Sharp Lc 40le705 Operation Manual

							9
Initial auto installation
When the TV is powered on for the first time after 
purchase, the initial auto installation wizard appears. 
Follow the menus and make the necessary settings one 
after another.
Confirm the following before turning on 
the power
Is the antenna cable connected?
Is the AC cord plugged in?
Is the MAIN POWER switch turned on (;)?
E
E
E
Press a on the TV.The initial auto installation wizard appears.
Setting the OSD language.
Press a/b/c/d to select the desired language, 
and then press ;.
Selecting the location of the TV.
HOMESTORE
Press c/d to select where you will use this TV, 
and then press ;.
HOME: “STANDARD” will be the default value for the “AV 
MODE” setting.
STORE: “DYNAMIC (Fixed)” will be the default value for 
the “AV MODE” setting. If the “AV MODE” is changed, 
the TV will automatically switch back to “DYNAMIC 
(Fixed)” when there is no signal input from the TV or 
remote control unit for 30 minutes.
A demonstration image will be displayed after initial auto 
installation is completed. If you have chosen “STORE” by 
mistake, go to “Setup” > “Reset” > select “HOME” again\
.
Setting the country.
Austria
Finland
Greece
Press a/b/c/d to select your country or area, 
and then press ;.
This setting screen only appears during the first 
installation.
1•
2
3
•
•
•
4
•
NOTEIf you set “Sweden” in the country setting, you can select 
the cable provider “ComHem”. Refer to the H mark 
in the following steps or instructions about the settings for 
“ComHem”.
Starting channel search.
Digital searchAnalogue search
Press c/d to select “Digital search” or “Analogue 
search”, and then press ;.
To watch both analogue broadcasts and digital 
broadcasts, you should perform the auto installation 
setting for each format (Page 27).
If you want to search for more broadcasts, execute 
“Additional search” from the “Programme setup” menu 
(Pages 27_29).
NOTEIf you turn off the power on the TV while performing a channel 
search, the initial auto installation wizard will not appear. The 
auto installation function allows you to execute the installation 
again from the “Setup” menu (Page 27).
The initial auto installation wizard will abort if you leave the TV 
unattended for 30 minutes before searching for channels.
After initial auto installation is completed, the default PIN is 
automatically set to “1234”. To change the PIN setting, refer to 
Password/Parental lock settings (Page 30). To clear the PIN 
setting (PIN input will no longer be needed), refer to CLEARING 
THE PIN (Page 41).
When “Italy” is selected in the country setting, the default age 
restriction value is set to 18.
Digital broadcast setting
Press c/d to select “Terrestrial” or “Cable”, 
and then press ;.
TerrestrialCable
HWhen you set “Sweden” in the country setting and select 
“Cable” for the searching format, you can select the 
cable provider “ComHem”.
Searching for terrestrial broadcasts
The TV searches for, sorts and stores all the 
receivable TV stations according to their 
settings and the connected antenna.
To abort the initial auto installation in progress, press 6.
•
5
•
•
•
•
•
•
•
E
•
Quick guide
LC-LE705E_GB.indd   9 LC-LE705E_GB.indd   9 2009/10/09   14:12:57
2009/10/09   14:12:57
 
						

