Sharp Aquos Lc 70le735u Operation Manual

9
QUICK INSTALLATION TIPS
1Attach your antenna to the back of the television. 
(See page 10.)
2Connect the AC plug for the television into the AC 
outlet.
AC outlet
2
1
1
•  Place the TV close to the AC outlet, and keep the power plug within reach.
•  TO PREVENT RISK OF ELECTRIC SHOCK, DO NOT 
TOUCH UN-INSULATED PARTS OF ANY CABLES 
WITH THE AC CORD CONNECTED.
3When turning on the TV for the fi rst time, press 
POWER  on the television.
POWER
4Insert the batteries into the remote control unit. (See 
page...

10
Antennas
To enjoy a clearer picture, use an outdoor antenna. The following is a brief explanation of the types of connections 
that are used for a coaxial cable. If your outdoor antenna uses a 75-ohm coaxial cable with an F-type connector, 
plug it into the antenna terminal at the rear of the TV set. For connecting the antenna cable to the TV, use 
commercially available cables.
300-ohm twin-lead cable 75-ohm coaxial cable (round)
75-ohm coaxial cableINOUT
300-ohm
twin-lead cable VHFANTENNAUHF...

11
Part Names
TV (Front)
Center Icon illumination
(See page 33.)
Remote control sensor
*1 OPC: Optical Picture Control (See page 27.)
*2 This panel emits the infrared signal towards the 3D Glasses you wear when you view 3D images. 
Do not place anything between the 3D infrared emitter on the TV and the infrared receiver on the 3D Glasses.
3D infrared emitter *2
OPC sensor *1
TV (Rear/Side)
RS-232C terminal
Antenna/
Cable in POWER
button
MENU
button
INPUT
button
Channel
buttons
(CH
U/
V)
Volume
buttons...

12
118
19
20
21
4 3 2
5
23
24
8 7 6
9
25
26
28
29
15 14 13 12 11 10
16
17 27 22
1 POWER:
 Switch the TV power on or enter standby. (See 
page 18.)
2TV ,STB ,DVD•VCR ,AUDIO:  Switches the remote 
control for TV, STB, DVD, BD, VCR and AUDIO operation. 
(See pages 55 to 56 for details.)
  * To enter the code registration mode, you need to press  an appropriate button ( STB,DVD •VCR  or AUDIO ) and 
DISPLAY  at the same time.
3 External equipment operational buttons:  Operate the 
external equipment.
4...

13
Introduction to Connections
Types of Connection
For connecting the TV to external equipment, use commercially available \
cables.•   The illustrations of the terminals are for explanation purposes and may\
 vary slightly from the actual products.
■ Connecting to video equipment or PC
Image quality differs depending on the terminal used. To enjoy clearer i\
mages, check the output terminals of your 
external equipment and use its appropriate terminals for higher quality \
images.
Pages
14, 16, 17...

14
Connecting to External Equipment
You can connect many types of external equipment to your TV. To view ext\
ernal source images, select the input 
source from INPUT on the remote control unit or on the TV. (See pages 13 and 22.)
For connecting the TV to external equipment, use commercially available \
cables.
CAUTION
• To protect equipment, always turn off the TV before connecting any exter\
nal equipment.
• Please read the relevant operation manual (Blu-ray disc player, etc.) \
carefully before...

15
Connecting to External Equipment
■ When using Component cable (COMPONENT):
• Blu-ray disc player      • DVD player
• HD cable/satellite set-top box
COMPONENT OUT
AUDIO-L (White) AUDIO-R (Red)
Y (Green)
P
B (Blue)
P
R (Red) Audio cable
Component video cable
•  To enjoy 1080p display capability, connect your external equipment using\
 an HDMI-certifi ed cable or a component cable and  set the equipment to 1080p output.
•  See page 14 for connecting a Blu-ray disc player, DVD player or an HD ca\...

16
Connecting to External Equipment
Connecting a Surround System/Audio System
■ When connecting an AV amplifi
 er for surround system
DIGITAL AUDIO INPUTOPTICALHDMI IN
HDMI OUT
HDMI OUTHDMI-certified cable *1 HD Cable/Satellite set-top box
Optical fiber cable *2
•  Letting the TV output the audio to an AV amplifi er: *1 When you connect ARC-compatible equipment, use the HDMI 1 terminal.
*2 If the equipment to be connected is not compatible with the ARC, connect\
 an optical fi ber cable.
•  If the image is...

17
Connecting a PC
Refer to page 62 for a list of PC signals compatible with the TV.
■ When using HDMI cable (HDMI 1, 2, 3 or 4):
HDMI OUT
HDMI-certified cable
•  Depending on the board, only video signals may be output. In this case, in addition to connecting an HDMI-certifi ed cable 
to the HDMI 1 terminal, connect a Ø 3.5 mm stereo minijack cable to the AUDIO IN terminal and set "Audio Select" to 
"HDMI+Analog". (See page 62.)
•
The HDMI terminals only support digital signal.
■ When...

18
Turning On/Off the Power
POWER
POWER(On/Standby)
PressPOWER on the TV or on the remote control unit 
to turn the power on.
•  The Initial Installation starts when the TV powers on for the 
fi rst time. If the TV has been turned on before, the Initial 
Installation will not be invoked. For changing the settings of 
the Initial Installation, perform "EZ setup" on the Initial Setup 
menu on page 34.
PressPOWER on the TV or on the remote control unit 
again to turn the power off.
•  The TV enters...