Schwinn Journey 45 Manual

41
maInTenanCe
Read	all	maintenance	instructions	fully	before	you	start	any	repair	work.	In	some	conditions,	an	assistant	is	required	to	do	the	
necessary tasks.
Equipment	must	be	regularly	examined	for	damage	and	repairs.	The	owner	is	responsible	to	make	sure	that	regular	
maintenance	is	done.	Worn	or	damaged	components	must	be	repaired	or	replaced	immediately.	Only	manufacturer	
supplied components can be used to maintain and repair the equipment.
  To reduce the risk of electrical shock or...

42
Maintenance Parts
BBCC
ZDD
AA
Y
A
GC
B
D
E F H
J
O
P
Q
R
M
N
V
W
X
U
EE HH
L
GG
JJ
II
KK LL
T
S
O
FF FF
I
K
K
I  

43
AConsole NShroud, Right AAIncline	Motor	Assembly
B Heart	Rate	Cable,	Upper ORoller BBServo Motor
C Handlebar,	Static PLeg, Right CCBrake	Assembly
D Console	Cable,	Upper QShroud Cap DDFly Wheel
E Arm Pivot Rod RShroud,	Upper EEPedal Arm, Left
F Console Mast SConsole Cable, Lower FFTransport Wheel
G Water	Bottle	Holder TIncline	Assembly GGFront Stabilizer
H Handlebar	Arm,	Lower	Right URail Assembly HHLeg, Left
I Handlebar	Shroud,	Outer VFrame Assembly IIPower Cord
J Handlebar	Arm,	Upper	Right WShroud,...

44
Condition/ProblemThings to Check Solution
No	display/partial	display/
unit will not turn on Check	electrical	(wall)	
outlet Make sure unit is plugged into a functioning wall outlet.
Check connection at front 
of unit Connection should be secure and undamaged. Replace adapter 
or connection at unit if either are damaged.
Check data cable integrity All	wires	in	cable	should	be	intact.	If	any	are	visibly	crimped	or	
cut, replace cable.
Check data cable
connections/orientation Be	sure	cable	is	connected...

45
Condition/ProblemThings to Check Solution
No	speed/RPM	reading,	
Console displays “Please 
Stride” error code Check data cable integrity
All	wires	in	cable	should	be	intact.	If	any	are	cut	or	crimped,	
replace cable.
Check data cable
connections/orientation Be	sure	cable	is	connected	securely	and	oriented	properly.	Small	
latch on connector should line up and snap into place.
Check magnet position 
(requires	shroud	removal) Magnet should be in place on pulley. 
Check	Speed	Sensor	(re-
quires	shroud...

46
Condition/ProblemThings to Check Solution
Drive	train	click/tick	noise	
once per full crank revolu-
tion Check	crank/pulley	as-
sembly
Disconnect	left	and	right	foot	assemblies	and	rotate	crank.	If	
sound	persists,	replace	crank/pulley	assembly.	If	sound	does	
not	come	from	rotating	crank,	check	foot	assemblies	and	upper/
lower handlebars.
Check foot assemblies, leg 
assemblies, handlebar
assemblies Manually move foot, leg, and handlebar assemblies to isolate 
sound. Replace part making sound....

47
WarranTy
Who Is Covered
This warranty is valid only to the original purchaser and is not transfe\
rable or applicable to any other person(s).
What Is Covered
Nautilus, Inc. warrants that this product is free from defects in materi\
als and workmanship, when used for the purpose intended, under normal conditions, and provided it receives 
proper care and maintenance as described in the Product’s Assembly and Owner’s manual.  This warranty is good only for authentic, original, legitimat\
e machines...

8002141.121513.F
EN
Nautilus\25600250052005A00C00048005B\256Schwinn\25600030029004C0057005100480056005600380051004C00590048005500560044004F\256