERNSEHGERÄT
TÉLÉVISEUR COULEUR À ÉCRAN
CRISTAUX LIQUIDES (LCD) 
TELEVISORE A COLORI LCD
LCD-KLEURENTELEVISIE
TELEVISIÓN EN COLOR LCD
TELEVISOR LCD A CORES
SHARP ELECTRONICS (Europe) GmbH
Sonnistraße 3, D-20097 Hamburg, Deutschland
SHARP CORPORATION
Printed in China
Gedruckt in China
Imprimé en Chine
Stampato in Cina
Afgedrukt in China
Impreso en China 
Impresso na China
LC-26SB25E/LC-32SB25E/LC-42SB55E...

SPECIAL NOTE FOR USERS IN THE U.K.
The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 5A fuse. 
Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked 
 or ASA and of 
the same rating as above, which is also indicated on the pin face of the\
 plug, must be used.
Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse cover fitted.
In the unlikely event of the socket outlet in your home not being compat\...

operation manual
Contents ��������������������������������������������������������������������  1
introduction  ���������������������������������������������������������������  2
Dear SHARP customer  ����������������������������������������  2
Important Safety Precautions  ������������������������������� 2
Remote control unit ����������������������������������������������  3
preparation  ���������������������������������������������������������������  5
Supplied accessories...

Cleaning—Unplug the AC cord from the AC outlet before cleaning the product� Use a damp cloth to clean the product� Do not 
•	
use liquid cleaners or aerosol cleaners�
Water and moisture—Do not use the product near water, such as bathtub, washbasin, kitchen sink, laundry 
•	
tub, swimming pool and in a wet basement�
Do not place vases or any other water-filled containers on this product� 
•	
The water may spill onto the product causing fire or electric shock�
Stand—Do not place the product on an unstable...

introduction
0
poWer
Press to turn the LCD TV on or enter 
standby mode�
ViDeo
Press this button you could select YPbPr, 
Side AV, HDMI 1, HDMI 2, HDMI 3�
SCart
Press this button you could select  
SCART 1, SCART 2�
pC
Press to direct to the PC mode�
tV
Press to direct to the TV mode�
0-9 DiGit ButtonS
To select a TV channel directly�
epG
Press this button to display electronic 
program guide in TV mode�
pre pr
To display the previous selected TV channel�
b (input SourCe)
Select an input source�
aSpeCt...

introduction
1
VGA
Y
LR
LR Pb
Pr
SCART 1S CART 2
AUDI
O
SPDIF OUT
AUDIO OU T
PC IN
COMPONEN T
75
S-VIDEO
VIDEO L R C.I.
AV IN
3
4
2
5
6
8
7
910
11
13
12
14
15
16
P
MENU
SER VICE
1  Power connector
2  SERVICE socket
3  HDMI 1
4  HDMI 2
5  PC IN (VGA/AUDIO)
6  Component Video and L/R Audio 
input 7  SPDIF Output (Digital audio out)
8  AV L/R Audio Output
9  SCART 1 (CVBS Tuner out)
10  SCART 2 (CVBS Monitor out)
11  Tuner Input
12  COMMON INTERFACE slot
13  Earphone Output 14  Composite ( AV IN, AV/LR)
15...

preparation
Operation ManualQuick Setup Guide42” 26”
32”
0
Put the TV face down on a safe surface that is 1� covered by a soft and smooth cloth.
Adjust the TV stand to the base column.
2� 
Fasten 4 screws.3� 
Put the TV face down on a safe surface that is 1� covered by a soft and smooth cloth.
Unscrew the 4 bolts that fasten the base 
2� column to the TV by using a cross-head 
screwdriver. (not supplied)
Detach the stand from the bottom of the TV. 
3� 
3
3
3
3
W
Ht V screen size  
( i nches) V
e Sa...

preparation
Insert two AAA batteries into Remote control. 1� Make sure (k) and (l) are facing the proper 
direction.
Replace the cover.2� 
noteIf the remote control will not to be used for a long 
•	
time, remove the batteries to avoid remote control damage�
CautionImproper use of batteries can result in chemical leakage or explosion� Be sure to follow the instructions below �
Do not mix batteries of different types� Different types of batteries have different characteristics�
•	
Do not mix old and new...

Quick guide
Follow the below steps one by one when using the TV for the first time� Some steps may not be necessary depending 
on your TV installation and connection�
preparation
1
power on and run the auto installation
2
Watch tV
3
Π Connect antenna cable to 
the antenna terminal.  
75Ω
 If necessary, insert CA card 
into the CI slot to watch 
scrambled broadcasts.  
Ž Connect the AC cord to the 
TV. 
Π Turn on the TV power with a.  
 Run the initial auto 
installation. 
 
4...

Quick guide
After unpacking and plugging in your new LCD TV, please proceed with the following steps to set-up your TV� If you 
do not run this set-up function, your LCD TV may not operate properly �
Confirm the following  before turning on the power
E Is the antenna cable connected?
E Is the AC cord plugged in?
Press the 1� < or > buttons to select your 
language. And press the Green button to 
continue.
TV Installation
Please select your language .
Next

esky
Dansk
Deutsch

English
Español
Français...