Savage Arms Rimfire Bolt Action Mark I, Mark II, 93, Striker Instructions Manual

							Safe  ow n e rship is  your re s p o n s i b i l i t y.
Please thoroughly read and understand this
manual before loading your firearm.
Keep firearms and ammunition away fro m
c h i l d ren. Lock unloaded  firearms and
ammunition securely in separate locations.
Savage Arms recommends the use of good
quality high velocity factory manufactured
ammunition.I N S T R U C T I O N   M A N UA LBOLT ACTION RIMFIRE:
MARK I
MARK II
93
STRIKER
w w w. s a va g e a r m s. c o mIMPORTANT! DO NOT ATTEMPT TO LOAD AND SHOOT YOUR RIFLE UNTIL YOU HAVE THOROUGHLY
READ THIS INSTRUCTION MANUAL AND ARE FULLY FAMILIAR WITH ITS CONTENTS100 Springdale Road
Westfield, Massachusetts  
USA  01085
752429 (11/02) WARNING
Children are attracted to and can operate firearms that can cause severe injury
or death. Prevent child access by always keeping guns locked away and
unloaded when not in use. If you keep a loaded firearm where a child obtains
and improperly uses it, you may be fined or sent to prison.
ADVERTENCIA
Alos niños los atraen las armas de fuego y las pueden hacer funcionar. Ellos
pueden causarses lesiones graves y la muerte. Evite que los niños tengan
acceso a las armas de fuego guardándolas siempre con llave y descargadas
cuando no las esté utilizando. Si usted tiene un arma de fuego cargada en un
lugar en que un niño tiene acceso a ella y la usa indebidamente, le pueden dar
una multa o enviarlo a la carcel.
248 Water Street
P.O. Box 1240
Lakefield, Ontario
CANADA  K0L 2H0
w w w. s a va g e a r m s. c o m 
						

							1Congratulations on joining the Savage Arms
family of sporting firearms owners.  With
reasonable care, your firearm should deliver
years of reliable service and perform to our
“legend of accuracy”.
For your convenience, this INSTRUCTION
MANUALhas been divided into 8 sections:
SECTION 1:10 Commandments of Shooting Safety
SECTION 2:Basic Functions
SECTION 3:Rings And Bases For Mounting A
Scope
SECTION 4:Statement Of Limited Warranty
SECTION 5:MARK I Series (Parts List and
Diagram)
SECTION 6:MARK II Series (Parts List and
Diagram)
SECTION 7:Model 93 Series (Parts List and
Diagram)
SECTION 8:S T R I K E RSeries (Parts List and Diagram)
S E C T I O N   1  1 0   C O M M A N D M E N T S   O F   S H O O T I N GS A F E T Y
(The following excerpts are from SAAMI bulletin
#081 1MM 7/97 BP.  The entire booklet can be
obtained by calling: NATIONALSHOOTING
SPORTS FOUNDATION, 11 MILE HILLROAD,
NEWINGTON, CT  06470; 203-426-4358)Firearms Safety Depends On You
From the time you pick up a firearm, you become
part of a system over which you have complete
control.  You are the only part of the system that
can make a gun safe – or unsafe.
You can help meet this responsibility by enrolling
in hunter safety or shooter safety courses, if you
have not already done so.  You must constantly
stress safety when handling firearms, especially
to children and non-shooters.  Develop safe
shooting habits and remember firearms safety is
up to you.  Make no mistake about it.
ALCOHOL, DRUGS AND GUNS DON’T MIX
1.ALWAYS KEEPTHE MUZZLE POINTED IN ASAFE DIRECTION
This is the most basic safety rule.  If everyone
handled a firearm so carefully that the muzzle
never pointed at something they didn’t intend to
shoot, there would be virtually no firearm
accidents.  It’s as simple as that, and it’s up to you.
Never point your gun at anything you do not
intend to shoot.  Asafe direction means a
direction in which a bullet cannot possibly strike
anyone, taking into account possible ricochets
and the fact that bullets can penetrate walls and
ceilings.  Even when “dry firing” with an unloaded
gun, you should never point the gun at an
unintended target. This is your responsibility, and only you can
control it.
2.FIREARMS SHOULD BE UNLOADED WHENNOTACTUALLY IN USE
Firearms should be loaded only when you are 
in the field or on the target range or shooting
area, ready to shoot.  When not in use, firearms
and ammunition should be secured in a safe
place, separate from each other.  It is your
responsibility to prevent children and
inexperienced adults from gaining access to
firearms or ammunition.  Aloaded gun has no
place in or near a vehicle or building.
Whenever you handle a firearm or hand it to
someone, always open the action immediately,
and visually check the chamber, receiver and
magazine to be certain they do not contain any
ammunition.  Never assume a gun is unloaded –
check for yourself!  While in the field, there will be
times when common sense and the basic rules of
firearms safety will require you to unload your 
gun for maximum safety.  When in doubt, unload
your gun!
