Samsung Syncmaster P2770hd User Manual

							Using the Product3-6
3-6 Standard Signal Mode Table
 An LCD monitor has one optimal resolution for the best visual quality depending on the screen size due to the inherent 
characteristics of the panel, unlike a CDT monitor.
Therefore, the visual quality will be degraded if the optimal resolution is not set for the panel size. It is recommended setting 
the resolution to the optimal resolution of the product.
 
If the signal from the PC is one of the following standard signal modes, the screen is set automatically. However, if the signal from 
the PC is not one of the following signal modes, a blank screen may be displayed or only the Power LED may be turned on. 
Therefore, configure it as follows referring to the User Manual of the graphics card.
 
						

							3-6Using the Product
Horizontal Frequency
The time taken to scan one line from the left-most position to the right-most position on the screen is called the horizontal cycle 
and the reciprocal of the horizontal cycle is called the horizontal frequency. The horizontal frequency is represented in kHz.
Vertical Frequency
A panel must display the same picture on the screen tens of times every second so that humans can see the picture. This 
frequency is called the vertical frequency. The vertical frequency is represented in Hz.
RESOLUTION
HORIZONTAL 
FREQUENCY 
(KHZ)VERTICAL 
FREQUENCY  
(HZ)CLOCK 
FREQUENCY 
(MHZ)
POLARITY (H/V)
IBM, 640 x 350 31.469 70.086 25.175 +/-
IBM, 640 x 480 31.469 59.940 25.175 -/-
IBM, 720 x 400 31.469 70.087 28.322 -/+
MAC, 640 x 480 35.000 66.667 30.240 -/-
MAC, 832 x 624 49.726 74.551 57.284 -/-
MAC, 1152 x 870 68.681 75.062 100.000 -/-
VESA, 640 x 480 37.861 72.809 31.500 -/-
VESA, 640 x 480 37.500 75.000 31.500 -/-
VESA, 800 x 600 35.156 56.250 36.000 +/+
VESA, 800 x 600 37.879 60.317 40.000 +/+
VESA, 800 x 600 48.077 72.188 50.000 +/+
VESA, 800 x 600 46.875 75.000 49.500 +/+
VESA, 1024 x 768 48.363 60.004 65.000 -/-
VESA, 1024 x 768 56.476 70.069 75.000 -/-
VESA, 1024 x 768 60.023 75.029 78.750 +/+
VESA, 1152 x 864 67.500 75.000 108.000 +/+
VESA, 1280 X 800 49.702 59.810 83.500 -/+
VESA, 1280 X 960 60.00060.000 108.000 +/+
VESA, 1280 X 1024 63.981 60.020 108.000 +/+
VESA, 1280 X 1024 79.976 75.025 135.000 +/+
VESA, 1440 x 900 55.935 59.887 106.500 -/+
VESA, 1600 x 1200 75.000 60.000 162.000 +/+
VESA, 1680 x 1050 65.290 59.954 146.250 -/+
VESA, 1920 x 1080 (RB) 
(P2770HD)66.587 59.934 138.500 +/-
VESA,1920 x 1080
(P2370HD, P2570HD)67.500 60.000 148.500 +/+
 
						

							Installing the Software4-1
4 Installing the Software
4-1 Natural Color
What is Natural Color ?
This software is for Samsung products only and enables you to adjust the displayed colors on the product so they more closely 
match the colors of printed pictures. For more information, refer to the online help of the software (F1).
 Natural Color is provided online. You can download it from the website below and install;
http://www.samsung.com/us/consumer/learningresources/monitor/naturalcolorexpert/pop_download.html
 
 
						

							4-2Installing the Software
4-2 MultiScreen
What is MultiScreen ?
MultiScreen enables you to partition multiple sections on the Monitor.
Installing the Software
1.Insert the installation CD into the CD-ROM drive. 
2.Select the MultiScreen setup program.
 If the pop-up screen for the software installation does not appear on the main screen, find and double-click the 
MultiScreen setup file on the CD-ROM.
 
3.When the Installation Wizard appears, click [Next].
4.Complete the remaining software installation steps according to the instructions displayed on the screen.
 • The software may not work properly if you do not restart the computer after the installation.
• The MultiScreen icon may not appear depending on the computer system and the product specifications.
• If the shortcut icon does not appear, press the F5 key.
 
MultiScreen Installation Requirements
The MultiScreen installation may be affected by the graphics card, motherboard and the networking environment. 
Operating System
OS
• Windows 2000
• Windows XP Home Edition
• Windows XP Professional
• Windows Vista
 For MultiScreen, Windows 2000 or later operating systems are recommended.  
Hardware
• At least 32MB of memory 
• At least 60MB of free space on the hard disk drive 
Removing the Software 
Click [Start], select [Settings]/[Control Panel], and then double-click [Add or Remove Programs]. 
Select MultiScreen from the program list and click the [Add/Delete] button. 
 