							10
Quick guide
Searching for cable broadcasts
To change each item to the appropriate 
settings:
Press a/b to select the menu, and then 
press ;.
Scrambled stations[Yes]
[Channel]
[None]
Search method
Start frequency
Network ID
Symbol rate 1
Symbol rate 2
QAM modulation 1
QAM modulation 2
Reset
Search start
Press a/b/c/d or 0_9 to select or input 
the appropriate item/value, and then press 
;.
Press a/b to select “Search start”, and then 
press ;.
The TV searches for, sorts and stores all 
the receivable TV stations according to their 
settings and the connected antenna.
To abort the initial auto installation in progress, press 6.
HThe “Scrambled stations” menu and the “Search method” 
menu are not displayed on the screen as each menu item is 
fixed.
The value of “Start frequency” and “Network ID” should be set 
to the value specified by the cable provider.
E
1
2
3
4
•
•
•
Menu Description Selectable items
Scrambled 
stations Specifies if you 
need to add pay-TV 
services.
Yes, No
Search 
method Specifies how you 
search channels. Channel: Extracts all 
of information from a 
channel (quick, but 
needs corresponding 
TV stations).
Frequency: Checks 
every frequency in 
range (slow).
Start 
frequency From 47.0_858.0 
MHz
Network ID Specifies the network. 
Set this to register 
only the specified 
network ID without 
registering any special 
services.
None, 0_65535
Symbol 
rate 1* The symbol rates 
are specified by the 
cable provider. Input 
the value received for 
CATV.
1000_9000
Symbol 
rate 2* The symbol rates 
are specified by the 
cable provider. Input 
the value received for 
CATV.
1000_9000
QAM 
modulation 1 16, 32, 64, 128, 256
QAM 
modulation 2 None, 16, 32, 64, 
128, 256
Set up “Symbol rate 2” if the cable provider uses several 
symbol rates.
HWhen you set “Sweden” in the country setting and select 
“Cable” for the searching format, you can select the cable 
provider “ComHem”. Follow the screen prompts.
Analogue broadcast setting
The TV searches for, sorts and stores all the 
receivable TV stations according to their 
settings and the connected antenna.
To abort the initial auto installation in progress, press 6.
*
•
•
LC-LE705E_GB.indd   10 LC-LE705E_GB.indd   10 2009/10/09   14:12:58
2009/10/09   14:12:58
 
						

							11
Quick guide
Checking signal strength and 
channel strength (DVB-T/C)
If you install a DVB-T/C antenna for the first time or 
relocate it, you should adjust the alignment of the 
antenna to receive a good reception while checking the 
antenna setup screen.
Go to “MENU” > “Setup” > “Antenna setup-
DIGITAL”.
Checking signal strength
Press a/b to select “Signal strength”, and 
then press ;.
Supply voltageCH no.
CurrentMax.
Signal strengthSignal strength
Channel strength
CurrentMax.
Quality
Checking channel strength
Press a/b to select “Channel strength”, and 
then press ;.
You can input a specified frequency band using the 0_9 
numeric buttons.
E
E
•
Channel strength of DVB-T
Supply voltage
CH no.
CurrentMax.
Signal strengthMHz
Signal strength
Channel strength
CurrentMax.
Quality
Channel strength of DVB-C
Supply voltage
Current
Max.
Signal strengthMHz
Signal strength FrequencySymbol rateQAM modulationChannel strength
CurrentMax.
Quality
Position and align the antenna so that 
the maximum possible values for “Signal 
strength” and “Quality” are obtained.
NOTEThe values of “Signal strength” and “Quality” indicate when to 
check the appropriate alignment of the antenna.
4
•
Inserting the CA card into the CI module
In order to receive coded digital stations, a common interface module (CI module) a\
nd a CA card must be inserted in the 
CI slot of the TV.
Carefully insert the CI module in 
the CI slot with the contact side 
forward.
The logo on the CI module must 
be facing outward from the rear 
of the TV.
1
2
Checking CI module information
Go to “MENU” > “Digital setup” > “CI menu”.This menu is only available for digital stations.
The content of this menu depends on the provider of the CI module.
Module
General information on CI module displays.
Menu Adjustment parameters of each CA card displays.
Enquiry You can input numerical values such as passwords here.
•
•
NOTEOnly the LC-32LE705E, LC-32LE705S, LC-40LE705E, LC-40LE705S, LC-46LE705E\
, LC-46LE705S, LC-32LX705E, LC-40LX705E, LC-
46LX705E, LC-32LU705E, LC-32LU705S, LC-40LU705E, LC-40LU705S, LC-46LU705\
E and LC-46LU705S models are compatible with 
the Common Interface (CI) standard as well as the enhanced security Common Interface Plus (CI+) standar\
d.
It takes about 30 seconds to certify the license key when you insert a C\
A card into the CI+ compatible CI module for the first time. This 
process may fail when there is no antenna input or you have never run “Auto installation”.
The CI+ compatible CI module sometimes upgrades its firmware. You may not receive any TV images before upgrading. You can only use 
the power button during upgrading.
The CI+ compatible CI module does not allow you to output any copy protected programmes using monitor out. In this case, the copy 
protect icon* is shown in the programme information when P. INFO is pressed.
Protect icon: X
If the TV displays an update confirmation message for the CA card while receiving CI+ compatible broadcasts, follow the screen prompts.
Make sure that the CI module is properly inserted.
•
•
•
•
*
•
•
LC-LE705E_GB.indd   11 LC-LE705E_GB.indd   11
2009/10/09   14:12:58
2009/10/09   14:12:58
 
