Sharp Lc 32d44 Operation Manual

							1
IMPORTANT  :  Please read this operation manual before starting operating the equipment.
LC-32D44U
LC-37D44U
LIQUID CRYSTALTELEVISION
 
OPERATION MANUAL
ENGLISH
Supplied Accessories
Make sure the following accessories are provided with the product.
Remote control unit 
(g 1)
Page 7 “AA” size battery 
(g 2)
Page 8 AC cord
(g 1)
Page 7 Stand unit 
(g 1)
Page 6
Cable clamp 
(g 1)
Page 7 Operation manual 
(g 1)
To avoid scratching the frame or screen, please use a soft, lint free cloth for cleaning. Approved 
cleaning cloths are available directly from Sharp in single (00Z-LCD-CLOTH) or triple (00Z-LCD-
CLOTH-3) packs. Call 1-800 BE SHARP for ordering, or VISIT www.sharpusa.com/SharpDirect.
Always use the AC cord supplied with the TV.

The examples used throughout this manual are based on the LC-32D44U mode\
l.
LC-32D44U
LC-37D44U
- $  @ % 6 @& @ J O EE


-$@%6@&@JOEE


   


   



 
						

							2
IMPORTANT:
To aid reporting in case of loss or theft, please record 
the TVs model and serial numbers in the space 
provided. The numbers are located at the rear of the TV.Model No.:
Serial No.:
IMPORTANT INFORMATION
WARNING: 
TO REDUCE THE RISK OF FIRE OR ELECTRIC 
  SHOCK, DO NOT EXPOSE THIS PRODUCT TO 
  RAIN OR MOISTURE.
CAUTIONRISK OF ELECTRIC SHOCK 
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE
 SLOT, FULLY INSERT.
WARNING:  FCC Regulations state that any unauthorized changes or modifications t\
o this 
  equipment not expressly approved by the manufacturer could void the users authority 
  to operate this equipment.
CAUTION:  This product satisfies FCC regulations when shielded cables and connectors are used to 
  connect the unit to other equipment. To prevent electromagnetic interference with electric 
  appliances such as radios and televisions, use shielded cables and conne\
ctors 
 for connections. CAUTION:
DO NOT PLACE THIS PRODUCT ON AN UNSTABLE CART, STAND, TRIPOD, 
BRACKET, OR TABLE. THE PRODUCT MAY FALL CAUSING SERIOUS 
PERSONAL INJURY AND SERIOUS DAMAGE TO THE PRODUCT. USE ONLY 
WITH A CART, STAND, TRIPOD, BRACKET, OR TABLE RECOMMENDED BY 
THE MANUFACTURER OR SOLD WITH THE PRODUCT. FOLLOW THE 
MANUFACTURERS INSTRUCTIONS WHEN INSTALLING THE PRODUCT AND 
USE MOUNTING ACCESSORIES RECOMMENDED BY THE MANUFACTURER. 
A PRODUCT AND CART COMBINATION SHOULD BE MOVED WITH CARE. 
QUICK STOPS, EXCESSIVE FORCE, AND UNEVEN SURFACES MAY CAUSE
THE PRODUCT AND CART COMBINATION TO OVERTURN.
The lightning flash with arrow-head 
symbol, within an equilateral 
triangle, is intended to alert the 
user to the presence of 
uninsulated dangerous voltage 
within the products enclosure that 
may be of sufficient magnitude to 
constitute a risk of electric shock 
to persons.
The exclamation point within a 
triangle is intended to alert the 
user to the presence of important 
operating and maintenance 
(servicing) instructions in the 
literature accompanying the 
product.
Printed in MexicoTINS-D610WJZZ108P02-MX-NM
-
$  @ % 6 @& @ J O EE


-$@%6@&@JOEE


   


   



 
						

