Sharp Lc 42rd2e Operation Manual

							19
Menu operations
HDMI Setup
HDMI (High-Definition Multimedia Interface) terminal
selection.
1To watch an HDMI equipment image, select
“EXT5” or “EXT6” (the terminal which you are
using) from “INPUT SOURCE” menu using b
on the remote control unit or TV.
2Press MENU and the MENU screen displays.
3Press c/d to select “Option”.
4Press a/b to select  “HDMI Setup”, and then
press OK.
• “HDMI Setup” is displayed only when “EXT5” or
“EXT6” is selected from the INPUT SOURCE menu.
DNR (Digital Noise Reduction)
Menu Operation: A (page 12)
Produce a clearer image. (Off, High, Low)
Colour System
Menu Operation: A (page 12)
You can change the colour system to one that is
compatible with the image on the screen. (AUTO, PAL,
SECAM, NTSC3.58, NTSC4.43, PAL-60)
NOTE
• Factory preset value is “AUTO”.
• If “AUTO” is selected, colour system for each channel is
automatically set. If an image does not display clearly,
select another colour system (e.g. PAL, SECAM).
• “NTSC3.58”, “NTSC4.43” and “PAL-60” cannot be
selected in TV tuner mode.
Input Select
Menu Operation: A (page 12)
For setting the signal type of external equipment.
NOTE
•If no (colour) image displays, try to change the other
signal type.
• Check the operation manual of the external equipment
for the signal type.
• TV, EXT5 and EXT6 are not displayed in Input Select.
• If both CVBS and RGB signals are input to EXT 1 or EXT 2
using a SCART cable, the TV may output an RGB signal
even though you have designated CVBS for the respective
terminal. This happens due to the setting of your external
equipment.
• EXT 3 has “Rear” and “Side” terminals. Confirm which
terminal you have connected, and select the appropriate
terminal under “Input Select”. When using S-VIDEO, select
“Rear” for EXT3.
AV only
TV/AV only
TV/DTV/AV only
MENU    [
Option ... 
HDMI Setup]
Option
Audio Only
DNR
HDMI Setup
[Off]
5Press a/b to select the desired item, and then
press OK.
6Press a/b/c/d to select the desired setting, and
then press OK.
Selectable items
RGB/YCbCr 4:4:4/
YCbCr 4:2:2
ITU601/ITU709
Normal/
Enhanced
Disable/Enable
Digital/Analogue HDMI Setup
items
Signal
Type*
Colour
Matrix*
Dynamic
Range*
Auto View
Audio
Select**Description
Select the video signal
type from the HDMI
terminal.
Select the internal colour
space conversion method
when an RGB signal is
input.
Select the signal amplitude
range. Usually, select
“Normal”.
Set whether or not to use
WIDE MODE based on
signal recognition,
including an HDMI signal.
Select “Digital” for audio
signal via the HDMI
terminal. Select “Analogue”
for audio signal via the
AUDIO jack.
NOTE
• Refer to your external equipment operation manual for
the signal type.
• Items marked * may be greyed out (with 4) depending
on the type of signal input from the external equipment.
• Item marked ** is only available when EXT5 is selected.
Input source Signal type
EXT 1Y/C, CVBS, RGB
EXT 2Y/C, CVBS, RGB
EXT 4PC (RGB), COMPONENT (Y, PB, PR) EXT 3CVBS, S-VIDEO
CVBS
Rear
Side
LC-32RD2E_GB_b07.2.1, 5:15 AM 19
 
						

							6
Remote control unit
Quick guide
117
18
19
20
21
22
23
24
25
26
27
29 28
30
31
32
33 4
5
15
166
7
8
9
10
11
12
13
143 2
1
(Teletext)
Select the TELETEXT mode. \(All TV
image, DTV/DA
image, TV/TEXT image\) \(See pages 21
and 31.\)
DTV
TELETEXT
2 (Standby/On)
Enter standby mode or tur
power
3 (Freeze/Hold)
\(See page 21.\)
4 (Subpage)
\(See page 21.\)
5 (Flashback)
Pr
in nor
while operating in EPG/ESG scr
6 EPG
DTV
Pr
7 DTV
Pr
watching other input sour
versa.
\(This button will not work if you wer
watching DTV immediately befor
tur
any other input sour
using the  button.\)
8 (Sound mode)
Select the sound multiplex mode.
\(See below
9	(k/l) (Volume)
	 \(k\) Incr
	 \(l\) Decr
10
 (Mute)
Switch the sound on and of
11 LIST
DTV
12 DTV MENU
DTV
13a/b/c/d (Cursor)
Select a desir
scr
14 END
Exit the menu scr
15 DEMO
Demonstrate the 100Hz \(tr