						

							12
Daily operation
Switching on/off
Turning on/off the power
Turn on (;) the MAIN POWER switch on the 
left side of the TV (Page 4).
Press a on the TV.
Switch it off by pressing a on the TV.
When turning off the power using a on the TV, EPG data 
will be lost.
Standby mode
To standby modeIf the TV is switched on, you can switch it to standby by 
pressing B on the remote control unit.
Switching on from standbyFrom standby, press B on the remote control unit.
TV indicator status
B (Standby/On indicator) Status
Off Power off
Green Power on
Red Standby
NOTEIf you are not going to use this TV for a long period of time, be 
sure to remove the AC cord from the AC outlet or turn off (a) 
the MAIN POWER switch on the left side of the TV (Page 4).
A small amount of electric power is still consumed even when 
a is turned off.
Switching between digital and 
analogue broadcasts
Watching digital 
broadcasts Watching analogue 
broadcasts
Changing channels
With :r/s
With 0_9
1
2
•
E
E
•
•
Selecting an external video 
source
Once the connection is made, 
press b to display the “INPUT 
SOURCE” screen, and then press 
b or a/b to switch over to 
the appropriate external source 
with ;.
EXT 2
INPUT SOURCE
TV
EXT 1
EXT 3
Selecting a sound mode
DTV modeIf multi sound modes are received, each time you press 
2 the mode switches as follows.
Audio (ENG) STEREO
L/R LRLR
CH A CH B CH AB
Audio (ENG) CH A
Audio (ENG) MONO
Press c/d to select L or R sound when the STEREO or 
DUAL MONO screen is displayed.
Audio (ENG) STEREO
L/R LRLR
NOTEThe sound mode screen disappears in six seconds.
Selectable items vary depending on the received broadcasts.
ATV modeEach time you press 2, the mode switches as shown 
in the following tables.
NICAM TV broadcasts selection
Signal Selectable items
Stereo NICAM STEREO, MONO
Bilingual NICAM CH A, NICAM CH B, NICAM CH AB, 
MONO
Monaural NICAM MONO, MONO
A2 TV broadcasts selection
Signal Selectable items
Stereo STEREO, MONO
Bilingual CH A, CH B, CH AB
Monaural MONO
NOTEWhen no signal is input, the sound mode will display “MONO”.
E
•
•
E
•
Watching TV
LC-LE705E_GB.indd   12 LC-LE705E_GB.indd   12 2009/10/09   14:12:59
2009/10/09   14:12:59
 
						