							3
Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of 
 Dolby Laboratories.
This product utilizes tin-lead solder, and uorescent lamp 
containing a small amount of mercury. Disposal of these 
materials may be regulated due to environmental considerations. 
For disposal or recycling information, please contact your local
authorities, the Electronic Industries Alliance: www.eiae.org, the 
lamp recycling organization: www.lamprecycle.org or 
Sharp at 1-800-BE-SHARP                           (For U.S.A. only)
Note to CATV system installer: This reminder is provided to call the CATV system installers attention to Article 820-40 of th e 
National Electrical Code that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall  
be connected to the grounding system of the building, as close to the point of cable entry as \
practical.
INFORMATION:
This equipment has been tested and found to comply with the limits for a\
 Class B digital device, 
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection 
against harmful interference in a residential installation. This equipment generates, uses and can 
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may 
cause harmful interference to radio communications. However, there is no guarantee that interference 
will not occur in a particular installation. If this equipment does caus\
e harmful interference to radio or 
television reception, which can be determined by turning the equipment off and on, the user is 
encouraged to try to correct the interference by one or more of the following measures:
  Reorient or relocate the receiving antenna.
  Increase the separation between the equipment and receiver.
  Connect the equipment into an outlet on a circuit different from that to which the receiver is 
 connected.
  Consult the dealer or an experienced radio/TV technician for help. DECLARATION OF CONFORMITY:
SHARP LIQUID CRYSTAL TELEVISION, MODEL LC-32D44U/LC-37D44U
This device complies with Part 15 of the FCC Rules. Operation is subject\
 to the following two 
conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
RESPONSIBLE PARTY:
  SHARP ELECTRONICS CORPORATION
  Sharp Plaza, Mahwah, New Jersey 07430-2135
 TEL: 1-800-BE-SHARP
For Business Customers: URL http://www.sharpusa.com
IMPORTANT INFORMATION
Trademarks
HDMI, the HDMI logo and High-Denition Multimedia Interface are trademarks or registered trademarks of 
  HDMI Licensing LLC.
Products that have earned the ENERGY STAR  are designed to protect the environment through superior 
 energy efciency.
- $  @ % 6 @& J O EC 


-$@%6@&JOEC


   


   



 
						

							4
Electricity is used to perform many useful functions, but it can also ca\
use personal injuries and property damage 
if improperly handled. This product has been engineered and manufactured with the highest priority on safety. 
However, improper use can result in electric shock and/or fire. In order to prevent potential danger, please 
observe the following instructions when installing, operating and cleani\
ng the product. To ensure your safety 
and prolong the service life of your Liquid Crystal Television, please read the following precautions carefully 
before using the product.1)  Read these instructions.
2)  Keep these instructions.
3)  Heed all warnings.
4)  Follow all instructions.
5)  Do not use this apparatus near water.
6)  Clean only with dry cloth.
7)  Do not block any ventilation openings. Install in accordance with the manufacturers instructions.
8)  Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including  amplifiers) that produce heat.
9)  Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades  with one wider than the other. A grounding type plug has two blades and a third grounding prong. The 
wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, 
consult an electrician for replacement of the obsolete outlet.
10)  Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles,  and the point where they exit from the apparatus.
11)  Only use attachments/accessories specified by the manufacturer.
12)  Use only with the cart, stand, tripod, bracket, or table specified by \
the manufacturer, or sold  with the apparatus. When a cart is used, use caution when moving the car\
t/apparatus 
combination to avoid injury from tip-over.
13)  Unplug this apparatus during lightning storms or when unused for long pe\
riods of time.
14)  Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been  damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects 
have fallen into the apparatus, the apparatus has been exposed to rain o\
r moisture, does not operate 
normally, or has been dropped.
Additional Safety Information
15)  Power Sources—This product should be operated only from the type of power source indicated on the  marking label. If you are not sure of the type of power supply to your home, consult your product dealer or 
local power company. For products intended to operate from battery power, or other sources, refer to the 
operating instructions.
16)  Overloading—Do not overload wall outlets, extension cords, or integral convenience receptacles as this  can result in a risk of fire or electric shock.
17)  Object and Liquid Entry—Never push objects of any kind into this product through openings as they may  touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill 
liquid of any kind on the product.
18)  Damage Requiring Service—Unplug this product from the wall outlet and refer servicing to qualified 
service personnel under the following conditions:a)  When the AC cord or plug is damaged,
b)  If liquid has been spilled, or objects have fallen into the product,
c)  If the product has been exposed to rain or water,
d)  If the product does not operate normally by following the operating instructions.\
  Adjust only those controls that are covered by the operating instructions as an improper adjustment  of other controls may result in damage and will often require extensive work by a qualified technician 
to restore the product to its normal operation,
e)  If the product has been dropped or damaged in any way, and
f)  When the product exhibits a distinct change in performance - this indicates a need \
for service.
19)  Replacement Parts—When replacement parts are required, be sure the service technician has used  replacement parts specified by the manufacturer or have the same characteristics as the original part. 
Unauthorized substitutions may result in fire, electric shock, or other hazards.
20)  Safety Check—Upon completion of any service or repairs to this product, ask the service technician to  perform safety checks to determine that the product is in proper operating condition.
21)  Wall or ceiling mounting—When mounting the product on a wall or ceiling, be sure to install the product 
according to the method recommended by the manufacturer.
DEAR SHARP CUSTOMER
Thank you for your purchase of the Sharp Liquid Crystal Television. To e\
nsure safety and many years 
of trouble-free operation of your product, please read the Important Saf\
ety Instructions carefully before 
using this product.
IMPORTANT SAFETY INSTRUCTIONS
-$  @ % 6 @& J O EC 