						

							Troubleshooting5-1
5 Troubleshooting
5-1 Monitor Self-Diagnosis
 • You can check if the product is working properly using the Self-Diagnosis function.
• If a blank screen is displayed and the Power LED blinks even if the product and the PC are properly connected, perform 
the self-diagnosis function according to the procedures below.
 
1.Turn the product and the PC off.
2.Remove the D-Sub cable from the product. 
3.Turn the product on. 
4.If the product is working properly, the  message appears.
In this case, if a blank screen is displayed again, make sure that there is no problem with the PC and the connection.
 
						

							5-2Troubleshooting
5-2 Before Requesting Service
 Please check the following before requesting After-Sales service. If the problem continues, please contact your nearest 
Samsung Electronics Service Center.
 
PROBLEMS RELATED TO INSTALLATION (PC MODE)
The monitor screen flickers. Check if the signal cable between the computer and the monitor is securely 
connected and tightened.
(Refer to Connecting to a Computer) 
PROBLEMS RELATED TO SCREEN
Screen is blank and power indicator is off. Ensure that the power cord is firmly connected and the LCD monitor is on.
(Refer to Connecting to a Computer) 
  message Ensure that the signal cable is firmly connected to the PC or video sources.
(Refer to Connecting to a Computer) 
 message Check the maximum resolution and the frequency of the video adapter.
Compare these values with the data in the Preset Timing Modes Chart. 
Picture rolls vertically. Check if the signal cable is securely connected.Connect it again securely. 
(Refer to Connecting to a Computer) 
Image is not clear. Picture is blurred. Run Frequency  and < Fine> tuning.
Turn on again after removing all accessories(video extension cable, etc.)
Set resolution and frequency to the recommended ranges.
Picture image is unstable and vibrates. Check if the resolution and frequency set for the computer video card falls 
in the range supported by the monitor. If not, reset them referring to the 
current  under the monitor menu and Standard Signal Mode 
Table.
Ghost images are shown in the picture.
The image is too light or too dark Adjust the  and 
(Refer to the , ) 
Screen is blank and the power indicator light 
blinks every 0.5 or 1 secondsThe monitor is using its power management system
Press a key on the keyboard
The screen is blank and is blinking. If you see the message on the screen when you press the 
[ MENU] button, check the cable connection between the monitor and the 
computer to ensure that the connector is properly connected.
PROBLEMS RELATED TO AUDIO
No sound Ensure that the audio cable is firmly connected to both the audio-in port on 
your monitor and the audio-out port on your sound card.
(Refer to Connecting to a Computer) 
Check the volume level.
The sound level is too low. Check the volume level.
If the volume is still too low after turning the control to its maximum, check 
the volume control on the computer sound card or software program.
PROBLEMS RELATED TO REMOTE CONTROL 
The remote control buttons do not respond. Check the battery polarities (+/-).
Check if the batteries have been exhausted.
Check if the power is on.
Check if the power cord is securely connected.
Check if a special fluorescent or neon lamp is on in the vicinity
 
						

							Troubleshooting5-2
NOTE ON THE PRODUCT APPEARANCE
You may see small particles if you look closely at 
the edge of the bezel surrounding the screen.This is part of the products design and is not a defect.
 
						

							5-3Troubleshooting
5-3 FAQ
FAQPLEASE TRY THE FOLLOWING!
How can I change the frequency of the video sig-
nal?You have to change the frequency of the graphics card.
(For more information, refer to the User Manual of the computer or the 
graphics card.) 
How can I change the resolution? Windows XP: Change the resolution by selecting Control Panel →Appear-
ance and Themes→Display→Settings.
Windows ME/2000 : Change the resolution by selecting Control Panel 
→Appearance and Themes→Display→Settings.
(For more information, refer to the User Manual of the computer or the 
graphics card.)
How can I use the power saving function? Windows XP: Configure it by selecting Control Panel→Appearance and 
Themes→Display→Screen Saver Setting or configure it in the BIOS 
SETUP of the computer.
Windows ME/2000 : Configure it by selecting Control Panel→Appearance 
and Themes→Display→Screen Saver Setting or configure it in the BIOS 
SETUP of the computer.
For more information, refer to the Windows user manual for the computer.
How can I clean the outer case/LCD Panel? Disconnect the power cord and then clean the monitor with a soft, dry or 
slightly damp cloth.
Do not leave any detergent or scratches on the case.
Do not let any water enter the monitor.
What is the difference between HDTV and 
SDTV?There are various types of digital TVs.
The most widely known types of digital TV are HDTV and SDTV. They are 
classified according to the screen quality and the video specifications.
• HDTV (High Definition TV):High screen quality.
• SDTV (Standard Definition TV):Common standard digital TV.
An SDTV has an aspect ratio of 4:3 which is the same as that of an analog 
TV. HDTV has an aspect ratio of 16:9 which is similar to a cinema screen. 
This provides a much better screen quality than SDTV.
Digital TV broadcasting in our country is ultimately orientated towards 
HDTV. (At present, all digital TVs from Samsung Electronics have the 16:9 
wide aspect ratio.)
Can I watch HD broadcasting with all digital 
TVs?You can receive all digital broadcasts, whether they are SD or HD, using
any digital TV. However, you cannot enjoy HD programs, which are the
highest quality digital TV programs, using an SD digital TV.
(At present, all digital TVs from Samsung Electronics have the 16:9 wide
aspect ratio.)
Can I watch digital TV broadcasting with an ana-
log TV?No.
The analog TV cannot interpret digital signals. Therefore, a digital TV is 
required to watch digital TV broadcasting.
Can I use my present antenna to receive digital 
broadcasting?As for existing analog TV, digital TV is designed so that digital broadcast-
ing signals are received via both indoor and outdoor antennas.
If signal reception is very good in your environment, you can watch digital 
broadcasts with your existing indoor antenna. If not, it is better to install an 
outdoor antenna.
 