							13
Watching TV
EPG
EPG is a programme list that is displayed on the screen. With the EPG, you can check the schedule of DTV/RADIO/
DATA, view detailed information about them, tune to an event currently on-air.
Useful settings for using EPG
Basic operation
Press @ and the “MENU” screen 
displays.
Press c/d to select “Digital setup”.
Press a/b to select “EPG setup”, and then 
press ;.
Digital setup
REC picture size[16:9 TV]
Download setup [Yes]
EPG setup
Subtitle
CI menu
Press a/b to select the desired item, and 
then press ; (e.g., “EPG setup”, “Display 
range setup”, etc.).
EPG setup
Display range setup Receive broadcasting EPG 
automatically?
Genre icon setup
Ye sNo
Press a/b/c/d to select or adjust the 
desired item, and then press ; (e.g., “Yes”, 
“No”, etc.).
1
2
3
4
5
EPG display settings
EPG setup (setting for receiving EPG 
data)
If you want to use the EPG for digital stations, select 
“Yes”. The EPG data must be automatically captured 
while the TV is in standby mode. After setting to “Yes”, 
it may take some time to turn off the power using the 
remote control unit due to the process of the data 
capture.
NOTEIf the MAIN POWER switch or the power button on the TV are 
switched off, the EPG data will not be captured.
Display range setupThe “Display range setup” allows you to select three 
types of time spans for display on the screen.
Item
Mode 1 (Wide 
angle) Displays six hours of programme 
information.
Mode 2 (Zoom) Displays three hours of programme 
information.
Mode 3 (Vertical 
angle) Changes to the EPG display format with 
a vertical time span.
Genre icon setupYou can grey out or place a mark on desired genres and 
smoothly search for programmes you frequently watch.
Genre icon list
Icon Genre Icon Genre
Movie/DramaMusic/Ballet/Dance
News/Current 
affairsArts/Culture 
(without music)
Show/Game showSocial/Political 
issues/Economics
SportsEducation/Science/
Factual topics
Children’s/Youth 
programmesLeisure hobbies 
E
•
E
E
E
LC-LE705E_GB.indd   13 LC-LE705E_GB.indd   13
2009/10/09   14:13:00
2009/10/09   14:13:00
 
						

							14
Selecting a programme using EPG
Basic operation
The illustrations on this page are explained 
using three digit services.
Display/Close the EPG 
screen
Press EPG.
E
SelectEnterBackExit
AMPM
Programme info. Search by genre Search by date
Select a programmeSelect the time span
Press c/d to select the time span you want 
to search.
Continue to press d to display programmes in the next 
time span.
E
1
•
Select the desired programme
Press a/b to select the desired programme.If a or b are displayed on the left of the services, 
continue to press a/b to display next or previous 
screen.
2
•
Useful functions
Check programme information
Press a/b/c/d to select the programme you want to check.
Press R, and then press ; to tune to the selected programme.
Search a programme in a category
Press G.
Press a/b to select the desired genre, and then press ;.
Press a/b to select a programme you want to watch, and then press 
;.
Refer to page 13 for the genre setting.
4
1
2
3
•
News/Current affairs Movie/Drama
Show/Game show
Sports
Children’s/Youth programmes
Music/Ballet/Dance
Search for a programme by date/time
Press Y.
Press c/d to select the desired time span, and then press ;.
Back to EPG
EnterSelect time
Search by time
Enter +1 Week NextTo d a y
0 AM - 6 AM 6 AM - 0 PM0 PM - 6 PM 6 PM - 0 AM Next
Press a/b to select the desired programme, and then press ;.
3
1
2
5
1
2
3
Watching TV
LC-LE705E_GB.indd   14 LC-LE705E_GB.indd   14
2009/10/09   14:13:01
2009/10/09   14:13:01
 
						