						

							11
MENU    [
Option ... 
Colour System]
Option
Audio Only
DNR
Input Select
Colour System
[Off]
[CVBS]
[AUTO]
Menu operations
On-Screen Display
Example
1Item displayed in white
• This indicates an item can be selected.
2Item displayed in yellow
• This indicates the item currently selected.
3Item in brackets
• This indicates the current setting for the item.
4Item with 
 displayed in grey
• This indicates the item cannot be selected for various
reasons.
NOTE
• Menu options differ in the selected input modes, but the
operating procedures are the same.
• The screens in the operation manual are for explanation
purposes (some are enlarged, others cropped) and may
vary slightly from the actual screens.
Menu operation buttons
Use the following buttons on the remote control unit to
operate the menu.
MENU:Press to open or close the menu screen.
a/b/c/d:Press to select a desired item on the screen
or adjust a selected item.
OK:Press to go to the next step or complete the
setting.
RETURN:Press to return to the previous step.
DTV MENU:Press to open or close the DTV Menu screen.
END:Press to exit the menu item.
1
2
3
4
LC-32RD2E_GB_b07.2.1, 5:15 AM 11

Teletext function
What is Teletext?
Teletext broadcasts pages of information and
entertainment to specially equipped television sets.
Your TV receives Teletext signals broadcast by a TV
network, and decodes them into graphical format for
viewing. News, weather and sports information, stock
exchange prices and programme previews are among
the many services available.
Turning on and off Teletext
1Select a TV channel or external input source
providing the Teletext programme.
2Press m to display the Teletext.
3Press m again to display the Teletext on the right
screen and normal image on the left screen.
• Each time you press m, the screen switches as
shown below.
* May appear in DTV input mode.
• If you select a programme with no Teletext signal,
“No Teletext available.” displays.
• The same message displays during other modes if
no Teletext signal is available.
NOTE
• Teletext will not work if the selected signal type is RGB.
(See page 19.)
TELETEXT
TELETEXT
Time display
You can display the time information included in the
DTV and Teletext broadcasts.
NOTE
• Skip step 1 if receiving DTV broadcasts.
1Select a TV channel providing Teletext information.
(The time information is automatically captured.)
2Press p. The channel display will appear on the
TV.
3Press p again within the several seconds that
the channel display is on the screen.
Time information will display below the channel
display for several seconds.
4Even when you change the TV channel, you can
display the time information with steps 2 and 3
above.
NOTE
• The time display cannot be stored once the power is
turned off. When you turn on the power, perform steps 1
to 4 again.
• If acquired successfully, the time information will appear
in the upper-right corner of the screen by pressing MENU.
Still image
You can freeze a motion picture on the screen.
1Press 3.
2Press 3 again to exit still image.
NOTE
• When this function is not available, “No still image display
available.” will display.
• The still image automatically goes out after 30 minutes.
Useful features
Description
Increase or decrease the page number.
Select a group or block of pages displayed
in the coloured  brackets at the bottom of the
screen by pressing the corresponding
Colour (Red/Green/Yellow/Blue) on the
remote control unit.
Directly select any page from 100 to 899 by
using 0–9.
Switch the Teletext image to Top, Bottom or
Full.
Reveal or hide hidden information such as
an answer to a quiz.
Stop updating Teletext pages automatically
or release the hold mode.
Display the subtitle or exit the subtitle
screen.
• Subtitle will not be displayed when the
service does not contain the subtitle
information.
User for LC-32RD2E, LC-37RD2E,
LC-42RD2E:
• Subtitle is set to off when the power is
turned on.
User for LC-32RD2S, LC-37RD2S,
LC-42RD2S:
• Subtitle is set to on when the power is
turned on.
Reveal or hide subpages.
• Red button: Move to the previous subpage.
• Green button: Move to the following subpage.
• These two buttons are shown on the screen
by the signs l and k. Buttons
P (r/s)
Colour (Red/
Green/Yellow/
Blue)
0–9
v (Top/
Bottom/Full)
k (Reveal
hidden
Teletext)
3 (Freeze/
Hold)
[ (Subtitle
for Teletext)
1 (Subpage)
Button functions
DATA*
LC-32RD2E_GB_c07.2.1, 5:16 AM 21
 
