Samsung Syncmaster T200g User Manual

You can choose one of nine languages.
 Note
The  language 
chosen affects only the language of the OSD. It has no effect on any software running
on the computer.
MENU →   ,   →   →   →   ,   → MENU
H-Position You can change the horizontal position where the OSD menu appears on your monitor.
MENU → 
 ,   →   →   ,   →   →   ,   → MENU
V-Position You can change the vertical position where the OSD menu appears on your monitor.
MENU → 
 ,   →   →   ,   →   →   ,   → MENU
Transparency Adjusting the Monitor
50
 

Change the transparency of the background of the OSD.
• Off •On
MENU →   ,   →   →   ,   →   →   ,   → MENU
Display Time The menu will be automatically turned off if no adjustments are made for a certain time period.
You can set the amount of time the menu will wait before it is turned off.
• 5 sec •10 sec •20 sec •200 sec
MENU →   ,   →   →   ,   →   →   ,   → MENU
 Setup
Reset Reverts the product settings to factory defaults.
• No •Yes
MENU →   ,   →   →   ,   →   →   →   ,   → Adjusting the Monitor
51 

Customized Key
You can specify a function which will be activated when the 
Customized Key ( )is pressed.
MENU →   ,   →   →   ,   →  →   ,   →MENU
Auto Source Select 
Auto Source for the monitor to automatically select the signal source.
• Auto •Manual
MENU →   ,   →   →   →   ,   → MENU
Image Size You can change the size of the screen displayed on your monitor.
•
Auto - The screen is displayed in accordance with the screen aspect ratio of the input signals.
• Wide - A full screen is displayed...

 Note
• Signals not available in the standard mode table are not supported.
•
If the wide screen which is the optimal resolution for the monitor is set on your PC, this function
is not performed.
MENU →   ,   →   →   ,   →  →  ,   → MENU
LED Brightness Adjusts the brightness of the Power LED.
• Off •On
MENU →   ,   →   →   ,   →  →  ,   → MENU
RTA RTA (Response Time Accelerator)
A 
function 

that accelerates the response speed of the panel so as to provide a sharper and more natural
video display.
• Off...

 Information
Shows a video source, display mode on the OSD screen.
MENU → 
 ,   →MENU
Adjusting the Monitor
54 

Troubleshooting
{T190,T190G}
Self-Test Feature Check
 Note
Your  monitor 
provides a self test feature that allows you to check whether your monitor is functioning
properly.
Self-Test Feature Check 1. Turn off both your computer and the monitor.
2. Unplug the video cable from the back of the computer.
3. Turn on the monitor.If the monitor is functioning properly, you will see a box in the illustration below. This box appears during normal operation if the video cable becomes disconnected or damaged.
4....

Useful Tips
A monitor 
recreates visual signals received from the computer. Therefore, if there is a problem with
the computer or the video card, this can cause the monitor to become blank, have poor coloring, become
noisy, and video mode not supported, etc. In this case, first check the source of the problem, and then
contact the Service Center or your dealer.
Judging the monitor's working condition
If there is no image on the screen or a " Not Optimum Mode", "Recommended Mode 1440 x 900...

A: You 
can see this message when the signal from the video card exceeds the maximum resolution
and frequency that the monitor can handle properly.
A:
Adjust the maximum resolution and frequency that the monitor can handle properly.
A: If the display exceeds SXGA or 75 Hz, a " Not Optimum Mode", "Recommended Mode  1440
x 900 60 Hz" message is displayed. If the display exceeds 85 Hz, the display will work properly
but the " Not Optimum Mode ", "Recommended Mode  1440 x 900 60...

A: Adjust the resolution and frequency at the video card.
(Refer to the Preset Timing Modes ).
Q:
The screen can be unbalanced due to the cycle of the video card signals. Readjust Position by
referring to the OSD.
The screen is out of focus or OSD cannot be adjusted.
Q: Have you adjusted the resolution or frequency on the monitor?
A: Adjust the resolution and frequency of the video card. (Refer to the Preset Timing Modes).
LED is blinking but no images on the screen.
Q: Is the frequency properly adjusted...

Control Panel  → 
Performance  and Maintenance  → System  → Hardware  → Device Manager
→ Monitors → After deleting Plug and Play monitor, find 'Plug and Play monitor' by searching
new Hardware.
A: MagicTune™  is  an  additional  software  for  the  monitor.  Some  graphic  cards  may  not  support your monitor. When you have a problem with the graphic card, visit our website to check the
compatible graphic card list provided.
http://www.samsung.com/monitor/magictune
MagicTune™ doesn't work...