3.DON’T RELY ON YOUR GUN’S “SAFETY”
Treat every gun as though it can fire at any time,
regardless of pressure on the trigger.The
“safety” on any gun is a mechanical device,
which, like any such device, can become 
2 inoperable at the worst possible time.  The safety
serves as a supplement to proper gun handling
but cannot possibly serve as a substitute for
common sense.
Never touch the trigger on a firearm until you
actually intend to shoot.
Your firearm is a precision instrument.
Regardless of the position of the safety, any
bump strong enough to actuate the firing
mechanism of a gun can cause it to fire.  The
only time you can be absolutely certain that a gun
cannot fire is when the action is open and it is
completely empty. You and the safe gun handling
procedures you have learned are your gun’s
primary safeties.
4.BE SURE OF YOUR TARGETAND WHAT’SBEYOND IT
No one can call a bullet back.  Don’t shoot 
unless you know exactly what your bullet is going
to strike.  Be sure that your bullet will not injure
anyone or anything beyond your target.  You
should keep in mind how far a bullet will travel if it
misses your intended target or ricochets in
another direction.
Be aware that even a .22 short bullet can 
travel over 11
/
4miles and a high velocity 
cartridge, such as a 30-06, can project a bullet
more than 3 miles.  Shotgun pellets can travel
500 yards, and shotgun slugs have a range of
over a half-mile.5.USE CORRECTAMMUNITION
You must assume the serious responsibility of
using only the correct ammunition for your
firearm.  Read and heed all warnings, including
those that appear in the gun’s instruction manual
and on the ammunition boxes.  Using improper or
incorrect ammunition can destroy a gun and
cause serious personal injury.  It only takes one
cartridge of improper caliber or gauge to wreck
your gun, and only a second to check each one
as you load it.  Be absolutely certain that the
ammunition you are using matches the
specifications that are contained within the gun’s
instruction manual and the manufacturer’s
markings on the firearm barrel.
Hand loaded or reloaded ammunition deviating
from pressures generated by factory loads or
from competent recommendations specified in
reputable hand loading manuals can be
dangerous, and can cause severe damage to
guns and serious injury to the shooter.
Ammunition that has become very wet or has
been submerged in water should be discarded in
a safe manner.  Do not spray oil or solvents on
ammunition or place ammunition in excessively
lubricated firearms.
Form the habit of examining every cartridge you
put in your gun.  Never use damaged, old or
questionable ammunition – the money you save is
not worth the risk of possible injury or a ruined gun.WARNING
DISCHARGING  FIREARMS  IN  POORLY
VENTILATED AREAS, CLEANING FIREARMS
OR HANDLING AMMUNITION MAYRESULT IN
E XPOSURE  TO  LEAD  AND  OTHER
S U B S TANCE S  KNOWN  TO  CAUSE  BIRT H
DEFECTS,  REPRODUCTIVE  HARM A N D
OTHER SERIOUS PHYSICALINJURY.  HAVE
A D E Q U ATE  VENTILATION  AT A L LT I M E S .
WASH  HANDS  THOROUGHLYA F T E R
EXPOSURE.
6.IF YOUR GUN FAILS TO FIRE WHEN THETRIGGER IS PULLED, HANDLE WITH CARE!
Occasionally, a gun may not fire when the trigger
is pulled.  If this occurs, keep the muzzle pointed
in a safe direction.  Keep your face away from the
breech.  Then, carefully open the action, unload
the firearm and dispose of the cartridge in a safe
way.
Any time there is a cartridge in the chamber, your
gun is loaded and ready to fire – even if you’ve
tried to shoot and it did not go off.  It could go off
at any time, so you must always remember 
RULE #1and WATCH THAT MUZZLE! 
						

							3
7.ALWAYS WEAR EYE AND EARPROTECTION WHEN SHOOTING
All shooters should wear protective shooting
glasses and some form of hearing protectors
while shooting.  Exposure to shooting noise can
damage hearing, and adequate vision protection
is essential.  Wearing eye protection when
disassembling and cleaning any gun will also 
help prevent the possibility of springs, spring
tensioned parts, solvents or other agents from
contacting your eyes.  No target shooter, plinker
or hunter should ever be without them.
8.BE SURE THE BARREL IS CLEAR OFOBSTRUCTIONS BEFORE SHOOTING
Before you load your firearm, open the action 
and be certain that there is no cartridge in the
chamber.Then glance through the barrel to be
sure it is clear of any obstruction.  Even a small
piece of mud, snow, excess lubricating oil or
grease in the bore can cause dangerously
increased pressure, causing the barrel to bulge or
even burst when firing, which can cause injury to
the shooter and/or bystanders.  Make it a habit to
clean the bore with a cleaning rod and patch to
wipe away anti-rust compounds in the gun each
time immediately before you shoot it.  If the noise
or recoil on firing seems weak or doesn’t seem
quite “right”, cease firing immediately and be sure
to check that no obstruction or projectile has
become lodged in the barrel.9.DON’TALTER OR MODIFYYOUR GUN, AND HAVE GUNS SERVICED REGULARLY
Firearms are complicated mechanisms, which 
are designed by experts to function properly in
their original condition.  Any alteration or change
made to a firearm after manufacture can make
the gun dangerous and will usually void any
factory warranties.  Do not jeopardize your safety
or the safety of others by altering the trigger,
safety or other mechanism of any firearm or
allowing unqualified persons to repair or modify 
a gun.