-$@%6@&JOEC


   


   



 
						

							5
IMPORTANT SAFETY INSTRUCTIONS
 Outdoor Antenna Grounding — If an outside antenna is connected to the television equipment, be sure the antenna 
system is grounded so as to provide some protection against 
voltage surges and built-up static charges.
  Article 810 of the National Electrical Code, ANSI/NFPA 70,  provides information with regard to proper grounding of the 
mast and supporting structure, grounding of the lead-in wire 
to an antenna discharge unit, size of grounding conductors, 
location of antenna-discharge unit, connection to grounding 
electrodes, and requirements for the grounding electrode.EXAMPLE OF ANTENNA GROUNDING AS PER 
NATIONAL ELECTRICAL CODE, ANSI/NFPA 70
ANTENNA 
LEAD IN WIRE
GROUND 
CLAMP
NEC — NATIONAL ELECTRICAL CODE
GROUNDING 
CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING 
ELECTRODE SYSTEM
(NEC ART 250, PART H)
ELECTRIC 
SERVICE 
EQUIPMENT
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
 Water and Moisture — Do not use this product near water - for example\
, near a bath tub, wash bowl, kitchen sink, or 
laundry tub; in a wet basement; or near a swimming pool; and the like.
 Stand — Do not place the product on an unstable cart, stand, tripod o\
r table. Placing the product on an unstable base  can cause the product to fall, resulting in serious personal injuries as\
 well as damage to the product. Use only a cart, 
stand, tripod, bracket or table recommended by the manufacturer or sold \
with the product. When mounting the product 
on a wall, be sure to follow the manufacturers instructions. Use only t\
he mounting hardware recommended by the 
manufacturer.
 Selecting the location — Select a place with no direct sunlight and g\
ood ventilation.
 Ventilation — The vents and other openings in the cabinet are designe\
d for ventilation. Do not cover or block these vents  and openings since insuf cient ventilation can cause overheating and/or shorten the life of the p\
roduct. Do not place 
the product on a bed, sofa, rug or other similar surface, since they can\
 block ventilation openings. This product is not 
designed for built-in installation; do not place the product in an enclo\
sed place such as a bookcase or rack, unless proper 
ventilation is provided or the manufacturers instructions are followed.\
 The Liquid Crystal panel used in this product is made of glass. Therefor\
e, it can break when the product is dropped or  applied with impact. Be careful not to be injured by broken glass pieces\
 in case the panel breaks.
 Heat — The product should be situated away from heat sources such as \
radiators, heat registers, stoves, or other  products (including ampli ers) that produce heat.
 The Liquid Crystal panel is a very high technology product with 1,049,08\
8 pixels, giving you  ne picture details.
  Occasionally, a few non-active pixels may appear on the screen as a \
 xed point of blue, green or red. Please note that  this does not affect the performance of your product.
 Lightning — For added protection for this television equipment during\
 a lightning storm, or when it is left unattended and  unused for long periods of time, unplug it from the wall outlet and disc\
onnect the antenna. This will prevent damage to 
the equipment due to lightning and power-line surges.
 Power Lines — An outside antenna system should not be located in the \
vicinity of overhead power lines or other electric  light or power circuits, or where it can fall into such power lines or c\
ircuits. When installing an outside antenna system, 
extreme care should be taken to keep from touching such power lines or c\
ircuits as contact with them might be fatal.
 To prevent  re, never place any type of candle or  ames on the top or near the TV set.
 To prevent  re or shock hazard, do not place the AC cord under the TV  set or other heavy items.
 Do not display a still picture for a long time, as this could cause an a\
fterimage to remain.
 To prevent  re or shock hazard, do not expose this product to dripping  or splashing.
  No objects  lled with liquids, such as vases, should be placed on the product.
Precautions when transporting the TV
 Be sure to always carry the TV by two people holding it with two hands —\
 one hand on each side of the TV.
 Turn off the main power and unplug the AC cord from the wall outlet befo\
re handling.
 Use a soft cloth and gently wipe the surface of the display panel. Using\
 a hard cloth may  scratch the panel surface.
 Use a soft damp cloth to gently wipe the panel when it is really dirty.
  (It may scratch the panel surface when wiped strongly.)
 If the panel is dusty, use an anti-static brush, which is commercially a\
vailable, to clean it.
 To protect the panel, do not use a dirty cloth, liquid cleaners or chemi\
cal cloth to clean it, such materials may damage  the panel surface.
 To clean the outer cabinet, use the same method. Do not use liquid or ae\
rosol cleaners.
- $  @ % 6 @& @ J O EE