						

							More Information6-1
6 More Information
6-1 Specifications
MODEL NAMEP2370HDP2570HDP2770HD
LCD PanelScreen Size 23 inches (58 cm) 24.6 inches (62 cm) 27 inches (68 cm)
Display Area
509.76 mm
(H) X 286.74 
mm
(V) ( 20.06 inches X 
11.29 inches)543.46 mm
(H) X 305.69 
mm
(V) ( 21.40 inches X 
12.04 inches)597.89 mm (H) X 336.31 
mm (V) ( 23.5 inches X 13.2 
inches)
Pixel Pitch
0.2655 mm
(H) X 0.2655 
mm
(V) (0.01 inches X 0.01 
inches)0.283 mm
(H) X 0.283 mm

(V) (0.01 inches X 0.01 
inches)0.3114 mm
(H) X 0.3114 
mm (V) (0.01 inches X 0.01 
inches)
Synchroniza-
tionHorizontal 30~81 kHz
Vertical 56~75 Hz
Color 16.7M
ResolutionOptimal Reso-
lution1920x1080 @ 60 Hz 1920x1080 @ 60 Hz (RB)
Maximum Res-
olution1920x1080 @ 60 Hz 1920x1080 @ 60 Hz (RB)
Input Signal, TerminatedRGB analog, DVI (Digital 
Visual Interface) compati-
ble digital RGB
0.7 Vp-p ± 5 %
Separate Type H/V Sync, 
Composite
TTL Level (V high ≥ 2.0 V, V 
low ≤ 0.8 V)RGB analog, DVI (Digital 
Visual Interface)
0.7 Vp-p ± 5 %
Separate Type H/V Sync, 
Composite
TTL Level (V high ≥ 2.0 V, V 
low ≤ 0.8 V) RGB analog, DVI (Digital 
Visual Interface) 
0.7 Vp-p ± 5 % 
Separate Type H/V Sync, 
Composite 
TTL Level (V high ≥ 2.0 V, V 
low ≤ 0.8 V) 
Maximum Pixel Clock 162.000MHz (Analog,Digital)
Power Voltage AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Dimension (Width x Height x 
Depth) / Weight571 x 364.6 x 65.5 mm 
(22.5 x 14.4 x 2.6 inches) 
(Without Stand)
571 x 432.5 x 189.5 mm 
(22.5 x 17 x 7.5 inches) 
(With Stand) / 5.8 kg (12.8 
Ibs)605 x 384 x 66 mm (23.8 x 
15.1 x 2.6 inches) (Without 
Stand) / 6.3 kg (13.9 Ibs)
605 x 453 x 240 mm (23.8 x 
17.8 x 9.4 inches) (With 
Stand) / 7 kg (15.4 Ibs)667 x 422 x 66 mm ( 26.3 x 
16.6 x 2.6 inches) (Without 
Stand) / 7.4 kg ( 16.3 Ibs)
667 x 484 x 244 mm (26.3 x 
19.1 x 9.6 inches) (With 
Stand) / 8.2 kg ( 18.1 Ibs)
VESA Mounting Interface 75 mm x 75 mm
(2.95 x 2.95 inches) 100 mm x 100 mm
(3.94 x 3.94 inches)100 mm x 100 mm
(3.94 x 3.94 inches)
Environmental 
considerationsOperating Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Humidity : 10 % ~ 80 %, non-condensing
Storage Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Humidity : 5 % ~ 95 %, non-condensing
Tilt -2° ~ 22°
 
						

							6-1More Information
 Class B (Information Communication Equipment for Home Use) 
This device has been registered regarding EMI for home use (Class B). It may be used in all areas. (Class B equipment 
emits less electromagnetic waves than Class A equipment.)