						

							6
Remote control unit
Quick guide
117
18
19
20
21
22
23
24
25
26
27
29 28
30
31
32
33 4
5
15
166
7
8
9
10
11
12
13
143 2
1[m(Teletext)
Select the TELETEXT mode. \(All TV
image, DTV/DA
image, TV/TEXT image\) \(See pages 21
and 31.\)
DTV
TELETEXT
22 (Standby/On)
Enter standby mode or tur
power
3p (Freeze/Hold)
\(See page 21.\)
4b (Subpage)
\(See page 21.\)
5s (Flashback)
Pr
in nor
while operating in EPG/ESG scr
6 EPG
DTV
Pr
7 DTV
Pr
watching other input sour
versa.
\(This button will not work if you wer
watching DTV immediately befor
tur
any other input sour
using the r button.\)
8B (Sound mode)
Select the sound multiplex mode.
\(See below
9	m(k/l) (Volume)
	 \(k\) Incr
	 \(l\) Decr
10
 (Mute)
Switch the sound on and of
11 LIST
DTV
12 DTV MENU
DTV
13a/b/c/d (Cursor)
Select a desir
scr
14 END
Exit the menu scr
15 DEMO
Demonstrate the 100Hz \(tr

						

							23
DTV menu operations
About using the character set screen
In some cases you may be prompted to enter
characters. See below for details.
Sample Alpha Numerical Character Set screen
Alpha Numerical Character Set
OKEND
Select
FAV
!~#$%&‘ ( ) *
+ , - . / 012345
6789 ; : ?@
ABCDEFGH I J K
LMNOPQRS T UV
WXYZ[ \ ]^`=a
bcde f gh i j k l
mnopq r s t uvw
xyz
0...9
1Input area
2Space
To add or overwrite with a space.
3Character select area
4YELLOW (Select) button
Press to move between the input area and character
select area.
5a/b/c/d button
Press to move the cursor.
6OK button
While in the input area:
Confirms the new name.
Once OK is pressed to confirm, a confirmation
message displays.
Press c/d to select “Yes”, and then press OK.
While in the character select area:
Confirms the input of a character.
Programme Setup
Configure various settings for each service. Press the
preassigned 
 -  numeric buttons to access each
of the functions explained below.
Press OK while the cursor is on “Programme
Setup”.
Sample Programme Setup screen
Programme Setup
S.No Services
001 BBC
002 BBC News
003 BBC 1
004 BBC 2Lock SkipEraseMoveFav
1
1. Fav
3. Move
5. Skip
7. Erase
9. View2. Lock
4. Move To
6. Select
8. Label
Select0...9OKENDRADIODTV MENUTV/Radio
Basque
Catalan
Croatian
Czech
Danish
Dutch
English*
Finnish
French
Gaelic*
Gallegan
GermanGreek
Italian
Norwegian
Polish
Portuguese
Russian
Serbian
Slovak
Spanish
Swedish
Turkish
Welsh*
Available language list
* Languages available for MHEG5 service
Language
Select language settings for audio (if a programme is
broadcast in more than one language) and MHEG5
service.
1Press OK while the cursor is on “Language”.
2Press a/b to select “1st Pref. Audio”, “2nd Pref.
Audio”, “3rd Pref. Audio” or “MHEG”.
3Select a desired language for each item.
NOTE
• See page 18 to change the language displayed on-screen.
• See page 31 to change the subtitle language.
• See page 31 for details on the MHEG5 service.
NOTE
• The picture window shows a blank image if Radio services
are listed.
Sample operation using Alpha Numerical Character
Set
1Call up the character set screen while in the
“Label” or “Carrier Setup” screen. (See pages 25
and 26.)
2Press YELLOW (Select) to move the cursor to
the character select area.
3Press a/b/c/d to select the desired character,
and then press OK. Repeat until the new name is
fully entered.
• Use space to add a space or overwrite.
4To register the new name, press YELLOW
(Select) to move the cursor back to the input area.
5Press OK.
• A confirmation message displays.
6Press c/d to select “Yes”, and then press OK. 1
3
5
6 4 2
LC-32RD2E_GB_d07.2.1, 5:18 AM 23
 