-$@%6@&@JOEE


   


   



 
						

							6
1
2
Screws
Hex key
Soft cushion
Attaching/Detaching the Stand
 Before attaching (or detaching) the stand, unplug the AC  cord from the AC INPUT terminal.
 Before performing work spread cushioning over the base        area to lay the TV on. This will prevent it from being 
damaged.
CAUTIONAttach the stand in the correct direction.
 Do not remove the stand from the TV unless using an 
optional wall mount bracket to mount it.
 Be sure to follow the instructions. Incorrect installation 
of the stand may result in the TV falling over.
1  Con rm that there are 9 screws and a hex key 
supplied with the stand unit.
 
 
2   Attach the supporting post for the stand unit onto 
the base using the box for the stand unit as shown 
below.
Setting the TV on the Wall
CAUTION This TV should be mounted on the wall only with the 
AN-37AG5 (SHARP) wall mount bracket. The use of 
other wall mount brackets may result in an unstable 
installation and may cause serious injuries.
 Installing the TV requires special skill that should  only be performed by quali  ed service personnel. 
Customers should not attempt to do the work 
themselves. SHARP bears no responsibility for 
improper mounting or mounting that results in 
accident or injury.
Using an optional bracket to mount the TV
You can ask a quali ed service professional about 
using an optional AN-37AG5 bracket to mount the TV 
to the wall.
 Carefully read the instructions that come with the  bracket before beginning work.
QUICK REFERENCE
Vertical mounting Angular mounting
Hanging on the wall
AN-37AG5 wall mount bracket.
(See the bracket instructions for details.)
About setting the TV angle
0/5/10/15/20°LC-32D44U
The center of the display: 11/64 inch (4.0 mm) under 
the “A” position.
LC-37D44U
The center of the display: 1/4 inch (6.0 mm) above 
the “A” position.
Refer to the operation 
manual of AN-37AG5 for 
details.
3  1 Insert the stand into the openings on the bottom 
of the TV.
 
2 Insert and tighten the 4 screws into the 4 holes  on the rear of the TV.
 To detach the stand, perform the steps in reverse order.
 Detach the cable clamp on the rear of the TV when using 
the optional mount bracket.
 Due to the terminal con guration on this TV, when you  wall-mount this model, make sure there is enough space 
between the wall and the TV for the cables.
 To use this TV mounted on a wall,  rst remove the  adhesive tape at the 4 locations on the rear of the TV, and 
then use the screws supplied with the wall mount bracket 
to secure the bracket to the rear of the TV.
2
3
1
Hex key
Screws
- $  @ % 6 @& @ J O EE


-$@%6@&@JOEE


   


   



 
						