Your gun is a mechanical device, which will 
not last forever and is subject to wear.As such, 
it requires periodic inspection, adjustment and
service.
10.LEARN THE MECHANISM AND HANDLINGCHARACTERISTICS OF THE FIREARMYOU ARE USING
Not all firearms are the same.  Consequently,
never handle any firearm without first having
thoroughly familiarized yourself with the particular
type of firearm you are using, the safe gun
handling rules for loading, unloading, carrying 
and handling that firearm, and the rules of safe
gun handling in general.  Locate the firearm’s
mechanical safety device and get familiar with the
feel and “on/off” positions.You should always read and refer to the
instruction manual you received with your gun, or
if you have misplaced the manual, simply contact
the manufacturer for a free copy.
Having a gun in your possession is a
full-time job.  You cannot guess; you
cannot forget.  You must know how to
use, handle and store your firearm
safely.  Do not use any firearm without
having a complete understanding of its
particular characteristics and safe use.
There is no such thing as a foolproof gun.
S E C T I O N   2    B A S I C   F U N C T I O N S
PRIOR  TO  LOADING  OR  OPERAT I N G ,
FAMILIARIZE Y O U R S E L FT H O R O U G H LY
WITH  THESE  OPERATING  INS TRUCTIONS 
AND THE MAIN PARTS OFYOUR FIREARM. 
FAILURE TO OBEYASAFETYWARNING MAY
RESULT IN INJURY TOYOU AND/OR OTHERS.
KNOW HOW TO LOCATE AND OPERATE THE
SAFETYMECHANISM.
SAVAGE ARMS, (CANADA) INC. DISCLAIMS
ANYRESPONSIBILITYFOR DAMAGE OR
INJURYWHICH RESULTS FROM ANY
MODIFICATIONS OR CHANGES THATARE
NOT A PART OF THE FIREARM AS
DELIVERED FROM THE FACTORY.SAFETY
The safety is located on the right side of the
receiver on right hand guns, and on the left side
of the receiver on left hand guns and the Striker
Series.
1.To put ON SAFE, pull rearward on the 
safety lever to fully expose the “S”.  See 
FIGURE 1.
(Right hand model shown)
2.To take OFFSAFE, push the safety lever
forward to cover the “S” and fully expose the
red dot.  See FIGURE 2.(Right hand model shown)CAUTION
WHEN CARRYING ALOADED FIREARM, THE
SAFETYMUST ALWAYS BE IN THE ON SAFE
POSITION.
THE ONLYTIME YOU CAN BE ABSOLUTELY
C E RTAIN  THAT  A GUN  CANNOT  FIRE  IS  
WHEN  THE  ACTION  IS  OPEN  AND  IT  IS
COMPLETELYEMPTYOFAMMUNITION.LOADING
FIREARMS SHOULD BE LOADED ONLYWHEN
YOU ARE IN THE FIELD, ON THE TARGET
RANGE, OR AT ASHOOTING AREAREADYTO
SHOOT.
ALWAYS KEEPTHE MUZZLE POINTED IN A
SAFE DIRECTION.USE  ONLY THE  CORRECT  AMM UNITION 
T H AT  IS  STAMPED  ON  THE  SIDE  OFT H E
BARREL.
LOOK THROUGH AND THOROUGHLYCLEAN
THE INSIDE OFTHE BARRELAND CHAMBER
TO  ASSURE  THERE  ARE  NO  P OSSIBLE
OBSTRUCTIONS PRIOR TO LOADING.
SAVAGE ARMS, (CANADA) INC. DISCLAIMS
ANYRESPONSIBILITYFOR DAMAGE OR
INJURYWHICH RESULTS FROM THE USE OF
OTHER THAN FACTORYMANUFACTURED
AMMUNITION.LOADING – REMOVABLE MAGAZINE (CLIP)
1.With the muzzle of the firearm pointed in a
safe direction, move the safety fully rearward
to the ON SAFEposition.
2.Placing one hand over the ejection port, slowly
lift the bolt handle up and pull fully rearward to
extract the live cartridge from the chamber (if
there is one).
3.With one hand prepared to catch the
removable magazine, pull the latch at the rear
of the magazine, ejecting the magazine into
your hand.  See FIGURE 3.
4FIGURE 1FIGURE 2ON SAFEOFF SAFE 
						

							(MARK II shown)
4.Look and feel to be sure there are no
cartridges in the chamber.
5.As shown in FIGURE 4, load the correct
caliber cartridges into the removable magazine 
by pressing downward and to the rear.
(.22LR 10 shot magazine shown)6.Insert the removable magazine back into 
the stock opening, pressing upward until the
latch snaps into position and is fully engaged.
7.Moving the bolt handle forward and down 
will push the first cartridge from the magazine 
into the chamber.
