Samsung Ud55ep Manual

41
Connecting an External Monitor
 •Do not connect the power cable before connecting all other cables.
Ensure you connect a source device first before connecting the power cable.
 ―
Connecting parts may differ in different products.
 ―The DP OUT (LOOPOUT) port is only available when the input source is PC, DVI , HDMI1, HDMI2 (PC connection), DisplayPort, MagicInfo or MagicInfo S.
 ―
When you play content using Player (MagicInfo S) on the home screen, Loopout is supported only for images. It is not...

42
Connecting to a Video Device
 •Do not connect the power cable before connecting all other cables.
Ensure you connect a source device first before connecting the power cable.
 •You can connect a video device to the product using a cable.
 ―
Connecting parts may differ in different products.
 ―Press the SOURCE button on the remote control to change the source.
Connection Using the AV Cable
AV / COMPONENT
 
AUDIO IN
Connection Using the component Cable
AV / COMPONENT
 
AUDIO IN      

43
Connection Using an HDMI-DVI Cable
 ―Audio will not be enabled if the product is connected to a video device using an HDMI-DVI cable. To resolve this, additionally connect an audio cable to the audio ports on the product and video device.
 ―After connecting a video device to the product with an HDMI-DVI cable, make sure to configure the settings as shown below to enable the video and audio from the video device.
You can use the DVI port on the product as an HDMI port by using a DVI-HDMI adapter.
 ―...

44
Connection Using an HDMI Cable
Using an HDMI cable or HDMI to DVI Cable (up to 1080p)
 •For better picture and audio quality, connect to a digital device using an HDMI cable.
 •
An HDMI cable supports digital video and audio signals, and does not require an audio cable.
 -To connect the product to a digital device that does not support HDMI output, use an HDMI-
DVI and audio cables.
 •
The picture may not display normally (if at all) or the audio may not work if an external device that 
uses an older...

45
Connecting the LAN Cable
 ―Connecting parts may differ in different products.
RJ45
 • Use Cat7(*STP Type) cable for the connection. 
*Shielded Twist Pair.   

46
Changing the Input source
Source
SOURCE → Source  
Source
MagicInfo S
HDMI1 HDMI2 Component
AV
PC
To go to Options, press and hold the Enter button.
 -
The displayed image may differ depending on the model.
Source  allows you to select a variety of sources and change source device names.
You can display the screen of a source device connected to the product. Select a source from source list to display the screen 
of the selected source.
 ― The input source can also be changed by using the SOURCE...

47
Using MDC
MDC Program Installation/Uninstallation
Installation
 ―MDC installation can be affected by the graphics card, mother board and network conditions.
1 Click the MDC Unified installation program.
2 Select a language for installation. Next, click "OK".
3 When the " Welcome to the InstallShield Wizard for MDC_Unified " screen appears, click "Next".
4 In the "License Agreement" window displayed, select  
"I accept the terms in the license agreement" and...

48
Connecting to MDC
Using MDC via RS-232C (serial data communications standards)
An RS-232C serial cable must be connected to the serial ports on the PC and monitor.
RS232C IN RS232C OUT
Monitor 1
Monitor 2
Computer    

49
Using MDC via Ethernet
Enter the IP for the primary display device and connect the device to the PC. Display devices can be connected to each other using a LAN cable.
Connection using a direct LAN cable
 ―Multiple products can be connected using the RJ45 port on the product and the LAN ports on the HUB.
RJ45
HUB
Monitor 1
Monitor 2 Computer  

50
Connection using a cross LAN cable
 ―Multiple products can be connected using the RS232C IN / OUT port on the product.
Monitor 1
Monitor 2
Computer
RS232C OUT
RJ45