						

							24
DTV menu operations
Favourite
Assign services to 4 different favourite groups.
1Press a/b to select the desired service.
2Press  on the remote control. A selection box
displays.
3Press a/b to register the selected service to any
of the 4 favourite groups (None, Fav 1 ... Fav 4)
and then press OK. An icon displays indicating
the favourite status.
• Do not press END to exit the screen here if you wish
to register the change.
4Press OK.
5Now you can easily select your favourite service
from the Programme List. (See page 30.)
NOTE
• You cannot register the same service to two different
favourite groups.
Move
Sort the order of the selected service by moving the
service position.
1Press a/b to select the desired service.
2Press  on the remote control. An icon displays
indicating the service to be moved.
• Pressing  will turn the move icon on and off.
3Move the selected service to the desired position
using a/b, and then press OK.
• Do not press END to exit the screen here if you wish
to register the change.
4Press OK to register the change.
Lock
When the service is locked, you must enter your PIN
whenever you tune to the service.
1Press a/b to select the desired service.
2Press  on the remote control.
If you have already set the PIN, enter it here. If
not, enter the factory preset PIN “1234”.
An icon displays indicating the service is locked.
• Pressing  will turn the lock icon on and off. (PIN
entry is required when lifting the lock icon.)
• Do not press END to exit the screen here if you wish
to register the change.
3Press OK.
NOTE
• See page 17 for setting the PIN.
Move To
Use this function to change the position of two selected
services.
1Press a/b to select the desired service.
2Press  on the remote control.
3Enter the number you want to change to using
 -  numeric buttons, and then press OK. The
positions of the selected services are switched.
• Do not press END to exit the screen here if you wish
to register the change.
• You cannot enter a service number that is not listed.
4Press OK again, the message “Successfully
updated” displays. The change is now registered.
Skip
Services that are set to skip will not be picked up when
pressing P (s/r).
1Press a/b to select the desired service.
2Press  on the remote control. An icon displays
indicating the service to be skipped.
• Pressing  will turn the skip icon on and off.
• Do not press END to exit the screen here if you wish
to register the change.
3Press OK.
NOTE
• To view services that are set to be skipped, use  - 
numeric buttons or select from the Programme List.
EXAMPLE:
Moving “002 ZDF” ahead of “001 ARD”.
Default order: Press a/b to select the desired service in
001rs002rs003rs004.
Sorted order: Press a/b to select the desired service in
002rs001rs003rs004.
s ss s
ss ss s
s
002 ZDF
001 ARD
003 SAT. 1
004 RTL001 ARD
002 ZDF
003 SAT. 1
004 RTL
001 ZDF
002 ARD
003 SAT. 1
004 RTL001 RTL
002 ARD
003 SAT. 1
004 ZDF
LC-32RD2E_GB_d07.2.1, 5:18 AM 24

A. Information on Disposal for Users (private households)
1. In the European Union
Attention:
Used electr
requires proper treatment, reco
F
electr
retailer ma
*\) Please contact y
If y
bef
By disposing of this product correctly y
reco
could otherwise ar
2. In other Countries outside the EU
If y
F
don’t purchase a ne
www
B. Information on Disposal for Business Users
1. In the European Union
If the product is used f
Please contact y
f
local collection f
F
products
2. In other Countries outside the EU
If y
disposal.
Attention:
is mark
symbol. It means that
used electr
electronic products
should not be mix
with gener
w
separ
system f
products
LC-32RD2E_GB_f07.2.1, 5:21 AM 36
 
						