•When the bolt is fully closed, a live cartridge
will be IN THE CHAMBER.
ALWAYS KEEPTHE MUZZLE POINTED IN A
SAFE DIRECTION.LOADING –  SINGLE SHOT
1.Move the safety fully rearward to the ON SAFE
position,locking the trigger mechanism.
2.Lift the bolt handle up and fully rearward.
3.Insert a cartridge into the chamber as shown in
FIGURE 5. (MARK I shown)
4.Move the bolt handle forward and down.
•When the bolt is fully closed, a live cartridge
will be IN THE CHAMBER.
ALWAYS KEEPTHE MUZZLE POINTED IN A
SAFE DIRECTION.TO FIRE
DO NOT MOVE THE SAFETYFORWARD TO
THE OFF SAFE[READYTO FIRE]POSITION
UNTILYOU ARE READYTO SHOOT.
1.Keep your finger off the trigger and out of the
trigger guard until you are ready to shoot.
THE ONLYTIME YOU CAN BE ABSOLUTELY
C E RTAIN  THAT  A GUN  CANNOT  FIRE  IS  
WHEN  THE  ACTION  IS  OPE N  AND  IT  IS
COMPLETELYEMPTYOFAMMUNITION. 5FIGURE 3FIGURE 4FIGURE 56 2.Always look carefully around to be sure that no
one will cross in front of you when you are
ready to shoot.
3.Place the firearm in shooting position and
move the safety forward to the OFFSAFE
[READYTO FIRE] position and take aim.
NEVER TOUCH THE TRIGGER ON AFIREARM
UNTILYOU ACTUALLYINTEND TO SHOOT.
NEVER POINT YOUR GUN ATANYTHING YOU
DO NOT INTEND TO SHOOT.
4.Place your finger into the trigger guard and when
you are on target, squeeze the trigger slowly.
NO ONE CAN CALLABULLET BACK !!! CAUTION
SHOULD YOU NOTICE WHATAPPEARS TO
BE  GAS  PRES SURE/RE SIDUALP O W D E R
COMING FROM THE BOLTAREA, THIS MAY
BE  WHAT  IS  KNOWN  AS  “BLOW  BACK”.
A LTHOUGH  WEARING  SAFETYG L A S S E S
W I L LPROTECT  Y OUR  EYE S,  WE
RECOMMEND TRYING ADIFFERENT BRAND
O FAMMUNITION  IN  ORDER  TO  CORRECT 
THE  SITUATION.  S HOULD  YOU  STILLB E
EXPERIENCING THIS CONDITION, OR OTHER
OPERATING DIFFICULTY, PLEASE CONTACT
OUR SERVICE DEPARTMENT AT 413-568-7001.5.Pull up and fully rearward on the bolt handle to
open the bolt to extract the fired case.
ALWAYS KEEPTHE MUZZLE POINTED IN A
SAFE DIRECTION.
6.Moving the bolt handle forward and down will
push the next cartridge from the magazine into
the chamber.
7.Move the safety fully rearward to the ON SAFE
position when not firing.UNLOADING – REMOVABLE MAGAZINE (CLIP)
1.With the muzzle pointed in a safe direction,
move the safety fully rearward to the ON SAFE
position.
K E E PYOUR  FINGERS  AWAY FROM  THE
TRIGGER.
2.Placing one hand over the ejection port, slowly
lift the bolt handle up and pull fully rearward to
extract the live cartridge from the chamber (if
there is one).
3.With one hand prepared to catch the
removable magazine, pull the latch at the rear
of the magazine, ejecting the magazine into
your hand.ALOADED GUN HAS NO PLACE IN OR NEAR
AVEHICLE OR BUILDING.CAUTION
LOOK AND FEEL!  BE SURE THE CHAMBER
AND MAGAZINE ARE COMPLETELYEMPTY–
DO NOT ASSUME!UNLOADING – SINGLE SHOT
1.With the muzzle pointed in a safe direction,
move the safety fully rearward to the ON SAFE
position.
KEEPYOUR FINGERS AWAYFROM THE
TRIGGER.
2.Placing one hand over the ejection port, slowly
lift the bolt handle up and pull fully rearward to
extract the live cartridge from the chamber.
3.Remove the cartridge with your fingers.
ALOADED GUN HAS NO PLACE IN OR NEAR
AVEHICLE OR BUILDING.CAUTION
LOOK AND FEEL!  BE SURE THE CHAMBER 
IS EMPTY— DO NOT ASSUME! 
						

							CLEANING AND CARE OF YOUR FIREARM
YOUR GUN IS AMECHANICALDEVICE THAT
WILLNOT LAST FOREVER AND IS SUBJECT
TO WEAR.TO REMOVE THE BOLT
ALWAYS KEEPTHE MUZZLE POINTED IN A
SAFE DIRECTION.
ALOADED GUN HAS NO PLACE IN OR NEAR A
VEHICLE OR BUILDING.
1.Placing one hand over the ejection port, slowly
lift the bolt handle up and pull fully rearward to
extract the live cartridge from the chamber (if
there is one).