							15
Teletext
What is teletext?Teletext broadcasts pages of information and 
entertainment to specially equipped TV. Your TV receives 
teletext signals broadcast by a TV network, and decodes 
them into graphical format for viewing. News, weather 
and sports information, stock exchange prices and 
programme previews are among the many services 
available.
Turning teletext on/off
Select a TV channel or external source 
providing a teletext programme.
Press m to display the teletext.
Many stations use the TOP operating system, while 
some use FLOF (e.g., CNN). Your TV supports both 
these systems. The pages are divided into topic groups 
and topics. After switching on the teletext, up to 2,000 
pages are stored for fast access.
If you select a programme with no teletext signal, “No 
Teletext available” displays.
The same message displays during other modes if no 
teletext signal is available.
TELETEXTTELETEXT
Each time you press m, the screen switches as shown 
above.
Press m again to display the teletext on the right screen 
and the normal image on the left screen.
NOTETeletext will not work if the selected signal type is RGB (Page 
34).
1
2
•
•
•
•
•
•
Buttons for teletext operations
Buttons Description
:r/s Increase or decrease the page number.
Colour (R/G/
Y/B) Select a group or block of pages displayed 
in the coloured brackets at the bottom of 
the screen by pressing the corresponding 
colour (R/G/Y/B) on the remote control 
unit.
Numeric 
buttons 0_9 Directly select any page from 100 to 899 
by using the 0_9 numeric buttons.
v (Top/
Bottom/Full) Switch the teletext image to top, bottom 
or full.
k (Reveal 
hidden teletext) Reveal or hide hidden information such as 
an answer to a quiz.
3 (Freeze/
Hold) Stop updating teletext pages automatically 
or release the hold mode.
[ (Subtitle for 
teletext) Display the subtitle or exit the subtitle 
screen.
Subtitles will not be displayed when 
the service does not contain subtitle 
information.
•
1 (Subpage)
Reveal or hide subpages.Move to the previous subpage (R).
Move to the following subpage (G).
These two buttons are shown on the 
screen by the symbols “e” and “f”.
•
•
•
Using the MHEG-5 application 
(UK only)
Some services bring you programmes with the MHEG 
application encoded, letting you experience DTV 
interactively. When provided, the MHEG-5 application will 
start when you press m.
Watching TV
LC-LE705E_GB.indd   15 LC-LE705E_GB.indd   15
2009/10/09   14:13:02
2009/10/09   14:13:02
 
						

							16Before connecting ...
Be sure to turn off the TV and any devices before making any connections.
Firmly connect a cable to a terminal or terminals.
Carefully read the operation manual of each external device for possible connection types. This also helps you get the be\
st possible 
audiovisual quality to maximise the potential of the TV and the connecte\
d device.
Refer to page 37 for connecting a PC to the TV.
NOTEThe cables illustrated in pages 16_18 are commercially available items.
Video connections
HDMI connection
Example of connectable devicesDVD player/recorder
Blu-ray player/recorder
Game console
E
E
E
The HDMI connections permit digital video and 
audio transmission via a connection cable from a 
player/recorder. The digital picture and sound data are 
transmitted without data compression and therefore lose 
none of their quality. Analogue/digital conversion is no 
longer necessary in the connected devices, which also 
would result in quality losses.


HDMI-certified cable
ø 3.5 mm stereo minijack cable
DVI/HDMI cable


DVI/HDMI conversionUsing a DVI/HDMI cable, the digital video signals of 
a DVD can also be played via the compatible HDMI 
connection. The sound must be fed in additionally.
When connecting a DVI/HDMI cable to the HDMI terminal, the 
image may not come in clearly.
Both HDMI and DVI use the same HDCP copy protection 
method.
When using the HDMI 2 terminalYou must set the audio signal input source 
depending on the type of HDMI cable connected 
(refer to page 25 for details).
HDMI-certified cable
Go to “MENU” > “Option” > “PC audio 
select” > select “EXT 4 (RGB)”.
DVI/HDMI cable
Go to “MENU” > “Option” > “PC audio 
select” > select “HDMI 2”.
E
NOTEIf a connected HDMI device is AQUOS LINK compatible, 
you can take advantage of versatile functions (Pages 
19_21).
Video noise may occur depending on the type of HDMI cable 
used. Make sure to use a certified HDMI cable.
When playing the HDMI image, the best possible format for the 
picture will be detected and set automatically.
Supported video signal576i, 576p, 480i, 480p, 1080i, 720p, 1080p
See page 38 for PC signal compatibility.
•
•
•
•
•
E•
•
•
•
•
Connecting external devices
LC-LE705E_GB.indd   16 LC-LE705E_GB.indd   16
2009/10/09   14:13:02
2009/10/09   14:13:02
 
						

							17
SCART connection
Example of connectable devicesDecoder
E

Decoder
SCART cable

Example of connectable devicesVCR
DVD player/recorder
E
E
If your VCR supports TV-VCR advanced AV Link 
systems, you can connect the VCR using a fully wired 
SCART cable.