							25
Label
Change individual service names.
1Press a/b to select the desired service.
2Press  on the remote control. A character set
screen displays.
3Enter new name for the service. See page 23 for
operations using the character set screen.
Erase
Erase the selected service(s) from the memory.
1Press a/b to select the desired service.
2Press  on the remote control. An icon displays
indicating the service to be erased.
• Pressing  will turn the erase icon on and off.
• Do not press END to exit the screen here if you wish
to register the change.
3Press OK.
• A confirmation message displays.
4Press c/d to select “Yes”, and then press OK.
View
Tune to the service shown in the picture window.
1Press a/b to select the desired service.
2Press  on the remote control.
• The image shown in the picture window changes.
3Press END to exit the Programme Setup screen
to view the image in full screen.
DTV menu operations
Installation
This section describes how to reconfigure the DTV
settings after conducting Initial auto installation
(DTV) on page 8.
Carrier Scan
Manually add a new carrier by entering the desired
carrier number or frequency band.
1Press c/d to select “Installation”.
2Press a/b to select “Carrier Scan”, and then
press OK.
If you have already set the PIN, enter it here. If
not, enter the factory preset PIN “1234”.
Auto Installation
The TV automatically detects and stores all available
services in your area. See Initial auto installation
(DTV) on page 8 for details.
NOTE
• If the TV detects a new carrier/service that has become
available after performing “Auto Installation”, the message
“Do you want to save?” displays.
Press c/d to select “Yes” or “No”, and then press OK.
Carrier Scan
Select
35
554000 Channel
Frequency (kHz)
0...9OKENDDTV MENU
3Press a/b to select “Channel”, then c/d to enter
the carrier number, and then press OK.
• The frequency of the selected carrier in the below
cell changes correspondingly.
4After the scan is complete, the screen shows all
available services for the selected range.
5A confirmation message displays. Press c/d to
select “Yes”, and then press OK to save the
change.
NOTE
• You can directly enter the frequency instead of step 3. In
this case, select “Frequency (kHz)”, enter the number
using 
 -  numeric buttons, and then press OK. Use
c/d to move between the digits.
• After performing “Carrier Scan”, the order stored by using
the “Move” function will revert to the default order.
• See page 17 for setting the PIN.
Select
Use this function to jump to the specific service in one
step. This is useful when there are many services
displayed on screen to scroll through.
1Press  on the remote control. Now you can
change the service number on the left side of the
screen.
2Enter the number using  -  numeric buttons,
and then press OK. The highlight moves to the
selected service.
LC-32RD2E_GB_d07.2.1, 5:18 AM 25
 
						

							26
DTV menu operations
Carrier Setup
This is provided for you to rename (label), erase, or
re-scan carriers. “Carrier” in this context refers to a
service station that provides a set of individual
services.
1Press c/d to select “Installation”.
2Press a/b to select “Carrier Setup”, and then
press OK.
If you have already set the PIN, enter it here. If
not, enter the factory preset PIN “1234”.
Carrier Setup
S.No Carrier Name
001Frequency TV Radio
BBC 538000 05 03
002 BBC 546000 06 08
003 Canal+ 554000 04 00
004 Digital5 592500 06 02
Select
OKENDDTV MENU
LabelEraseRescan
System Setup
Configure On-Screen Display and Child Lock settings.
OSD Setup
The On-Screen Display appearance and the position/
duration of the service banner information can be
customised.
1Press c/d to select “System Setup”.
2Press OK.
OSD Setup
SelectOKENDDTV MENU
4 Secs
Bottom
20% Banner timeout
Banner position
Transparency
Selectable items
1 Sec/2 Secs/
... 7 Secs/None
Top/Bottom
None/10%/20%/
...50% OSD Setup
items
Banner
timeout
Banner
position
TransparencyDescription
Select how long the service
banner information
appears on screen.
Select whether the service
banner information
appears on top or bottom
of the screen.
Select the desired level of
On-Screen Display
transparency.
1To rename the selected carrier:
Select the carrier, and then press RED (Label).
The character set screen displays.
Enter a new name for the carrier. See page 23 for
details on using the character set screen.
2To erase the selected carrier:
Select the carrier, and then press GREEN (Erase).
An icon displays indicating the carrier to be erased.
Pressing GREEN will turn the erase icon on and off.Press OK.
A confirmation message displays.
Press c/d to select “Yes”, and then press OK.
3To re-scan the selected carrier:
Select the carrier, and then press BLUE (Rescan).
Re-scanning starts.
A confirmation message displays.
Press c/d to select “Yes”, and then press OK.
NOTE
• After re-scanning the selected carrier, the order stored
by using the “Move” function will revert to the default order.
3Press a/b to select the desired item.
4Press c/d to select the desired parameter, and
then press OK.
5A confirmation message displays. Press c/d to
select “Yes”, and then press OK to save the
change.
LC-32RD2E_GB_d07.2.1, 5:18 AM 26
 
