Sharp DX B450P User Manual

User’s Guide3-5
Operator Panel Menus
Operator Panel
Operator Panel Menus
The tables below describe the items available in the Operator Panel. Each item is listed along 
with the values available for selection. If no values are available for selection, the Value and 
Default columns are blank. These menu items command the printer to execute an action that 
takes place immediately.
Job Library Menu
The Job Library menu handles the Job Retention feature’s stored jobs that have been sent to the 
printer from...

3-6User’s Guide
Operator Panel Menus
Operator Panel
Paper Menu
The Paper menu provides a variety of options for paper type selection as well as paper input and 
output. Items available in this menu are described below 
Menu ItemVa l u e  DefaultDescription
Copies 1-999 1 Sets number of copies printed.
Duplex On/Off Off Enables two-sided printing
Duplex Bind 2-sided Tablet
2-sided Book2-sided Book Choose the binding edge during duplex 
printing
Default Source Tray 1-4 Tray 1 Choose a default paper source...

User’s Guide3-7
Operator Panel Menus
Operator Panel
          Media Type Plain 
Transparency
Pre-Punched
Letter Head
Color
Pre-Printed
Bond
Labels
Card Stock
Postcard
Envelope
Thick 1 
Thick 2 
Thick 3 
(
DX-B450P only)
Thin 
(DX-B450P only)
Plain Set the paper type for a selected tray. See 
“Paper Types” on page 2-6 for more 
information.
         Custom Size Width
Length110 V: 
8.50 x 11.00 in
230V:
210 x 297 mmSet custom size for the selected tray. See 
“Custom Sizes” on page 2-6 for more...

3-8User’s Guide
Operator Panel Menus
Operator Panel
Interface Menu
The Interface menu provides a variety of options for port setup and network configuration. 
Items available in this menu are described below
Custom Size Unit Inches 
MillimetersInches for 110V
mm for 230VSet the unit of measurement for the Custom 
Paper Size feature.
Edge to Edge On/Off Off Enables a printing to the physical edge of the 
paper on all four sides.
Menu ItemVa l u e  DefaultDescription
PortEnable or disable operations from...

User’s Guide3-9
Operator Panel Menus
Operator Panel
     Delay Out Close On/Off Off When ON, the printer will wait until the job 
is completely printed and delivered to the 
output tray before terminating the 
connection, allowing all reverse-channel 
data to be sent back to the host. This will 
cause a reduction in printer throughput.
When OFF, reverse-channel data generated 
after the job interpretation is discarded. No 
reduction in printer throughput occurs.
     Binary PS On/Off On When On, the...

3-10User’s Guide
Operator Panel Menus
Operator Panel
     RTS On1/Off1 On/Off Off If On, the RTS signal will reflect the Online/
Offline status.
     RTS Error On/Off Off If On, the RTS signal will reflect the Error 
status.
     XON Ready/Busy On/Off On If On, the XON response will reflect the 
Ready/Busy status.
     XON On1/Off1 On/Off On If On, the XON response will reflect the 
Online/Offline status.
      XON Error On/Off Off If On, the XON response will reflect the 
Error status.
     DTR Polarity...

User’s Guide3-11
Operator Panel Menus
Operator Panel
     Network Address NA Displays MAC address of network interface.
     IP Address data entry 000.000.000.000 IP Address. If DHCP is enabled, this is 
read-only. Otherwise, this can be changed by 
the address can be set manually here
     Subnet Maskdata entry 000.000.000.000
     Default Gateway data entry 000.000.000.000
     LPD Banner On/Off Off If ON, prints a special “banner page” before 
each LPR print job.
     DHCP On/Off On
     IPv6 On/Off...

3-12User’s Guide
Operator Panel Menus
Operator Panel
     Binary PS On/Off On When On, the feature allows all binary codes 
to be processed by the PostScript interpreter. 
When Off, special binary control codes may 
be intercepted per the Format item setting.
     Factory Defaults Yes
NoNo Resets the menu to factory network defaults. 
     Connection Speed  Auto-Sense 
100Mbit Half
100Mbit Full
10Mbit Half
10Mbit FullAuto-Sense Configures the Ethernet connection speed 
(10 or 100 Mbits/second) and...

User’s Guide3-13
Operator Panel Menus
Operator Panel
PS Menu
The PS menu allows you to Print PS Errors. Items available in this menu are described below
PCL Menu
The PCL menu allows to set a variety of PCL settings. Items available in this menu are 
described below
     Format Raw
Normal
BinaryRaw Configures how incoming print jobs are 
scanned for special binary control codes.
RAW=no processing
Normal = “Adobe Standard Protocol” (ASP)
Binary = “Binary Control Protocol” (BCP)
When Interpreter setting is...

3-14User’s Guide
Operator Panel Menus
Operator Panel
Pitch 0.08 - 100.00 10.00 Change the default pitch of text.
Symbol Set All available 
symbol sets10U:PC-8 CP437 Choose a default symbol set.
Lines Per Page 5-128 60/Letter
64/A4Change the default number of lines per page. 
Default value varies by paper size selected.
CR Mode CR=CR
CR=CR/LFCR = CR Define the default action prompted by a 
carriage return—a carriage return equals 
either a carriage return alone, or a carriage 
return and a line feed...