VCR Decoder
SCART cable

NOTEIn cases when the decoder needs to receive a signal from the TV, make sure to select the appropriate input terminal to which the decoder 
is connected in “Manual adjust” in the “Analogue setting” me\
nu (Page 29).
TV-VCR advanced AV Link systems may not be compatible with some external sources.
You cannot connect the VCR with decoder using a fully wired SCART cable when selecting “Y/C” under “EXT 2” in the “Input \
select” 
menu.
Controlling devices with SCART using AV Link
This TV incorporates four typical AV Link functions for smooth connections between the TV and other audiovi\
sual 
equipment.
One touch play While the TV is in standby mode, it automatically turns on and plays back the image from the audiovisual 
source (e.g., VCR, DVD player/recorder).
TV standby When the TV enters standby mode, the connected audiovisual equipment (e\
.g., VCR, DVD player/
recorder) enters standby mode as well.
WYSIWYR When the remote control unit of the connected VCR has the WYSIWYR button, you can automatical\
ly 
start recording by pressing the WYSIWYR button.
Preset download Automatically transfers the channel preset information from the tuner on the TV to the one on the 
connected audiovisual equipment (e.g., VCR) via the EXT 2 terminal.
NOTERefer to the operation manuals of external equipment for details.
The AV Link function works only when audiovisual equipment is connected to th\
e EXT 2 terminal with a fully wired SCART cable.
The use of the AV Link function is only possible if the TV has enforced a complete auto installation with the connected audiovisual 
equipment (refer to Initial auto installation on page 9).
The availability of the AV Link function depends on the audiovisual equipment used. Depending on \
the manufacturer and type of 
equipment used, it is possible that the described functions may be compl\
etely or partially unusable.
When the TV receives a scrambled DTV signal, the WYSIWYR function may not work.
If the TV’s received signal is switched to a scrambled signal during recording with the WYSIWYR function, black images will be recorded 
in the external device.
•
•
•
•
•
•
•
•
Connecting external devices
LC-LE705E_GB.indd   17 LC-LE705E_GB.indd   17
2009/10/09   14:13:03
2009/10/09   14:13:03
 
						

							18
YPB
(CB)PR
(CR)Component connection
Example of connectable devicesVCR
DVD player/recorder
E
E
You will enjoy accurate colour reproduction and high 
quality images through the EXT 3 terminal when 
connecting a DVD player/recorder or other device.
YPB(CB)
L
RPR(CR)COMPONENT
AUDIO
 
Audio cableComponent cable
VIDEO connection
Example of connectable devicesVCR
DVD player/recorder
Game console
Camcorder
E
E
E
E
You can use the EXT 9 terminal when connecting to a 
game console, camcorder, a DVD player/recorder or 
other device.
\b
AV cable Audio connections
Speaker/amplifier connection
Connect an amplifier with external speakers as shown 
below.
Connecting an amplifier with digital/
analogue audio inputs
DIGITAL AUDIO  IN
	
AUX1 IN
LR


Optical audio cable (for digital audio input)
Audio cable (for analogue audio input)

After connecting
Digital audio output setting
After connecting an amplifier with digital audio 
input and external speakers as shown, you should 
set an audio output format compatible with 
the programme you are watching or the device 
connected.
Go to “MENU” > “Option” > “Digital 
audio output” > select “PCM” or “Dolby 
Digital”.
NOTEWhen set to “Dolby Digital”, Dolby Digital is output when 
the Dolby Digital or Dolby Digital Plus audio formats are 
received. When set to “PCM”, PCM is output no matter 
what audio formats are received.
E
•
E
Connecting external devices
LC-LE705E_GB.indd   18 LC-LE705E_GB.indd   18
2009/10/09   14:13:03
2009/10/09   14:13:03