							7
Using the Remote Control UnitUse the remote control unit by pointing it towards the remote control se\
nsor on the TV. Objects between the 
remote control unit and the remote control sensor may prevent proper ope\
ration.
30º 30º30º
30º
17´ (5 m)
Remote Control sensor
■ 
Cautions regarding the remote control unit Do not expose the remote control unit to shock. In addition, 
do not expose the remote control unit to liquids, and do not 
place in an area with high humidity.
 Do not install or place the remote control unit under direct  sunlight. The heat may cause deformation of the remote 
control unit.
 The remote control unit may not work properly if the remote  control sensor on the TV is under direct sunlight or strong 
lighting. In such cases, change the angle of the lighting 
or the TV, or operate the remote control unit closer to the 
remote control sensor.
IMPORTANT:
The POWER indicator on the AQUOS television should light GREEN indicatin\
g you have power to the AQUOS television.
If the POWER indicator on the AQUOS television still does not light up, \
press  POWER on the remote control to turn the power 
on.
IMPORTANT:
IF THE UNIT DOES NOT POWER ON - UNPLUG THE AQUOS TELEVISION FROM THE OUT\
LET AND REPEAT THE 
INSTALLATION STEPS.
IF YOU STILL ENCOUNTER NO POWER, PLEASE CONTACT US AT 1-800-BE-SHARP.
QUICK REFERENCE
Attach your antenna to the back of the AQUOS 
television. (See page 8.) Bundle the cords properly with the cable clamp .
How to turn on the AQUOS television for the  rst time.A) Press 
POWER on the AQUOS television.
Connect the AC plug for the AQUOS television into 
the AC outlet.
B)  The POWER indicator on the front of the AQUOS television lights GREEN.
 Speakers cannot be detached from the TV.
 TV angle cannot be adjusted.
 Place the TV close to the AC outlet, and keep the power 
plug within reach.
  TO PREVENT RISK OF ELECTRIC SHOCK, DO NOT 
TOUCH UN-INSULATED PARTS OF ANY CABLES 
WITH THE AC CORD CONNECTED.
1
2 3
4
QUICK INSTALLATION TIPS
AC outlet
LC-32D44U LC-37D44U
POWER
POWER
 
indicator
- $  @ % 6 @& @ J O EE


-$@%6@&@JOEE


   


   



 
						

							8
Antennas
To enjoy a clearer picture, use an outdoor antenna. The following is a b\
rief explanation of the types of connections 
that are used for a coaxial cable. If your outdoor antenna uses a 75-ohm\
 coaxial cable with an F-type connector, 
plug it into the antenna terminal at the rear of the TV set.
1. A 75-ohm system is generally a round cable with F-type connector that can easily be attached to a terminal without tools (Commercially 
available).
F-type connector
300-ohm twin-lead cable ( at) F-type connector
75-ohm coaxial cable (round)
75-ohm coaxial cableNOTICE
2. A 300-ohm system is a  at “twin-lead” cable that can be attached  to a 75-ohm terminal through a 300/75-ohm adapter (Commercially 
available).
When connecting the RF cable to the TV set, do not tighten F-type 
connector with tools.
If tools are used, it may cause damage to your TV set. (The breaking 
of internal circuit, etc.)
300-ohm twin-lead cable
75-ohm coaxial cable (round)
75-ohm coaxial cable
IN OUT
300-ohm 
twin-lead cable
VHF
ANTENNA UHF
ANTENNA
Combiner 
(commercially available)
300/75-ohm adapter (commercially available)300-ohm twin-lead cable (flat)
75-ohm coaxial cable (round)
Cable TV lead-In
Coaxial cable
(commercially available) 
Coaxial cable
(commercially available)
 