2.With one hand prepared to catch the
removable magazine, pull the latch at the rear
of the magazine, ejecting the magazine into
your hand.
3.Look and feel to be sure there are no
cartridges in the chamber.
4.Move the safety forward to the OFFSAFE
[READYTO FIRE] position.
5.Pull back on the trigger and slide the bolt out of
the rear of the receiver.  See FIGURE 6.(MARK I shown)
6.Care should be taken not to hit the stock with
the bolt.
DO NOT DISASSEMBLE THE BOLTASSEMBLY.CAUTION
B O LT  ASSEMBLIES  ARE  SPECIFICALLY
M ATCHED  TO  A FIREARM.    USING A N Y
OTHER  BOLT A S S E M B LYM AYC A U S E
EXTENSIVE  DAMAGE   TO  THE  FIREARM
AND/OR SERIOUS INJURY TO THE SHOOTER
OR BYSTANDER.
DISASSEMBLE   ONLY ONE  FIRE ARM  AT 
A TIME  TO  AVOID  INTERCHANGING
COMPONENTS.CLEANING THE BORE
LOOK AND FEEL!  BE SURE THE CHAMBER
AND MAGAZINE ARE COMPLETELYEMPTY—
DO NOT ASSUME!!!
NEVER ATTEMPT TO DISASSEMBLE, CLEAN,
OR OILALOADED FIREARM!
BE SURE TO READ AND UNDERSTAND ALL
OFTHE CAUTIONS AND WARNINGS ON ALL
SOLVENTS AND CHEMICALS PRIOR TO USE.
FOLLOW   THE  MANUFA C T U R E R ’ S
INSTRUCTIONS   FOR  BEST  CL EANING
RESULTS.
1.Prepare an area for cleaning the firearm with a
suitable surface, adequate ventilation, and the
correct caliber cleaning rod, brush, patches,
powder solvent, and oil.
2.Follow the instructions under “TO REMOVE
THE BOLT” (see page 7) before cleaning.
3.Lay the firearm horizontally with the ejection
port facing down.
A LWAYS  STA RTING  FROM  THE  CHAMBER
END, PUSH THE CLEANING ROD THROUGH
THE BORE AND OUT THE MUZZLE END.
4.Using a small amount of powder solvent on the
brush, push the cleaning rod through the barrel
several times. 7FIGURE 685.Unscrew the brush from the cleaning rod and
replace it with a patch tip.
6.Push a new patch through the bore starting
from the chamber end and out the muzzle.
7.Repeat step 6 several times.
8.Push a new patch lightly saturated with gun oil
through the bore.
9.Push a new dry patch through the bore to
remove the excess oil.
AVERYTHIN FILM OFOILIS SUFFICIENT
PROTECTION – DO NOT OVER OIL!!!
YOUR GUN IS AMECHANICALDEVICE THAT
WILLNOT LAST FOREVER AND IS SUBJECT
TO  WEAR.    CONTACT S AVAGE A R M S
S E RVICE  DEPA RTM ENT  FOR  PERIODIC
INSPECTION, ADJUSTMENT AND SERVICE.PROTECTING METAL SURFACES
1.In order to be able to reach all surfaces,
remove the bolt prior to cleaning and oiling.
2.With a soft cloth, remove any foreign matter
(i.e. mud, twigs, grass).3.Apply a thin coat of gun oil on all cleaned
metal surfaces.  Rubbing may be necessary to
remove any signs of rust.
4.Where accessible, clean and lightly oil interior
metal surfaces.TO REPLACE BOLT
1.Make sure that the magazine is removed, the
safety is in the OFFSAFE [READYTO FIRE]
position, and the bolt is in the cocked position
(the guide pin aligned with the bolt arm, see
FIGURE7).
2.Hold the bolt so the firing pin is located top
center.  With the trigger pulled, slide the bolt 
into the rear of the receiver.
•If you encounter difficulty, remove the bolt
and re-check the alignment.  Never force
the bolt into the receiver.S E C T I O N   3    R I N G S   &   B A S E S   F O R   M O U N T I N G  AS C O P E
The following Companies manufacturer RINGS
and BASESthat fit Savage firearms.
The manufacturers listed below should be
contacted for specific part numbers and
information.WEAVER 
P.O. Box 39
Onalaska, WI  54650
800-635-7656www.weaveroptics.comBURRIS
331 East 8th
Street
Greeley, CO  80631
970-356-1670www.burrisoptics.com
KWIK-SITE
5555 Treadwell
Wayne, MI  48184
[email protected]
7275 Murdy Circle
Huntington Beach, CA
92647
800-645-5388www.millettsights.com
B-SQUARE
P.O. Box 11281
Fort Worth, TX  76110
800-433-2909www.b-square.comLEUPOLD
14400 NW Greenbrier
Parkway
Beaverton, OR  97006
503-526-5196www.leupold.comFIGURE 7 guide pinbolt arm 
						

							S E C T I O N   4    S TAT E M E N T   O F   L I M I T E D  WA R R A N T Y
Please complete the WARRANTY
REGISTRATION CARDand return it to Savage
Arms, Inc.within ten (10) days from the date of
purchase.