						

							27
DTV menu operations
Child Lock
This function allows TV and Radio services to be
restricted. It prevents children from watching violent
or sexual scenes that may be harmful.
1Press c/d to select “System Setup”.
2Press a/b to select “Child Lock”, and then press
OK.
3If you have already set the PIN, enter it here. If
not, enter the factory preset PIN “1234”.
4Press c/d to select the desired age/rating (4
...18/Universal/Parental/X-rated/None), and then
press OK.
NOTE
• “Universal” and “Parental” are the ratings used exclusively
in France.
• “X-rated” is the rating used exclusively in Spain.
• For details about ratings see page 34.
Auto upgrade
1When you tune to the service that provides the
upgrade via Over Air Download, a confirmation
message displays.
2Follow the screen prompts.
3Check the new software version number to confirm
the successful upgrade.
NOTE
• To scan all carriers for upgrade availability, perform the
manual upgrade.
• The software upgrade may take about 30 minutes, but
may take longer (up to 1 hour) depending on the signal
status. While updating, you cannot switch to TV or external
input mode or enter standby mode using B on the remote
control unit.
CAUTION
•Do not disconnect the AC cord when the software
upgrade is in progress, as this may cause the upgrade
to fail. If problem arises ask a qualified service
personnel before the software upgrade period expires.
Accessories
Check the version information of the digital module
and allow it to be upgraded (when available).
Software Version
1Press c/d to select “Accessories”.
2Press OK.
• The software version is displayed.
Software Upgrade
The software for controlling the built-in DTV decoder
can be upgraded when necessary. In Great Britain this
can be achieved via an Over Air Download.
Preparation
Confirm and make a note of the current software
version number as in step 2 of Software Version.
Manual upgrade
1Press c/d to select “Accessories”.
2Press a/b to select “Software Upgrade”, and
then press OK. The TV checks all carriers if there
is a new software available for upgrade.
1If upgrade via Over Air Download is available at
the time:
A confirmation message appears asking you to
accept the upgrade or not.
To download now, press c/d to select “Yes”, and
then press OK. After the upgrade is completed,
the TV restarts automatically with the new software
version installed.
To postpone the download, press c/d to select
“No”, and then press OK. Enter the download time
for more convenient time as instructed.
The software upgrade will not be carried out if there
is no new software available at the specified
download time.
2If upgrade via Over Air Download is NOT
available at the time:
A message tells you that there is no software
available to be downloaded.
3Check the new software version number to confirm
the successful upgrade.
Child Lock
Select
7 Age/Rating
OKENDDTV MENU
LC-32RD2E_GB_d07.2.1, 5:18 AM 27
 
						

							28
DTV menu operations
Inserting a CA card
A single DVB Common Interface (CI) will be
implemented to allow adoption of a Conditional Access
(CA) system by means of a plug-in CA module.
Scrambled Broadcasting service can be routed via the
CA system.
If the CA system on the CI module requires a smart-
card reader, this reader shall be part of the CI module.
When the compatible CA card is inserted, you can
view the programme without any operations.
Supplying power to the antenna
You may choose to supply power through the antenna
terminal. (See page 4.)
NOTE
• This function is enabled using the Analogue Menu. See
page 18 for details.
When the compatible card is not inserted:
1Select the programme which needs the compatible
CA card.
• The caution screen appears.
2Insert the compatible CA card.
• The caution screen disappears and you can view
the programme.
CA system supported by:
Crypto Works
Aston CAM
VIAccess
Nagra Vision
Irdeto
MR CAM
NOTE
• To view paid TV broadcasting, you need to make a contract
with a service provider.
Please contact a service provider for details.
• The Common Interface Module and the CA card are
neither supplied nor optional accessories.
Common Interface
Check the detailed information on the Common
Interface module card in use.
1Press OK while the cursor is on “Common
Interface”.
• The CI module name is displayed.
CI Module
IRDETO Module Name
OKENDDTV MENU
2Press OK to access the CI menu.
• Detailed information on the CI card in use is
displayed.
3Press a/b to select the item, and then press OK.
• Detailed information on the selected item is
displayed.
Common Interface ModuleCA card
LC-32RD2E_GB_d07.2.1, 5:18 AM 28