Sharp AR M620N User Manual

PART 1: GENERAL INFORMATION
•BEFORE USING 
THE PRODUCT
•
MANAGING THE MACHINE
•PERIPHERAL DEVICES
PART 2: COPIER OPERATION
•MAKING COPIES
•CONVENIENT COPY 
FUNCTIONS
•
MACHINE MAINTENANCE 
(FOR COPYING)  
•DOCUMENT FILING 
FUNCTION
•
SPECIFICATIONS  1-1
2-1
3-1
4-1
5-1
6-1
7-1
8-1
Page
MODEL
OPERATION MANUAL
(for general information and copier operation)
(Option) Saddle stitch finisher + Punch module
+ Inserter + Large capacity tray
MODEL
AR-M550U
AR-M620U
AR-M550N
AR-M620N
DIGITAL LASER COPIER/PRINTER...

The CE mark logo label is affixed on an equipment in case that the directives described in the above
sentence are applicable to the product. (This sentence is not applicable in any country where the above
directives are not required.)
In some areas, the POWER switch positions are marked I and     on the copier 
instead of ON and OFF.
The symbol     denotes the copier is not completely de-energized but in a stand-by 
condition at this POWER switch position.
If your copier is so marked, please read I for...

Part 1: General Information
Downloaded From ManualsPrinter.com Manuals 

Downloaded From ManualsPrinter.com Manuals 

0-1
PRODUCT CONFIGURATIONS
The table below shows the product models covered by this manual. 
(As of December 2003)
OPERATION MANUALS
The following operation manuals are provided for the machine. Please read the appropriate manuals as needed for
the features you wish to learn about.

Operation manual (for general information and copier operation) (this manual):
The first half of this manual provides general information about the machine, including safety information, loading
paper, removing misfeeds, and...

0-2
Improper installation may damage this product. Please note the following during initial installation and whenever the
machine is moved.
1.The machine should be installed near an
accessible power outlet for easy connection.
2.Be sure to connect the power cord only to a
power outlet that meets the specified voltage and
current requirements. Also make certain the
outlet is properly grounded.

For the power supply requirements, see the
name plate on the back of the main unit.
3.Do not install your...

0-3
CAUTIONS
1. Do not touch the photoconductive drum. Scratches or smudges on the
drum will cause dirty prints.
2. The fusing unit is extremely hot.  Exercise care in this area. 
3. Do not look directly at the light source. Doing so may damage your
eyes.
4. Four adjusters are provided on all optional stand/paper drawer units.
These adjusters should be lowered until they contact the floor. 
When moving the machine with the optional stand/paper drawer, be
sure to raise the adjusters. Also, unlock the two...

CAUTIONS
0-4
Laser Information
Wave length
785 nm+10 nm
-15 nm
Pulse times North America: 55 cpm model: (3.1 µs ± 3.1 ns)/7 mm
62 cpm model: (3.1 µs ± 3.1 ns)/7 mm
Europe:  55 cpm model: (3.7 µs ± 3.7 ns)/7 mm
62 cpm model: (3.7 µs ± 3.7 ns)/7 mm
Output power Max 0.8 mW
At the production line, the output power of the scanner unit is adjusted to 0.8 MILLIWATT
PLUS 10 % and is maintained constant by the operation of the Automatic Power Control
(APC).
Caution
Use of controls or adjustments or performance of...

0-5
CONTENTS
Page
PRODUCT CONFIGURATIONS .................................. 0-1
OPERATION MANUALS.............................................. 0-1
INSTALLATION REQUIREMENTS.............................. 0-2
CAUTIONS................................................................... 0-3

Laser Information ................................................. 0-4
CONTENTS ................................................................. 0-5
CHAPTER 1
BEFORE USING THE PRODUCT...

CONTENTS
0-6
CHAPTER 5
CONVENIENT COPY FUNCTIONS
SPECIAL MODES ........................................................ 5-2

General procedure for using special functions ..... 5-2

Margin shift ........................................................... 5-3

Erase .................................................................... 5-4

Dual page copy..................................................... 5-5

Pamphlet copy ...................................................... 5-6

Job build...