Home Antenna
terminal (75-ohm) Home Antenna
terminal (75-ohm)
or
or
F-type connector should be  nger-tightened only.
CAUTIONImproper use of batteries can result in chemical leakage or explosion. B\
e sure to follow the instructions below.
 Do not mix batteries of different types. Different types of batteries ha\
ve different characteristics.
 Do not mix old and new batteries. Mixing old and new batteries can short\
en the life of new batteries or cause chemical leakag e 
in old batteries.
 Remove batteries as soon as they are worn out. Chemicals that leak from \
batteries that come in contact with skin can cause a  rash. If you  nd any chemical leakage, wipe thoroughly with a cloth.
 The batteries supplied with this product may have a shorter life expecta\
ncy due to storage conditions.
 If you will not be using the remote control unit for an extended period \
of time, remove batteries from it.
1  Open the battery cover.
 Place the batteries with their terminals 
corresponding to the ( e) and (
f) 
indications in the battery compartment.
2   Insert two “AA” size batteries 
(supplied with the product). 3
  Close the battery cover.
Installing Batteries in the Remote Control Unit
If the remote control fails to operate TV functions, replace the batteri\
es in the remote control unit.
Preparation
Connecting Antenna Cable
1   Cable without a CATV 
converter
3  Combination VHF/
UHF antenna
4  Separate VHF/UHF 
antenna
To TV antenna 
terminal
2
 VHF/UHF antenna

Connect the antenna cable to the TV using one of the methods in the illu\
stration as shown (
1, 
2 , 
3  or 
4).
-
$  @ % 6 @& J O EC 


-$@%6@&JOEC


   


   



 
						

							9
Part Names
TV (Front)
OPC indicator (See page 18.)
POWER  indicator (See page 12.)
OPC sensor (See page 18.)Remote control sensor
SLEEP indicator 
(See page 13.)
TV (Top/Rear)
POWER  button
INPUT 
buttonMENU 
button
Channel buttons
(
CH V/U )
Volume buttons
( VOL //. )
DIGITAL AUDIO OUTPUT terminal
INPUT 4 terminal (HDMI) INPUT 5 terminals (HDMI) INPUT 6 terminals (PC-IN)
Antenna/Cable in
INPUT 1 terminals
INPUT 2 terminals AUDIO OUTPUT terminals
SERVICE terminal
INPUT 3 terminals
AC INPUT terminal
-
$  @ % 6 @& J O EC 


-$@%6@&JOEC


   


   



 
						

							10
11
17
19
12
13
14
15
16
20
21
22
18
3 2
7
6
1
4
5
8
10
9
Part Names
Remote Control Unit1  POWER:  Switch the TV power on or enters 
standby. (See page 12.)
2   CC:  Display captions from a closed-caption 
source. (See page 15.)
3   AUDIO:  Selects the MTS/SAP or the audio mode 
during multi-channel audio broadcasts. (See page 
14.)
4   0–9:  Set the channel. (See page 13.)
5    (DOT):  (See page 13.)
6   FLASHBACK:  Return to the previous channel or 
external input mode. (See page 14.)
7   VIEW MODE:  Select the screen size. (See page 16.)
8   FREEZE:  Set the still image. Press again to return 
to normal screen. (See page 13.)
9  
a/
b /
c /
d ,
 ENTER:
 Select a desired item on the 
screen.
10  EXIT:  Turn off the menu screen.
11  DISPLAY:  Display the channel information.
12  SLEEP:  Set the sleep timer. (See page 13.)
13  AV MODE:  Select an audio or video setting. 
(When the input source is TV, INPUT 1, 2 or 3: 
STANDARD, MOVIE, GAME, USER, DYNAMIC 
(Fixed), DYNAMIC. When the input source is INPUT 
4, 5 or 6: STANDARD, MOVIE, GAME, PC, USER, 
DYNAMIC (Fixed), DYNAMIC) (See page 14.)
14  MUTE:  Mute the sound. (See page 13.)
15  VOL
k/
l :
 Set the volume. (See page 13.)
16  CH
r/
s :
 Select the channel. (See page 13.)
17  ENT:  Jumps to a channel after selecting with the 
0 –9  buttons.
18
  INPUT:  Select a TV input source. (TV, INPUT 1, 
INPUT 2, INPUT 3, INPUT 4, INPUT 5, INPUT 6) 
(See page 13.)
19  PC:  Quickly access to PC mode.
20  MENU:  Display the menu screen.
21  RETURN:  Return to the previous menu screen.
22  FAVORITE CH
  A, B , C , D:  Select 4 preset favorite channels in 4 
different categories. (See page 25.)
  While watching, you can toggle the selected  channels by pressing A, B, C and D.

-$  @ % 6 @& J O EC 


 -$@%6@&JOEC