Savage Arms, Inc. must be notified within one
(1) year from the date of purchase of any defect
in materials or workmanship encountered during
normal use.
WHO IS COVERED?  
The original owner (with proof of purchase).
WHATIS COVERED?
Any defect in materials or workmanship
performed at Savage Arms.
HOW LONG IS THE WARRANTYPERIOD?
One (1) year from the date of purchase.
WHATIS NOTCOVERED?
PERSONALINJURY, PROPERTYDAMAGE,
AND/OR DAMAGE TO THE FIREARM CAUSED
BY:
•Negligence to provide proper care and
maintenance.•Alterations/modifications performed without
the expressed authorization of Savage
Arms, Inc.Service Department.
•Normal wear; tear; and/or corrosion.
•Accidental discharge, careless handling,
and/or misuse.
•Barrel obstructions.EXCLUSIONS AND LIMITATIONS:
This WARRANTYand the remedies set forth
herein are exclusive and take the place of all
other expressed or implied WARRANTIES
(including any implied WARRANTYof
merchantability or fitness for any particular
purpose which are disclaimed).  No other
representations or claims of any nature shall be
binding on or obligate Savage Arms, Inc.
Savage Arms, Inc.excludes any incidental and
consequential damages under this warranty.
Some states do not allow exclusions or limitations
on how long an implied warranty lasts, so the
above limitations may not apply to you.
This WARRANTYgives you specific legal rights.
You may have other rights, which will vary, from
state to state.RETURNING A FIREARM:
For WARRANTYclaims, proof of purchase must
accompany the firearm.
It is a violation of Federal Law to ship a firearm
with live ammunition either in the box or in the
firearm itself.  If received, The Bureau of Alcohol,
Tobacco, and Firearms must be notified!
Savage Arms, Inc.is not responsible for the loss
or damage to any accessories shipped with the
firearm.
If there is a question whether the firearm should
be returned or parts could be purchased, please
call 1-413-568-7001 between 9:00 am and 
3:30 p.m. ESTand ask for the Service/Warranty
Department.
All firearms are to be sent to Savage Arms, Inc.
at the owner’s expense.  Warranty repairs will be
returned to the owner at the expense of Savage
Arms, Inc.
1.Pack the firearm in its original box if possible
(or a similar suitable box), being careful to
include any support pieces.
2.Enclose a brief note including:
•Name, address and phone number of
sender. 910 •Best time and method to contact sender.
•Serial number of firearm.
•Description of the problem you are having.
•Bullet weight, bullet type, sabot, powder
type and charge you are using.
•Any other information that you feel may be
helpful.
3.Return to:
Savage Arms, Inc.
100 Springdale Road
Westfield, MA01085
Attn:  Service Department
Phone:  413-568-7001
Fax:  413-568-8386
4.If there will be a charge involved for the repair,
a quote will be sent within fourteen (14)
working days.
•If there is no response from the quote 
within (30) days, the firearm will be returned
COD ($20.00 Shipping/Handling).
•Firearms will be repaired typically 4 weeks
after receipt of payment in the order they
were received. 
						

							12M A R K   I
Not To ScaleS E C T I O N   5    
M A R K   I   S e r i e s  
PARTS MAYBE ORDERED DIRECTLYFROM
SAVAGE ARMS[PHONE 413-568-7001]
BETWEEN THE HOURS OF9:00 AND 3:30
(EASTERN STANDARD TIME).  THERE IS A
MINIMUM ORDER AND PLEASE ALLOW 2
WEEKS FOR DELIVERY.
PLEASE BE ADVISED THAT SOME PARTS 
MAYREQUIRE FITTING.  SAVAGE ARMS
BEARS NO RESPONSIBILITYFOR THE
FUNCTION OR PERFORMANCE OFANY
FIREARM THAT HAS BEEN REPAIRED OR
MODIFIED BYOTHER THAN SAVAGE ARMS
SERVICE DEPARTMENT.AS SUCH, SAVAGE
ARMSACCEPTS NO RESPONSIBILITY/
LIABILITYFOR ANYDIRECT AND/OR
CONSEQUENTIALDAMAGE AND/OR INJURY
RESULTING FROM THE USE OFAFIREARM
REPAIRED OR MODIFIED BYOTHER THAN
THE SAVAGE ARMSSERVICE DEPARTMENT.
