Sanyo VPC S4 User Manual

English98
CHECKING THE REMAINING CARD MEMORY AND INTERNAL MEMORY
You can check how many images can be captured and how much recording 
time is available on the card or in the cameras internal memory. For a table 
showing the maximum number of images and recording time for specific 
cards, please see “Possible No. of Images/Possible Shooting Time” on 
page 133. 
Checking the remaining number of images and video recording time 
1 Set the camera to the desired 
shooting mode (see pages 29 and 
30). 
hThe...

99English
CHECKING THE REMAINING BATTERY CHARGE
When using the batteries, the remaining battery charge can be checked on 
the LCD monitor. Make sure to check this indicator before capturing an 
image. Please see page 132 for information regarding the battery life.
1 Display a Shooting or Playback 
Setting Screen (see pages 40 and 
62). 
hThe battery remaining charge 
indicator appears in the lower right 
corner of the LCD monitor. 
hDue to the battery characteristics, 
when the ambient temperature is...

English100
HINT 
iBattery life may differ even among batteries of the same type. 
iDepending on the usage of the digital camera (such as the number of 
times the flash is used, the use of the LCD monitor, etc.) or the 
environmental conditions (temperature, etc.) the number of images that 
can be saved on fully charged batteries will vary greatly. 
NOTE
iIt is recommended that you prepare extra batteries when taking pictures at 
a wedding or while traveling, for example, so you don’t miss capturing...

101English
OTHER FUNCTIONS AND CONNECTIONS
CONNECTING TO A COMPUTER
How to connect your camera to a computer
1 Turn off your digital camera (see page 24).
2 Using the supplied dedicated USB interface cable, connect the 
camera connector to the camera and the computer connector to the 
proper terminal on your computer.
iPlease connect the dedicated USB interface cable to your computers USB 
connector. Do not connect it to the USB port on your monitor or keyboard, 
or to the USB hub. Be especially careful...

English102
4 Select “OK” and press the SET button.
hThe camera changes to the PC connection mode.
hTo continue the procedure, please read the Instruction Manual for the 
SANYO Software Pack.
NOTE
iWhen the digital camera is set to the PC connection mode, no image is 
shown on the LCD monitor.
Data file formats
The format of the files saved on the card and the method in which the file 
names are determined are explained below.
* Consecutive numbers assigned in the order the data was saved.Type of dataData...

103English
CONNECTING TO A COMPUTER
Configuration of directories for the stored data
NOTE 
Do not modify the folders and file names in the card using your 
computer 
iIf the folders, file names, or their configuration is modified using a personal 
computer, it will be impossible to play back the data using the digital 
camera, and the digital camera may not operate properly. 
Concerning video clip data saved by the digital camera 
iYou can use QuickTime 3 or later from Apple to play back the video clips....

English104
DIRECT-PRINT
Your digital camera supports the PictBridge function. By connecting the digital 
camera directly to a PictBridge-enabled printer, the digital camera’s LCD 
monitor can be used to select images and initiate printing.
Print preparations
1 Install the card containing the images you want to print in the digital 
camera. 
hIf there is no card installed in the camera, the image data from the 
cameras internal memory will be printed.
2 Use the supplied USB interface cable to connect the...

105English
DIRECT-PRINT
3 Turn on the power to the printer. 
4 Set the main switch to [ ].
hThe screen to confirm the 
connection appears.
5 Select “OK” and press the SET 
button.
hThe camera changes to the 
PictBridge printing mode, and the 
Print Settings Screen appears.
CAUTION
iDuring PictBridge printing, the camera’s button operation response is 
slower.
iIf the camera is powered by batteries for printing, make sure that the 
remaining battery charge is sufficient (see page 99).
PC
ONE IMAGE
Print...

English106
To select one image and print it (print select image)
Procedure to select one still image and print it.
1 Complete the print preparations (see page 104).
2 Select the choose print image icon 
, and press the SET button.
hThe screen to select images for 
printing appears.
3 Press the [l] or [m] arrow button to display the image you wish to 
print.
ONE IMAGE
COPIES 1
PRINT
EXIT
Downloaded From camera-usermanual.com Sanyo Manuals 

107English
DIRECT-PRINT
4 Specify the number of prints. 
1Select “COPIES”, and press the 
SET button. 
2Press the [n] or [o] arrow button to 
set the number of prints.
3Press the SET button. 
h“PRINT” is selected.
5 Press the SET button. 
hPrinting begins. 
NOTE 
To cancel printing 
1During printing, press the [o] arrow button.
hThe Confirm Cancel Printing Screen appears. 
2Select “YES”, and press the SET button. 
hIf “NO” is selected, printing resumes. 
ONE IMAGE
COPIES 1
PRINT
EXIT
Downloaded From...