*RESTRICTED TO FACTORYINSTALLATION ONLY#DescriptionPart # 
1Front sight700427
2Rear sight700414
3Universal elevator104860
4Feed ramp RH701204
Feed ramp LH701206
*5Bolt assembly RH702260
Bolt assembly LH702291
6Firing pin702482
7Extractor RH702254
Extractor LH702296
8Cartridge guide RH702256
Cartridge guide LH702297
9Extractor spring clip702255
10Front stud702229
10AStock assembly stud702279
11Receiver pin702478
12Bolt guide RH702231
Bolt guide LH702292
13Spacer washer (2 req’d)701203
14Trigger/mag housing screw  702230
15Lock washer (2 req’d)702270
16Trigger assembly RH 702293
Trigger assembly LH702294
17Rear stud702234
18Stock wood RH701265
Stock wood RH uncheckered701255
Stock wood RH youth701269
Stock wood RH youth camo701281
Stock wood RH youth camo701263
uncheckered
Stock wood RH youth uncheckered701259
Stock wood LH701266
Stock wood LH uncheckered701256
Stock color laminate RH702304
Stock color laminate RH uncheckered70126419Trigger guard700489
20Trigger guard/mag plate screw700488
(2 req’d)
21Stock assembly screw (2 req’d)700475
*22Barrel/receiver assembly RH
Barrel/receiver assembly RH youth
Barrel/receiver assembly RH smooth bore 
Barrel/receiver assembly LH 11 
						

							S E C T I O N   6    
M A R K   I I   S e r i e s  
PARTS MAYBE ORDERED DIRECTLYFROM
SAVAGE ARMS[PHONE 413-568-7001]
BETWEEN THE HOURS OF9:00 AND 3:30
(EASTERN STANDARD TIME).  THERE IS A
MINIMUM ORDER AND PLEASE ALLOW 2
WEEKS FOR DELIVERY.
PLEASE BE ADVISED THAT SOME PARTS 
MAYREQUIRE FITTING.  SAVAGE ARMS
BEARS NO RESPONSIBILITYFOR THE
FUNCTION OR PERFORMANCE OFANY
FIREARM THAT HAS BEEN REPAIRED OR
MODIFIED BYOTHER THAN SAVAGE ARMS
SERVICE DEPARTMENT.AS SUCH, SAVAGE
ARMSACCEPTS NO RESPONSIBILITY/
LIABILITYFOR ANYDIRECT AND/OR
CONSEQUENTIALDAMAGE AND/OR INJURY
RESULTING FROM THE USE OFAFIREARM
REPAIRED OR MODIFIED BYOTHER THAN
THE SAVAGE ARMSSERVICE DEPARTMENT.
*RESTRICTED TO FACTORYINSTALLATION ONLY#Description Part #
1Front sight700427
2Rear sight700414
3Universal elevator104860
*5Bolt assembly RH702260
Bolt assembly RH SS702360
Bolt assembly LH702291
6Firing pin702482
7Extractor RH702254
Extractor LH702296
8Cartridge guide RH702256
Cartridge guide LH702297
9Extractor spring clip702255
10Front stud702229
10AStock assembly stud702279
11Receiver pin702478
12Bolt guide RH702231
Bolt guide LH702292
13Spacer washer 701203
14Trigger/mag housing screw 702230
(2 req’d)    
15Lock washer (2 req’d)702270
16Trigger assembly RH702293
Trigger assembly RH702433
(synthetic stock)
Trigger assembly RH SS702413
(synthetic stock)
Trigger assembly LH702294
17Rear stud702234
19Trigger guard700489
20Trigger guard/mag plate screw700488
(3 req’d) 
21Stock assembly screw (2 req’d)700475*45Barrel/receiver assembly RH
Barrel/receiver assembly RH youth
Barrel/receiver assembly RH heavy barrel
Barrel/receiver assembly RHSS
Barrel/receiver assembly LH
Barrel/receiver assembly LH youth 
46Stock wood RH702267
Stock wood RH youth702271
Stock wood RH laminate 702286
heavy barrel
Stock wood LH702268
Stock wood LH youth 702272
Stock synthetic RH702282
Stock synthetic RH heavy barrel702415
Stock synthetic RH camo702427
47Magazine assembly 5 shot702219
Magazine assembly 10 shot702227
Magazine assembly SS 5 shot702321
Magazine assembly SS 10 shot702327
48Magazine housing702226
Magazine housing SS702326
49Magazine retaining spring702228
Magazine retaining spring SS702328
50Magazine plate702477
150Scope base/screws (2 req’d)702285 1314M A R K   I I
Not To Scale 
						

							S E C T I O N   7
M o d e l   9 3   S e r i e s  
PARTS MAYBE ORDERED DIRECTLYFROM
SAVAGE ARMS[PHONE 413-568-7001]
BETWEEN THE HOURS OF9:00 AND 3:30
(EASTERN STANDARD TIME).  THERE IS A
MINIMUM ORDER AND PLEASE ALLOW 2
WEEKS FOR DELIVERY.
PLEASE BE ADVISED THAT SOME PARTS 
MAYREQUIRE FITTING.  SAVAGE ARMS
BEARS NO RESPONSIBILITYFOR THE
FUNCTION OR PERFORMANCE OFANY
FIREARM THAT HAS BEEN REPAIRED OR
MODIFIED BYOTHER THAN SAVAGE ARMS
SERVICE DEPARTMENT.AS SUCH, SAVAGE
ARMSACCEPTS NO RESPONSIBILITY/
LIABILITYFOR ANYDIRECT AND/OR
CONSEQUENTIALDAMAGE AND/OR INJURY
RESULTING FROM THE USE OFAFIREARM
REPAIRED OR MODIFIED BYOTHER THAN
THE SAVAGE ARMSSERVICE DEPARTMENT.
*RESTRICTED TO FACTORYINSTALLATION ONLY#DescriptionPart #
1Front sight700427
2Rear sight700414
3Universal elevator104860
7Extractor RH702254
Extractor LH702296
8Cartridge guide RH702256 
Cartridge guide LH702297
9Extractor spring clip702255
10Front stud702229
10AStock assembly stud702279
11Receiver pin702210
16Trigger assembly RH702293
Trigger assembly RH SS702413
Trigger assembly RH702433
(synthetic stock) 
Trigger assembly RH SS702413
(synthetic stock)
Trigger assembly LH702294
17Rear stud702234
19Trigger guard700489
20Trigger guard/mag plate screw700488
(3 req’d)
21Stock assembly screw (2 req’d)700475
46Stock wood RH702267
Stock wood RH heavy barrel702306
Stock wood LH702268
Stock wood LH heavy barrel702274
Stock synthetic RH703282
Stock synthetic RH camo703219
Stock synthetic RH heavy barrel703320
Stock color laminate RH heavy barrel70228651Bolt guide RH703231
Bolt guide LH703232
52L’bar703226
L’bar SS703326
53Magazine retaining spring703228
Magazine retaining spring SS 703328
54L’bar screw (2 req’d)703230
54ALock washer (2 req’d)702270
55Magazine assembly703227
Magazine assembly SS703327
*56Barrel/receiver assembly RH
Barrel/receiver assembly RH heavy barrel SS
Barrel/receiver assembly RH SS
Barrel/receiver assembly LH
Barrel/receiver assembly .17HMR RH
Barrel/receiver assembly .17HMR RH SS
Barrel/receiver assembly .17HMR RH heavy barrel
Barrel/receiver assembly .17HMR RH heavy barrelS S
Barrel/receiver assembly .17HMR LH heavy barrel
*57Bolt assembly RH703281
Bolt assembly RH SS703360
Bolt assembly LH703293
58Recoil lug703212
58ARecoil lug screw703276
59Magazine plate703278
60Firing pin703482
150Scope base/screws (2 req’d)702285
Scope base/screws SS (2 req’d)703317 1516M o d e l   9 3
Not To Scale 
						

							S E C T I O N   8
S T R I K E RS e r i e s
PARTS MAYBE ORDERED DIRECTLYFROM
SAVAGE ARMS[PHONE 413-568-7001]
BETWEEN THE HOURS OF9:00 AND 3:30
(EASTERN STANDARD TIME).  THERE IS A
MINIMUM ORDER AND PLEASE ALLOW 2
WEEKS FOR DELIVERY.
PLEASE BE ADVISED THAT SOME PARTS 
MAYREQUIRE FITTING.  SAVAGE ARMS
BEARS NO RESPONSIBILITYFOR THE
FUNCTION OR PERFORMANCE OFANY
FIREARM THAT HAS BEEN REPAIRED OR
MODIFIED BYOTHER THAN SAVAGE ARMS
SERVICE DEPARTMENT.AS SUCH, SAVAGE
ARMSACCEPTS NO RESPONSIBILITY/
LIABILITYFOR ANYDIRECT AND/OR
CONSEQUENTIALDAMAGE AND/OR INJURY
RESULTING FROM THE USE OFAFIREARM
REPAIRED OR MODIFIED BYOTHER THAN
THE SAVAGE ARMSSERVICE DEPARTMENT.
*RESTRICTED TO FACTORYINSTALLATION ONLY#DescriptionPart #
BOTH MODELS 501, 502 & 503
1Stock assembly screw (2 req’d)700475
2Rear stud702234
3Extractor RH702254
4Cartridge guide RH702256
5Lock washer702270
6Scope base/screws (2 req’d)702285
Scope base/screws SS (2 req’d)703317
7Stock assembly stud702279
8 Trigger assembly LH702412
Trigger assembly LH SS703118
9Stock synthetic .22LR702265
Stock synthetic .22WMR/.17HMR703265
10Extractor spring clip702255
*29Barrel/receiver assembly .22LR702430
Barrel/receiver assembly .22WMR703286
Barrel/receiver assembly .17HMR703200
Barrel/receiver assembly .17HMR SS703112
32Front stud702229
MODEL501 .22LR  
22Magazine housing702226
23Magazine assembly702227
24Magazine retaining spring702228
25Trigger/mag housing screw702230 
26Bolt guide RH702231
27Firing pin702482
28Spacer washer701203
*30Bolt assembly .22LR702425MODEL502 .22WMR & 503 .17HMR
12Recoil lug703212
12ARecoil lug screw703276
13L’bar703226
L’bar SS703326
14Magazine assembly703227
Magazine assembly SS703327
15Magazine retaining spring703228
Magazine retaining spring SS703328
16L’bar screw703230
17Bolt guide RH703231
18Firing pin703482
*19Bolt assembly .22WMR/.17HMR703257
Bolt assembly .17HMR SS703260 1718S T R I K E R
Not To Scale